Bil, CHANGAN, RAETON, D18T UAES engine system (UDS)
Motor - D18T UAES engine system (UDS) - 0
Identifikation
Systemidentifikation: D1234
Stel nr.:
Hardware number: SABCDEFGHI
Software nummer: T1234567
Fejlkoder
P2122: Accelerator pedal position sensor 1/A/single - circuit low voltage
P0651: Ukendt fejlkode
P0100: Ukendt fejlkode
P1204: Ukendt fejlkode
Controls
Clear DTC
Levende Data
Batteri spænding: -- V
Faktisk motordrejningsmoment: 21.18 %
Ignition angle actual: -96.00 Grad kw
Absolute intake manifold pressure: 0.0000 hPa
Target intake manifold pressure: 0.0000 V
Actual torque at response of torque comparison in the function monitoring: 33.20 %
Additive correction of the mixture adaptation: -1536.00
Ambient pressure: 0.00 hPa
Ambient temperature: -48.00 °C
Intake valve opening (Relative to LWOT): -256.00 kW
Tændings vinkel: -96.00 Grad kw
Battery voltage (ADC): 22.59 km/h
Calculated actual torque in function monitoring: 0.00 %
Catalytic converter downstream temperature: 375 °C
O2 sensor bank 1 upstream catalyst system modelled exhaust gas temperature: -273.15 °C
Desired engine torque - Crankshaft torque: 7.06 %
Target idle speed: 0 Omdr.
Voltage DK-Poti 1 at the NLP-position: 5.65 kW
PWG potentiometer 2: 21.33 V
Motorkølevæsketemperatur: 15.75 °C
Motor Hastighed: 0.00 Omdr.
Motor kølevæske temperatur føler: 15.75 °C
Coolant temperature at engine start: -48.00 °C
ETS-path as environmental condition for diagnosis of function monitoring: 0
Fluid temperature sensor: -273.15 °C
Brændstofniveau: 0.00 L
Fuel volume flow: 0.0000 L/s
Calculated total HFM mass air flow: 0.00 kg/h
Ignition-timing retardation for dynamics cylinder 1: -96.00 Grad kw
Ignition-timing retardation for dynamics cylinder 2: -96.00 Grad kw
Ignition-timing retardation for dynamics cylinder 3: -96.00 Grad kw
Ignition-timing retardation for dynamics cylinder 4: -96.00 Grad kw
Indsprøjtnings tid B1: 0.00 ms
Indsugningslufttemperatur: -48.00 °C
Absolute intake manifold pressure: 0.00 hPa
Intake manifold switchover: Sluk
Reference level knock control, cylinder 1: 0.0000 V
Reference level knock control, cylinder 2: 0.0195 V
Reference level knock control, cylinder 3: 0.0000 V
Reference level knock control, cylinder 4: 0.0041 V
Target mass air flow: 476 kg/h
OBD maximum indicated torque: 0.00 %
Distance since check engine telltale on: 0 km
Engine speed maximum area of misfire: 0 Omdr.
Engine speed minimum area of misfire: 3400 Omdr.
O2 sensor controller: 0.0000
Lambda controller output (bank 2): 0.0000
O2 sensor 1, bank 1 status: 0.0000 V
O2 sensor 2, bank 1 status: 0.0000 V
Standardized mass flow from canister purge control: 1.8070 kg/h
A/C clutch: Tænd
køler blæser relæ: Tænd
Køleventilatorrelæ 2: Tænd
Fuel pump relay: Tænd
Target torque change from the idle speed control (PD-part): -100.0000 %
Number of clutch operations detected: 0
Current misfire, cylinder 1: 0
Current misfire, cylinder 2: 65535
Current misfire, cylinder 3: 65535
Current misfire, cylinder 4: 65535
Throttle blade position dependent on potentiometer 1: -687.06 %
Throttle blade position dependent on potentiometer 2: -687.06 %
Target throttle valve position: Tænd
Sensor voltage from throttle potentiometer 1: 5.65 V
Sensor voltage from throttle potentiometer 2: 0.00 V
Torque path in function and function monitoring as environmental condition of diagnostic: 0
Target idle speed: 0 Omdr.
Longitudinal acceleration vehicle reference: -27.78 m/s²
Køretøjs hastighed : 0.00 km/h
PWG potentiometer 1: 22.59 V
PWG potentiometer 2: 0.00 V
Udgangs test
Controls
Evaporative emission (EVAP) system, canister purge valve
Brændstofpumperelæ
køler blæser relæ
Køleventilatorrelæ 2
A/C clutch
Gasspjæld position vinkel
Idle rpm control
Muligheder
Controls
Rediger stel nr.
Resetting of all adaptation values
Reset long term fuel self-learning adjustment