Car, HOLDEN, Spark, 2016, 1.4L (LV7) - 1.4L (LV7)

Data version: --

VIN no: W0LGT8EBXA1007787

Subscriber ID: O100057235

Programming date: 8209

Identifier: 00 00

System code: 00

XML configuration compatibility identifier: 1

XML data file part number: 0

XML data file alpha code:

Previous subscriber ID: *10MDZ7

2nd previous subscriber ID: *10MDZ7

Manufacturer enable counter (MEC): 0

ECU diagnostic address: --

Detected system: --

Detected component: --

Detected RPO: --

Manufacturer`s traceability number: --

Broadcast code: --

Boot software part number: 0

Software module 1 identifier: 12654173

Software module 2 identifier: 55577673

Software module 3 identifier: 55577209

Software module 4 identifier: 55577673

Software module 5 identifier: 847

Software module 6 identifier: 55573530

Software module 7 identifier: 55573530

Software module 8 identifier: 55573530

Software module 9 identifier: --

Software module 10 identifier: --

End model part number: 55577619

Base model part number: 55574337

Software part number alpha code: --

Software module 1 identifier alpha code: AA

Software module 2 identifier alpha code: AA

Software module 3 identifier alpha code: AA

Software module 4 identifier alpha code: --

Software module 5 identifier alpha code: --

Software module 6 identifier alpha code: --

Software module 7 identifier alpha code: --

Software module 8 identifier alpha code: --

Software module 9 identifier alpha code: --

Software module 10 identifier alpha code: --

End model part number alpha code: 00

Base model part number alpha code: 00

Clear DTC

Indicated fuel consumption: -- L

Real fuel consumption: -- L

Check engine telltale request: No

Engine load: 0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim: -100 %

Long term fuel trim: -100 %

MAP sensor: 0 kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Intake air temperature sensor 1: -40 °C

Mass air flow sensor: 0.00 g/sec

Alternative fuel rail pressure sensor: 0 kPa

EVAP purge solenoid valve command: 0 %

Remaining fuel in tank: 0 %

Warm-ups since DTC cleared: 0 Counts

Distance since DTC cleared: 0 km

Baro: 0 kPa

Calculated catalyst temperature: -40 °C

Ignition 1 signal: 0.00 V

Air/Fuel equivalence ratio command: 0.00

Air/Fuel equivalence ratio command: 0.00 lambda

Ambient air temperature: -40 °C

Idle speed adjustment: -- rpm

Idle speed correction: -- rpm

Target throttle position: 0 %

Current fuel type: Not available

Engine oil temperature: -40 °C

Driver requirement torque: -125 %

Electronic throttle control (ETC) system forced engine shutdown: No

Reduced engine power: Inactive

Wide open throttle: No

APP sensor 1 and 2: Agree

Electronic throttle control (ETC) motor: Enabled

Throttle position sensors 1 and 2: Agree

Cooling fan relay 2 command: Off

Cooling fan relay 1 command: Off

A/C request: No

A/C cut-off due to A/C pressure out of range: No

A/C Off for WOT: No

A/C compressor clutch relay command: Off

Brake pedal position sensor fully released learn status: Incomplete

Extended travel brake pedal position signal: Released

Brake pedal position circuit signal: Released

Brake pedal position sensor signal: Released

Clutch pedal starter inhibit switch: On

Clutch pedal: No

Reverse position switch: Off

O2 sensor 2, bank 1 heater: Off

O2 sensor 1, bank 1 heater: Off

Change engine oil indicator command: Off

Low engine oil level indicator command: Off

Low engine oil pressure indicator command: Off

Cold start: No

P/N switch: Inactive

Engine controls ignition relay command: Off

Ignition accessory signal: Off

Fuel enrichment - hot catalyst: Inactive

Fuel enrichment - hot coolant: Inactive

Power enrichment: Inactive

Fuel control loop status: Open

Deceleration fuel cut-off: Inactive

Fuel trim learn: Disabled

Throttle position performance test: Ok

MAP performance test 2: Ok

MAP performance test 1: Ok

MAF performance test: Ok

A/C high side pressure sensor: 0.00 V

Engine oil temperature calculated: -40 °C

Fuel level sensor: 0.00 V

Traction control torque request signal: 0 %

Engine oil pressure sensor: 0.00 V

Crankshaft position active counter: 0 Counts

Crankshaft position resync counter: 0 Counts

Coolant temperature at engine start: -40 °C

Traction control torque delivered signal: 0 %

Fuel trim memory cell: 0

Torque management ignition timing retard: 0 °

Knock retard: 0 °

Calculated air flow: 0.00 g/sec

Target idle speed: 0 rpm

Total number of misfire: 0 Counts

Misfire historic, cylinder 1: 0 Counts

Misfire historic, cylinder 2: 0 Counts

Misfire historic, cylinder 3: 0 Counts

Misfire historic, cylinder 4: 0 Counts

Current misfire, cylinder 2: 0 Counts

Current misfire, cylinder 1: 0 Counts

Current misfire, cylinder 3: 0 Counts

Current misfire, cylinder 4: 0 Counts

Cycles of misfire data: 0 Counts

Accelerator pedal position sensors: 0 %

Throttle position: 0 %

Accelerator pedal position sensor 1: 0 %

Accelerator pedal position sensor 2: 0 %

Throttle position sensor 1: 0 %

Throttle position sensor 2: 0 %

Throttle position sensor 2: 0.00 V

Throttle position sensor 1: 0.00 V

Accelerator pedal position sensor 2: 0.00 V

Accelerator pedal position sensor 1: 0.00 V

Injection time bank 1: 0.00 ms

Total knock retard: 0 °

Mass air flow sensor: 0 Hz

Total mass air flow: 0.00 g/sec

Misfire diagnostic engine speed: 0 rpm

Misfire diagnostic engine load: 0 %

Fuel tank rated capacity: 0 L

Accelerator pedal position: 0 %

Remaining fuel in tank: 0 L

Catalyst monitor test counter: 0 Counts

MIL control circuit high voltage test status: Malfunction

MIL control circuit low voltage test status: Malfunction

MIL control circuit open test status: Malfunction

Fuel pump relay control circuit high voltage test status: Malfunction

Fuel pump relay control circuit low voltage test status: Malfunction

Fuel pump relay command: Off

Fuel pump relay control circuit open test status: Malfunction

A/C compressor clutch relay control circuit high voltage test status: Failed

A/C compressor clutch relay control circuit low voltage test status: Failed

A/C compressor clutch relay control circuit open test status: Failed

Cooling fan motor command: 0 %

Throttle position sensor 1 fully close learn: 0.00 V

Throttle position sensor 2 fully close learn: 0.00 V

Engine off time: 00:00:00

Throttle motor PWM control signal: 0 %

Intake camshaft position actuator solenoid valve control circuit high voltage test status: Malfunction

Intake camshaft position actuator solenoid valve control circuit low voltage test status: Malfunction

Intake camshaft position actuator solenoid valve control circuit open test status: Malfunction

Exhaust camshaft position actuator solenoid valve control circuit high voltage test status: Malfunction

Exhaust camshaft position actuator solenoid valve control circuit low voltage test status: Malfunction

Exhaust camshaft position actuator solenoid valve control circuit open test status: Malfunction

Ignition coil 1 control circuit high voltage test status: Malfunction

Ignition coil 1 control circuit low voltage test status: Malfunction

Ignition coil 1 control circuit open test status: Malfunction

Ignition coil 2 control circuit high voltage test status: Malfunction

Ignition coil 2 control circuit low voltage test status: Malfunction

Ignition coil 2 control circuit open test status: Malfunction

Ignition coil 3 control circuit high voltage test status: Malfunction

Ignition coil 3 control circuit low voltage test status: Malfunction

Ignition coil 3 control circuit open test status: Malfunction

Ignition coil 4 control circuit high voltage test status: Malfunction

Ignition coil 4 control circuit low voltage test status: Malfunction

Ignition coil 4 control circuit open test status: Malfunction

Cylinder 1 injector control circuit high voltage test status: Malfunction

Cylinder 1 injector control circuit low voltage test status: Malfunction

Cylinder 1 injector control circuit open test status: Malfunction

Cylinder 2 injector control circuit high voltage test status: Malfunction

Cylinder 2 injector control circuit low voltage test status: Malfunction

Cylinder 2 injector control circuit open test status: Malfunction

Cylinder 3 injector control circuit high voltage test status: Malfunction

Cylinder 3 injector control circuit low voltage test status: Malfunction

Cylinder 3 injector control circuit open test status: Malfunction

Cylinder 4 injector control circuit high voltage test status: Malfunction

Cylinder 4 injector control circuit low voltage test status: Malfunction

Cylinder 4 injector control circuit open test status: Malfunction

EVAP purge solenoid valve control circuit high voltage test status: Malfunction

EVAP purge solenoid valve control circuit low voltage test status: Malfunction

EVAP purge solenoid valve control circuit open test status: Malfunction

Cooling fan control circuit high voltage test status: Malfunction

Cooling fan relay 1 control circuit high voltage test status: Failed

Cooling fan control circuit low voltage test status: Malfunction

Cooling fan relay 1 control circuit low voltage test status: Failed

Cooling fan control circuit open test status: Malfunction

Cooling fan relay 1 control circuit open test status: Failed

Cooling fan relay 2 control circuit high voltage test status: Failed

Cooling fan relay 2 control circuit low voltage test status: Failed

Cooling fan relay 2 control circuit open test status: Failed

Camshaft position sensor: 0 rpm

Crankshaft position sensor: 0 rpm

O2 sensor 1, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit open test status: Malfunction

O2 sensor 2, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit open test status: Malfunction

5V reference voltage circuit 1: 0.00 V

5V reference voltage circuit 2: 0.00 V

O2 sensor 1, bank 1 heater: 0 %

O2 sensor 1, bank 1 heater: 0.0 A

O2 sensor 2, bank 1 heater: 0.0 A

Engine controls ignition relay control circuit high voltage test status: Malfunction

Engine controls ignition relay control circuit low voltage test status: Malfunction

Engine controls ignition relay control circuit open test status: Malfunction

Engine controls ignition relay feedback signal: 0.0 V

A/C disengagement 1st history: None

A/C disengagement 2nd history: None

A/C disengagement 3rd history: None

A/C disengagement 4th history: None

A/C disengagement 5th history: None

A/C disengagement 6th history: None

A/C disengagement 7th history: None

A/C disengagement 8th history: None

A/C compressor clutch inhibit reason history 1: None

A/C compressor clutch inhibit reason history 2: None

A/C high side pressure sensor: 0 kPa

Fuel trim system test state: Disabled

Short term fuel trim test average: -100 %

Long term fuel trim test average: -100 %

Long term fuel trim test average without purge: -100 %

Knocking detected, cylinder 4: No

Knocking detected, cylinder 3: No

Knocking detected, cylinder 2: No

Knocking detected, cylinder 1: No

Injector disabled, cylinder 4 - misfire detected: No

Injector disabled, cylinder 3 - misfire detected: No

Injector disabled, cylinder 2 - misfire detected: No

Injector disabled, cylinder 1 - misfire detected: No

Exhaust camshaft position command: 0 %

Intake camshaft position command: 0 %

O2 sensor 2, bank 1 heater: 0 %

Exhaust camshaft position variance: 0 °

Intake camshaft position variance: 0 °

Exhaust camshaft position active counter: 0 Counts

Intake camshaft position active counter: 0 Counts

Output shaft speed sensor: 0 rpm

Engine oil pressure control test counter: 0 Counts

Calculated engine oil pressure: 0 kPa

Alternative fuel disable message: Enabled

Fuel mode request to ECM: Undetermined state

Fuel mode command from ECM: Undetermined state

Alternative fuel disable control circuit high voltage test status: Malfunction

Alternative fuel disable control circuit low voltage test status: Malfunction

Alternative fuel disable command: Enabled

Alternative fuel disable control circuit open test status: Malfunction

MAP sensor: 0.00 V

Intake air temperature sensor 1 at start: -40 °C

Intake air temperature sensor 2: -40 °C

Barometric pressure sensor: 0.00 V

Clutch pedal position sensor: 0.00 V

Clutch pedal position sensor learned apply position: 0.00 V

Clutch pedal position learn status: Performed successfully

Clutch pedal position sensor learned release position: 0.00 V

Clutch pedal position sensor: 0 %

Service vehicle soon (SVS) indicator command: Off

MIL requested by DTC: No

MIL command: Off

Drop-Throttle status: Inactive

Drag control status: Inactive

5V reference voltage circuit 4: Ok

5V reference voltage circuit 3: Ok

5V reference voltage circuit 2: Ok

5V reference voltage circuit 1: Ok

Fuel economy actual: 0.0 L/h

Redundant odometer memory: Not present

Replicated transmission OSS signal: 0 rpm

Torque request inhibit - minimum torque: No

Torque request inhibit - fuel: No

Torque request inhibit - ignition timing: No

Torque request inhibit - TAC: No

Torque request inhibit - minimum idle: No

5V reference voltage circuit 3: 0.00 V

5V reference voltage circuit 4: 0.00 V

Throttle body idle air flow compensation: 0 %

Speed limiting/warning: Inactive

Cruise control: Disabled

Generator indicator command: Off

Catalyst monitor test result: No decision

Catalyst monitor not at idle test conditions met: No

Catalyst monitor test state: Inactive

Reduced engine power history: None

Power mode: Off

Ignition 1 signal: Off

Accelerator pedal position sensor 2 - circuit status: Ok

Accelerator pedal position sensor 1 - circuit status: Ok

Brake pedal position sensor: 0.00 V

Brake pedal position sensor learned released position: 0.00 V

Brake pedal position sensor: 0 %

Engine calibration monitoring identifier: Not programmed

Engine calibration monitoring: Not present

Calculated barometric pressure: 0 kPa

Intake air temperature sensor 2: 0 Hz

Ambient humidity: 0 %

Intake air humidity sensor: 0 %

O2 sensor 1, bank 1: 0.00 V

O2 sensor 2, bank 1: 0.00 V

Crankshaft position signal output circuit high voltage test status: Malfunction

Crankshaft position signal output circuit low voltage test status: Malfunction

Crankshaft position signal output circuit open test status: Malfunction

Camshaft position signal output circuit high voltage test status: Malfunction

Camshaft position signal output circuit low voltage test status: Malfunction

Camshaft position signal output circuit open test status: Malfunction

Engine oil pressure: 0 kPa

Engine speed during misfire history 1: 0 rpm

Engine load during misfire history 1: -- %

Engine speed during misfire history 2: 0 rpm

Engine load during misfire history 2: -- %

Engine speed during misfire history 3: 0 rpm

Engine load during misfire history 3: -- %

Engine speed during misfire history 4: 0 rpm

Engine load during misfire history 4: -- %

Engine speed during misfire history 5: 0 rpm

Engine load during misfire history 5: -- %

Hood position: Closed

Driver requested axle torque: -22534 N·m

Traction control axle torque request signal: -22534 N·m

Traction control torque request signal: -848 N·m

Torque request inhibit - TAC limit: No

Torque request inhibit - ignition timing advance: No

Exhaust camshaft position: 0 °

Intake camshaft position: 0 °

Exhaust camshaft target position: 0 °

Intake camshaft position target: 0 °

Engine timing: No crank-/camshaft position sensor activity

Accelerator pedal position sensor 1 learned applied position: 0 %

Accelerator pedal position sensor 2 learned applied position: 0 %

Engine crank time: 0.00 sec

Intake air temperature sensor 2 at start: -40 °C

Current gear: Unknown

Accelerator pedal position sensor 1 learned released position: 0.00 V

Accelerator pedal position sensor 2 learned released position: 0.00 V

Engine oil pressure control solenoid valve control circuit high voltage test status: Malfunction

Engine oil pressure control solenoid valve control circuit low voltage test status: Malfunction

Engine oil pressure control solenoid valve command: High pressure

Engine oil pressure control solenoid valve control circuit open test status: Malfunction

Engine oil pressure control test disable history 1: None

Engine oil pressure control test disable history 2: None

Engine oil pressure control test inhibit history 1: None

Engine oil pressure control test inhibit history 2: None

O2 sensor 1, bank 1 heater: 0.00 V

Engine coolant temperature sensor: -40 °C

MAP sensor: 0 kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition 1 signal: 0.00 V

Reduced engine power: Inactive

A/C request: No

A/C compressor clutch relay command: Off

Clutch pedal starter inhibit switch: On

Clutch pedal: No

Reverse position switch: Off

Ignition accessory signal: Off

Remote vehicle start request signal: Off

Generator F terminal signal: 0 %

Target idle speed: 0 rpm

Accelerator pedal position: 0 %

Starter relay command: Off

Generator L - terminal command: 0 %

Engine controls ignition relay feedback signal: 0.0 V

Brake booster pressure sensor: 10.33 kPa

MIL requested by DTC: No

Reduced engine power history: None

Power mode: Off

Ignition 1 signal: Off

Stop/start system status: Active

Hood position: Closed

Engine stopping: No

System OFF: No

Engine running: No

Engine off: No

Engine starting: No

Engine stalled: No

Engine stopped: No

Autostop disable reason - transmission range: No

Autostop disable reason - hood ajar: No

Autostop disable reason - ECM request: No

Autostop disable reason - run/crank not active: No

Autostop disable reason - acceleration request: No

Autostop disable reason - minimum engine run time not met: No

Autostop disable reason - control function active: No

Autostop disable reason - ignition switch start: No

Autostop disable reason - engine coolant temperature out of range: No

Autostop disable reason - remote vehicle start request: No

Autostop disable reason - system optimization: No

Autostop disable reason - transmission in reverse: No

Autostop disable reason - system voltage low: No

Autostop disable reason - invalid data received: No

Autostop disable reason - tow/haul mode switch on: No

Autostop disable reason - vehicle speed too high: No

Autostop disable reason - reduced engine power active: No

Autostart inhibit reason - transmission range: No

Autostart inhibit reason - hood ajar: No

Autostart inhibit reason - ECM request: No

Autostart inhibit reason - run/crank not active: No

Autostart inhibit reason - system malfunction: No

Autostart inhibit reason - control function active: No

Autostart inhibit reason - autostart not commanded: No

Autostart inhibit reason - ECM malfunction: No

Autostart inhibit reason - crank aborted: No

Autostart inhibit reason - autostart/autostop malfunction: No

Autostart inhibit reason - compression test: No

Autostart inhibit reason - engine stop required: No

Autostart inhibit reason - driver exited vehicle: No

Autostart inhibit reason - engine coolant temperature out of range: No

Autostart inhibit reason - calibration override: No

Autostart reason - maximum autostop time exceeded: No

Autostart reason - reduced engine power active: No

Autostart reason - system malfunction: No

Autostart reason - remote vehicle start request: No

Autostart reason - system optimization: No

Autostart reason - transmission in reverse: No

Autostart reason - system voltage low: No

Autostart reason - invalid data received: No

Autostart reason - tow/haul mode switch on: No

Autostart reason - vehicle speed too high: No

Autostart reason - acceleration request: No

Autostart reason - minimum engine run time not met: No

Autostart reason - control function active: No

Autostart reason - ignition switch start: No

Autostart reason - engine coolant temperature out of range: No

Autostart reason - transmission range: No

Autostart reason - hood ajar: No

Autostart reason - ECM request: No

Autostop disable reason - 12V start counter exceeded: No

Autostop disable reason - brake pedal released: No

Autostop disable reason - vehicle inclination: No

Autostop disable reason - brake booster weak vacuum: No

Autostop disable reason - A/C request: No

Autostop disable reason - accelerator pedal pressed: No

Autostop disable reason - low-voltage battery voltage low: No

Autostop disable reason - low-voltage battery state of health low: No

Autostop disable reason - engine speed high: No

Autostop disable reason - low-voltage battery state of charge low: No

Autostop disable reason - wheel slip detected: No

Autostop disable reason - low-voltage battery discharge current high: No

Autostop disable reason - vehicle speed threshold not reached: No

Autostop disable reason - intake manifold weak vacuum: No

Autostop disable reason - maximum vehicle stop time exceeded: No

Autostop disable reason - starter system malfunction: No

Autostop disable reason - generator load high: No

Autostop disable reason - system malfunction: No

Autostop disable reason - clutch pedal applied: No

Autostop disable reason - stop/start select switch: No

Autostop disable reason - low-voltage battery temperature out of range: No

Autostop disable reason - idle boost mode active: No

Autostop disable reason - low-voltage battery state of function low: No

Autostop disable reason - turn signal active: No

Autostop disable reason - passenger compartment heater on: No

Autostop disable reason - deceleration rate too high: No

Autostop disable reason - driver exited vehicle: No

Autostart reason - low-voltage battery discharge current high: No

Autostart reason - brake pedal released: No

Autostart Reason - inclination: No

Autostart reason - brake booster weak vacuum: No

Autostart reason - A/C request: No

Autostart reason - accelerator pedal pressed: No

Autostart reason - low-voltage battery voltage low: No

Autostart reason - clutch pedal applied: No

Autostart Reason - passenger compartment heater on: No

Autostart reason - low-voltage battery state of function low: No

Autostart reason - driver exited vehicle: No

Autostart reason - low-voltage battery state of health low: No

Autostart reason - stop/start select switch: No

Autostart reason - low-voltage battery state of charge low: No

Battery voltage high resolution: 0.00 V

Low-voltage battery current: 0.00 A

Low-voltage battery temperature: -40 °C

Low-voltage battery state of function: 0.00 V

Low-voltage battery state of health: 0 %

Low-voltage battery state of charge: 0 %

Engine timing: No crank-/camshaft position sensor activity

Neutral position sensor: Neutral

Engine crank time: 0.00 sec

Autostop disable reason - MAF sensor test in progress: No

Autostop disable reason - MAP sensor test in progress: No

Autostop disable reason - barometric pressure too low: No

Stop/Start system disable reason - engine oil temperature out of range: No

Autostop disable reason - O2 sensor test in progress: --

Autostop disable reason - misfire test in progress: --

Autostop disable reason - engine speed test in progress: --

Autostop disable reason - catalyst not at operating temperature: --

Autostop disable reason - catalyst test in progress: --

Autostop disable reason - intake manifold temperature too high: --

Engine hood switch: Closed

Battery voltage: -- V

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Ignition 1 signal: 0.00 V

Target throttle position: 0 %

Driver requirement torque: -125 %

Extended travel brake pedal position signal: Released

Brake pedal position circuit signal: Released

Traction control torque request signal: 0 %

Traction control torque delivered signal: 0 %

Torque management ignition timing retard: 0 °

Target idle speed: 0 rpm

Throttle position: 0 %

Cruise control disengagement 1st history: Brake pedal applied

Cruise control disengagement 2nd history: Brake pedal applied

Cruise control disengagement 3rd history: Brake pedal applied

Cruise control disengagement 4th history: Brake pedal applied

Cruise control disengagement 5th history: Brake pedal applied

Cruise control disengagement 6th history: Brake pedal applied

Cruise control disengagement 7th history: Brake pedal applied

Cruise control disengagement 8th history: Brake pedal applied

Accelerator pedal position: 0 %

Starter relay command: Off

Cruise control "On"/"Off" switch: Off

Cruise control "Set/Coast" switch: Off

Cruise control "Cancel" switch: Inactive

Cruise control "Resume/Accelerate" switch: Off

Drop-Throttle status: Inactive

Drag control status: Inactive

Torque request inhibit - minimum torque: No

Torque request inhibit - fuel: No

Torque request inhibit - ignition timing: No

Torque request inhibit - TAC: No

Torque request inhibit - minimum idle: No

Cruise control inhibit reason: Brake pedal applied

Speed limiting/warning switch status: Inactive

Speed limiting/warning: Inactive

Speed limiting/warning: Inactive

Cruise control: Disabled

Cruise control switch: Undetermined state

Traction control axle torque request signal: -22534 N·m

Traction control torque request signal: -848 N·m

Torque request inhibit - TAC limit: No

Torque request inhibit - ignition timing advance: No

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition 1 signal: 0.00 V

Brake pedal position circuit signal: Released

Clutch pedal starter inhibit switch: On

Transmission inhibiting engine cranking: No

P/N switch: Inactive

Engine controls ignition relay command: Off

Ignition accessory signal: Off

Crank request signal: No

Generator F terminal signal: 0 %

Accelerator pedal position: 0 %

Starter relay control circuit high voltage test status: Malfunction

Starter relay control circuit low voltage test status: Malfunction

Starter relay command: Off

Starter relay control circuit open test status: Malfunction

Generator L - terminal command: 0 %

Engine controls ignition relay control circuit high voltage test status: Malfunction

Engine controls ignition relay control circuit low voltage test status: Malfunction

Engine controls ignition relay control circuit open test status: Malfunction

Engine controls ignition relay feedback signal: 0.0 V

Generator L-terminal circuit high voltage test status: Malfunction

Generator L-terminal circuit low voltage test status: Malfunction

Generator L - terminal command: Off

Generator L-terminal circuit open test status: Malfunction

ECM response source: Ignition switch start

ECM authentication status: Unknown

ECM challenge status: Invalid

Immobilizer security information programmed: No

Immobilizer system status: Standby

Immobilizer password learn : Inactive

Immobilizer security code accepted: No

Immobilizer security code function: Not present

Immobilizer security code programmed: No

Immobilizer security code lockout: Inactive

Immobilizer password learn scan tool delay: Inactive

Immobilizer auto learn counter: 0

Immobilizer automatic learn timer: 0 sec

MIL requested by DTC: No

Electric power management inhibit reason: None

Immobilizer valid response received time: 0 ms

Generator indicator command: Off

Power mode: Off

Ignition 1 signal: Off

Engine oil pressure: 0 kPa

Hood position: Closed

Battery voltage high resolution: 0.00 V

Low-voltage battery current: 0.00 A

Low-voltage battery temperature: -40 °C

Low-voltage battery state of function: 0.00 V

Low-voltage battery state of health: 0 %

Low-voltage battery state of charge: 0 %

Engine crank time: 0.00 sec

Immobilizer security code lockout active timer: 0 ms

Engine hood switch: Closed

Immobilizer security code programming counter: 0 Counts

Immobilizer security code reset counter: 0 Counts

VIN programing counter: 0 Counts

Distance since last oil level warning: 0 km

Distance since last oil pressure warning: 0 km

Maximum engine speed when engine overspeed detected: 0 rpm

Engine speed when engine overspeed detected: 0 rpm

Vehicle speed when engine overspeed detected: 0 km/h

Accelerator pedal position when engine overspeed detected: 0 %

Engine oil temperature when engine overspeed detected: -40 °C

Current gear when engine overspeed detected: 1

MAF when engine overspeed detected: 0.00 g/sec

Odometer when engine overspeed detected: 0 km

Engine overspeed counter: 0 Counts

Engine overspeed: Not present

Total engine overspeed time: 0 ms

Engine coolant temperature sensor: -40 °C

Vehicle speed sensor: 0 km/h

Intake air temperature sensor 1: -40 °C

Remaining fuel in tank: 0 %

Baro: 0 kPa

Misfire monitor enabled this ignition cycle: No

Misfire monitor complete this ignition cycle: Yes

Fuel system monitor enabled this ignition cycle: No

Fuel system monitor complete this ignition cycle: Yes

Component monitor enabled this ignition cycle: No

Component monitor complete this ignition cycle: Yes

Catalyst monitor enabled this ignition cycle: --

O2S/HO2S monitor enabled this ignition cycle: --

EVAP monitor enabled this ignition cycle: --

HO2S heater monitor enabled this ignition cycle: --

EGR/Camshaft position monitor enabled this ignition cycle: --

Catalyst monitor complete this ignition cycle: --

O2S/HO2S monitor complete this ignition cycle: --

EVAP monitor complete this ignition cycle: --

HO2S heater monitor complete this ignition cycle: --

EGR/Camshaft position monitor complete this ignition cycle: --

Ignition 1 signal: 0.00 V

Ambient air temperature: -40 °C

Brake pedal position circuit signal: Released

Clutch pedal: No

Cold start: No

Coolant temperature at engine start: -40 °C

Remaining fuel in tank: 0 L

Engine off time: 00:00:00

Intake air temperature sensor 1 at start: -40 °C

MIL requested by DTC: No

MIL command: Off

Calculated barometric pressure: 0 kPa

Inspection/Maintenance drive cycle complete: No

Inspection/Maintenance drive cycle vehicle speed time complete: No

Inspection/Maintenance drive cycle propulsion system active time complete: No

Inspection/Maintenance drive cycle engine speed/load time complete: No

Inspection/Maintenance drive cycle idle time complete: No

Intake air temperature sensor 2 at start: -40 °C

Check engine telltale request: No

Number of DTC: 0 Counts

Misfire monitor enabled: No

Misfire monitor complete: Yes

Fuel system monitor enabled: No

Fuel system monitor complete: Yes

Component monitor enabled: No

Component monitor complete: Yes

Catalyst monitor enabled: --

O2S/HO2S monitor enabled: --

EVAP monitor enabled: --

HO2S heater monitor enabled: --

EGR/Camshaft position monitor enabled: --

Catalyst monitor complete: --

O2S/HO2S monitor complete: --

EVAP monitor complete: --

HO2S heater monitor complete: --

EGR/Camshaft position monitor complete: --

Engine load: 0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim: -100 %

Long term fuel trim: -100 %

MAP sensor: 0 kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Intake air temperature sensor 1: -40 °C

Mass air flow sensor: 0.00 g/sec

Alternative fuel rail pressure sensor: 0 kPa

EVAP purge solenoid valve command: 0 %

Remaining fuel in tank: 0 %

Warm-ups since DTC cleared: 0 Counts

Distance since DTC cleared: 0 km

Baro: 0 kPa

Calculated catalyst temperature: -40 °C

Ignition 1 signal: 0.00 V

Air/Fuel equivalence ratio command: 0.00

Ambient air temperature: -40 °C

Target throttle position: 0 %

Current fuel type: Not available

Engine oil temperature: -40 °C

Driver requirement torque: -125 %

Extended travel brake pedal position signal: Released

Brake pedal position circuit signal: Released

Transmission inhibiting engine cranking: No

P/N switch: Inactive

Engine controls ignition relay command: Off

Ignition accessory signal: Off

Crank request signal: No

Fuel enrichment - hot catalyst: Inactive

Fuel enrichment - hot coolant: Inactive

Power enrichment: Inactive

Fuel control loop status: Open

Deceleration fuel cut-off: Inactive

Fuel trim learn: Disabled

Throttle position performance test: Ok

MAP performance test 2: Ok

MAP performance test 1: Ok

MAF performance test: Ok

Engine oil temperature calculated: -40 °C

Target idle speed: 0 rpm

Distance since first malfunction: 0 km

Distance since last malfunction: 0 km

Ignition cycles with malfunction since 1st malfunction: 0 Counts

Ignition cycles without malfunction since last malfunction: 0 Counts

Ignition cycles without completed test since 1st malfunction: 0 Counts

Throttle position: 0 %

Mass air flow sensor: 0 Hz

Accelerator pedal position: 0 %

Remaining fuel in tank: 0 L

Torque delivered signal: 0 N·m

Engine off time: 00:00:00

5V reference voltage circuit 1: 0.00 V

5V reference voltage circuit 2: 0.00 V

Engine controls ignition relay control circuit high voltage test status: Malfunction

Engine controls ignition relay control circuit low voltage test status: Malfunction

Engine controls ignition relay control circuit open test status: Malfunction

Engine controls ignition relay feedback signal: 0.0 V

Output shaft speed sensor: 0 rpm

Alternative fuel disable message: Enabled

Fuel mode request to ECM: Undetermined state

Fuel mode command from ECM: Undetermined state

MAP sensor: 0.00 V

Intake air temperature sensor 1 at start: -40 °C

Intake air temperature sensor 2: -40 °C

Barometric pressure sensor: 0.00 V

5V reference voltage circuit 4: Ok

5V reference voltage circuit 3: Ok

5V reference voltage circuit 2: Ok

5V reference voltage circuit 1: Ok

5V reference voltage circuit 3: 0.00 V

5V reference voltage circuit 4: 0.00 V

Power mode: Off

Ignition 1 signal: Off

Calculated barometric pressure: 0 kPa

Intake air temperature sensor 2: 0 Hz

Ambient humidity: 0 %

Intake air humidity sensor: 0 %

O2 sensor 1, bank 1: 0.00 V

O2 sensor 2, bank 1: 0.00 V

Hood position: Closed

Engine stopping: No

System OFF: No

Engine running: No

Engine off: No

Engine starting: No

Engine stalled: No

Engine stopped: No

Battery voltage high resolution: 0.00 V

Low-voltage battery current: 0.00 A

Low-voltage battery temperature: -40 °C

Low-voltage battery state of function: 0.00 V

Low-voltage battery state of health: 0 %

Low-voltage battery state of charge: 0 %

Intake air temperature sensor 2 at start: -40 °C

Distance this driving cycle: 0 km

Engine hood switch: Closed

A/C compressor clutch relay

Stop/Start system

Intake camshaft position actuator

Exhaust camshaft position actuator

Intake camshaft position actuator solenoid valve

Exhaust camshaft position actuator solenoid valve

Compression test

Compression test

Cooling fan test

Cooling fan relay 1

Cooling fan relay 2

Cooling fan relays 1 and 2

Engine controls ignition relay

Engine oil pressure control solenoid valve

Engine speed

Throttle position

Throttle position

Evaporative emission (EVAP) system, canister purge valve

Fuel control loop status

Cylinder power balance

Depressurize fuel system

Fuel pump relay

Fuel pump enable

Cylinder 1 fuel injector

Cylinder 2 fuel injector

Cylinder 3 fuel injector

Cylinder 4 fuel injector

Generator L terminal

Idle ignition timing

Ignition timing retard

Check engine telltale

O2 sensor 1, bank 1 heater

O2 sensor 2, bank 1 heater

Starter relay

Starter relay

Starter pinion solenoid actuator relay

Starter relay

Catalyst test