Car, CITROEN, C3 Picasso, 9HD (DV6CTED) - HDI SID807 BR2

PSA reference: 96 63 24 14 80

ECU - manufacturer: Siemens

Additional number: 96 66 68 11 80

Software version: 40 01

Software reference: 91 83 35

VIN no: Z8TND9HD8GM017685

Engine type: 9HD

Model: C4 L (B7)

U2118: Intersystems CAN. Request for principal wake-up of ECU not plausible or absent

Clear DTC

Camshaft and crankshaft synchronization: Yes

Air mixer - last initialisation value: Done

EGR valve - status of last learning: Done

Last turbo initialisation: Done

EGR valve - initialised initial position of lower limit: 22 %

EGR valve - last initialised position of lower limit: 23 %

Air mixer - initialized initial position of upper limit: 87 %

Air mixer - initialized initial position of lower limit: 13 %

Air mixer - last initialised position of upper limit: 87 %

Air mixer - last initialised position of lower limit: 13 %

Turbo - initialized initial position of upper limit: 62 %

Turbo - initialized initial position of lower limit: 34 %

Turbo - last initialised position of upper limit: 67 %

Turbo - last initialised position of lower limit: 25 %

Engine speed: 65513 rpm

High pressure fuel pump: 1.5 A

Fuel regulating valve - duty cycle: 32 %

Target fuel pressure: 297 bar

Fuel pressure - measured: 301 bar

Calculated injected flow: 5.4 mg/impulse

Injector 1 - correction value: 0.065

Injector 2 - correction value: 0.083

Injector 3 - correction value: 0.008

Injector 4 - correction value: 0.086

Fuel temperature sensor: 184 °C

Control voltage of the injectors of bank 1: 228 V

Injector - opening correction strategies activation status: Active

Injection time cylinder 1: 1.1 ms

Injection time cylinder 2: 1.0 ms

Injection time cylinder 3: 0.9 ms

Injection time cylinder 4: 0.9 ms

Engine speed: 768 rpm

Mass air flow sensor: 24 °C

Intake air temperature sensor: 31 °C

Turbo pressure: 1000 mbar

Turbo pressure - measured: 992 mbar

Barometric pressure sensor: 988 mbar

Turbo position - reference value: 90 %

Turbo position - repeat: 90 %

Air metering valve - position copy: 0 %

EGR valve - position: 22 %

EGR valve - position repeat: 22 %

EGR valve - open cycle ratio: 7.2 %

Outside air temperature: 20 °C

Turbo valve - open cycle ratio: 62 %

Target mass air flow: 193 mg/impulse

Mass air flow sensor: 193 mg/impulse

Vehicle speed sensor: 1 km/h

Cruise control system status: Inactive

Clutch pedal: Pressed

Speed limiter: Inactive

Main brake - information: Released

Brake pedal - redundant: Released

Accelerator pedal point of resistance sensor: Not exceeded

Accelerator pedal position sensor 1: 257 mV

Accelerator pedal position sensor 2: 257 mV

Accelerator pedal position sensor: 1 %

Gear transmission ratio: 1

Gearbox type: Manual

Cruise control - speed setting: 1 km/h

Speed limiter speed setting: 1 km/h

Battery voltage: 0.10 V

Supply voltage 5V N1: 257 mV

Supply voltage 5V N2: 257 mV

Supply voltage 5V N3: 257 mV

Generator: -49 °C

Power relay: Active

Oil pressure switch: Ok

Starter control: No piloting of starter motor

Additional heater: Active

Clutch pedal position sensor: 1 %

Engine coolant temperature sensor: 60 °C

Cooling fan - reference speed: 0 %

Cooling fan - speed: 0 %

Cooling fan relay 2: Not control

A/C circuit - pressure: 5.7 bar

Oil pressure: Ok

Oil level: 762 mV

Engine status: Cut off stalled

Electronic temperature - stored: 50 °C

Number of engine starts: 0

Number of restarts: 6081

Mileage of the vehicle at the last complete programming of the diesel injectors: 197112.0 km

Additional heater: Active

Engine speed: 773 rpm

Engine coolant temperature sensor: 60 °C

Cooling fan - reference speed: 0 %

Cooling fan - speed: 0 %

Cooling fan relay 2: Not control

A/C circuit - pressure: 5.7 bar

Camshaft and crankshaft synchronization: Yes

Engine speed: 1 rpm

Vehicle speed sensor: 1 km/h

Cruise control system status: Inactive

Clutch pedal: Pressed

Speed limiter: Inactive

Main brake - information: Released

Brake pedal - redundant: Released

Accelerator pedal point of resistance sensor: Not exceeded

Accelerator pedal position sensor 1: 257 mV

Accelerator pedal position sensor 2: 257 mV

Accelerator pedal position sensor: 1 %

Gear transmission ratio: 1

Gearbox type: Manual

Cruise control - speed setting: 1 km/h

Speed limiter speed setting: 1 km/h

Clutch pedal position sensor: 1 %

Starting inhibiting control - information by wire: --

Starting inhibiting control - multiplexed information: --

Engine coolant temperature sensor: 60 °C

Oil pressure: Ok

Oil level: 762 mV

Engine status: Cut off stalled

Engine speed: 1 rpm

Battery voltage: 0.10 V

Supply voltage 5V N1: 257 mV

Supply voltage 5V N2: 257 mV

Supply voltage 5V N3: 257 mV

Generator: -49 °C

Power relay: Active

Oil pressure switch: Ok

Starter control: No piloting of starter motor

Fuel temperature sensor: 184 °C

Engine speed: 768 rpm

Mass air flow sensor: 24 °C

Intake air temperature sensor: 31 °C

Turbo pressure: 1000 mbar

Turbo pressure - measured: 992 mbar

Barometric pressure sensor: 988 mbar

Turbo position - reference value: 90 %

Turbo position - repeat: 90 %

Air metering valve - position copy: 0 %

EGR valve - position: 22 %

EGR valve - position repeat: 22 %

EGR valve - open cycle ratio: 7.2 %

Outside air temperature: 20 °C

Turbo valve - open cycle ratio: 62 %

Target mass air flow: 193 mg/impulse

Mass air flow sensor: 193 mg/impulse

Engine coolant temperature sensor: 60 °C

Vehicle speed limit: Active

Electric parking brake: Ok

Uncorrected coolant temperature: 60 °C

Uncorrected air temperature: 61 °C

Generator temperature: -37 °C

Battery temperature: 50 °C

Generator voltage: 14.56 V

Battery - charge: 11.96 V

Ancillaries battery - charge: 15 %

Generator speed: 1125 rpm

Predicted reversible generator - torque reference value: 110 N·m

Torque necessary for restarting: 250 N·m

Reversible generator - actual torque: 125 N·m

Start/stop: Pressed

Neutral sensor - condition: True

Power accumulator - replacement reset: Active

Request for resetting of power storage battery - status: Active

Driver present: Present

Generator deactivation: Active

Reverse gear engaged: Yes

Clutch pedal position sensor: 16 %

Start/stop function: Precharging of the power accumulator

Stop authorised by the ECUs for the suspension and wheels: Yes

Stop authorised by the engine subsystem: No

Stop authorised by the voltage retaining device ECU: Yes

Stop authorised by the BSI ECU: Yes

Stop authorised by the transaxle ECU: Yes

Electric motor sub-assembly ECU restarting request: Yes

Suspension and wheels ECUs restarting request: Yes

Engine ECU restart request: No

Voltage retaining device ECU restarting request: No

BSI ECU restarting request: Yes

Transaxle ECU restarting request: No

Vacuum available in the braking circuit: Yes

Drive train - status: Open

Selector lever - position: M

Gear transmission ratio: Neutral

Power accumulator temperature: 80 °C

Voltage retaining device power electronics - temperature: 51.5 °C

Vacuum in the vacuum circuit: 30 mbar

Reversible generator - status: Pre-flow mode

Authorisation of restarting received by the engine ECU via the LIN: No

Authorisation of restarting sent by the engine ECU to the reversible generator: Yes

Reversible generator - reference: Cutting-out aid

Voltage retaining device - status: Discharge

Nominal state of health of the power accumulato: Yes

Voltage at terminals of the power accumulator: 1.45 V

Voltage retaining device - status: Overheating

State of health of the power accumulator: 16 %

Ancillary drive belt - replacement required: Yes

Engine - cause of not stopping: No cause of not stopping stored; No cause of not stopping stored; No cause of not stopping stored; No cause of not stopping stored; No cause of not stopping stored; No cause of not stopping stored; No cause of not stopping stored; No cause of not stopping stored

Electrical cause of engine not stopping: No cause of not stopping stored; No cause of not stopping stored; No cause of not stopping stored; No cause of not stopping stored; No cause of not stopping stored; ; ;

Reversible generator - engine restartability guaranteed: Restartability guaranteed

Convergence of state of health of the power accumulator: Converged state of health

Reversible generator - restart authorisation: Yes

Reversible generator - stop authorisation: Yes

Reversible generator - restart order: Yes

Voltage retaining device ECU - restart authorisation: Yes

Suspension and wheels ECUs restart authorisation: Yes

Mass air flow sensor: 24 °C

Intake air temperature sensor: 31 °C

Turbo pressure: 1000 mbar

Turbo pressure - measured: 992 mbar

Barometric pressure sensor: 988 mbar

Turbo position - repeat: 90 %

Air metering valve - position setting: 0 %

Air metering valve - position copy: 0 %

EGR valve - position: 22 %

EGR valve - position repeat: 22 %

EGR valve - open cycle ratio: 7.2 %

Outside air temperature: 20 °C

Turbo valve - open cycle ratio: 62 %

Target mass air flow: 193 mg/impulse

Mass air flow sensor: 193 mg/impulse

O2 sensor - mixture calculated: 0.150

O2 sensor - activation heating: 10 %

Diesel particulate filter (DPF) - soot mass: 0.084 g/l

Diesel Particulate filter (DPF) - cinder count: 84 %

Diesel Particulate filter (DPF) - distance before replacing: 10 km

Diesel Particulate filter (DPF) - differential pressure: 173 mbar

Additive tank: 963 ml

Volume of additive remaining in the reservoir: 105 ml

Quantity of additive deposited in the filter: 143 g

Diesel particulate filter (DPF) - outlet temperature: 14 °C

Authorisation of regeneration: No

Additive minimum level: Minimum level reached

Exhaust heat recovery: Active

Diesel particulate filter (DPF) - regeneration status: Active

Power consuming equipment activation request: Yes

Diesel Particulate filter (DPF) - distance since last regeneration: 204 km

Average distance between the last 10 regenerations: 796 km

Diesel particulate filter (DPF) - distance since last replacement: 120000 km

Locking of the ECU: Unlocked

Immobilizer - status: CMM matched (1st time)

Problem detected when transmitting the unlock code: No problem

Cylinder 1 injector - code: 00 5C 10 0E 0C 03

Cylinder 3 injector - code: 00 55 0A 0B 0B 05

Cylinder 4 injector - code: 00 38 08 0D 06 01

Cylinder 2 injector - code: 00 63 11 13 0C 02

No vehicle stop authorisation: 0

No power steering stopping authorisation: 0

No chassis stop authorisation: 0

Inadequate braking assistance: 0

No engine stop authorisation: 0

No electromotor subassembly stop authorisation: 15

No restart torque stop authorisation: 0

No gearbox stopping authorisation: 0

Anticipation of start/stop alert: 0

Start/stop alert: 0

Power accumulator voltage insufficient: 0

Overheating of voltage retaining device: 0

Battery - charge status insufficient: 0

No vehicle stop authorisation: 0

No power steering stopping authorisation: 0

No chassis stop authorisation: 0

Inadequate braking assistance: 0

No engine stop authorisation: 0

No electromotor subassembly stop authorisation: 16

No restart torque stop authorisation: 0

No gearbox stopping authorisation: 0

Anticipation of start/stop alert: 0

Start/stop alert: 0

Power accumulator voltage insufficient: 0

Overheating of voltage retaining device: 0

Battery - charge status insufficient: 15

No vehicle stop authorisation: 0

No power steering stopping authorisation: 0

No chassis stop authorisation: 0

Inadequate braking assistance: 0

No engine stop authorisation: 0

No electromotor subassembly stop authorisation: 16

No restart torque stop authorisation: 0

No gearbox stopping authorisation: 0

Anticipation of start/stop alert: 0

Start/stop alert: 0

Power accumulator voltage insufficient: 0

Overheating of voltage retaining device: 0

Battery - charge status insufficient: 16

Cooling fan high speed

Cooling fan low speed

Injector 1

Injector 2

Injector 3

Injector 4

Fuel flow regulator

EGR valve

Air mixer

O2 sensor heating

Power supply relay

Pre-post heating relay control

Additional heating

Starter motor control relay

Turbocharger actuator

EGR exchanger bypass

Intake air pressure

Checking engine setting

Mass air flow sensor test

EGR circuit checking

Exhaust heat recovery valve checking

Checking the functioning of the air circuit assembly

Manifold inlet pressure sensor checking

High Pressure pump replacement

Fuel flow regulator replacement

EGR valve replacement

EGR exchanger replacement

Air mixer replacement

Turbocharger replacement

Mass air flow sensor replacement

Engine block without Mass air flow replacement

Engine block with Mass air flow replacement

Replacement of the diesel additive reservoir, of the pump or of the pipes

DPF replacement

Filling of the additive reservoir or pouch

O2 sensor replacement

Ancillary drive belt replacement

Exhaust manifold replacement

Cylinder head replacement

Clutch with proportional sensor replacement

Injector adaptives

Resetting the health condition of the energy accumulator

DPF regeneration (vehicle stationary)

Injectors replacement