Car, CITROEN, C4 Picasso, BVA AM6

Transaxle - BVA AM6 - 0

Identification

PSA reference: 96 64 87 09 80

ECU manufacturer: Magneti Marelli

Additional number: 96 66 16 17 80

Diagnostic version: 00

Calibration version: FF FF

Software version: 08 01

Emission: Not defined

ECU production date: --

Software reference: 59 63 25

DTC

P0731: Gear 1 incorrect range/performance

Controls

Clear DTC

Data stream

Engine stalling not linked with converter lock-up: Yes

Engine stalling linked with converter lock-up: Yes

Number of stalling clearing cycles: 18 %

Gear selected: Intermediate P/R

Gear engaged: 4

Torque converter: Converter in regulation or sliding

Sport mode switch: Released

Snow mode switch: Released

Accelerator pedal position sensor: 17.5 %

Reduction of torque requested by the automatic gearbox: 64.0 N·m

Engine torque requested by the driver: 408.0 N·m

Torque reference value requested by the automatic gearbox: 378.1 N·m

ASR/ESP in regulation mode: Yes

Request for switching on of the emission control fault warning light (MIL lamp): No

Request for switching on of an automatic gearbox overheating warning light: Yes

Secondary brake switch: Closed

Oil change required: Yes

Main brake switch: Closed

RCD reawakening: Main

Front wheels average speed: 0.0 rpm

Right rear wheel speed sensor: 0.0 km/h

Left rear wheel speed sensor: 223.8 km/h

Front wheels average speed: 0.0 km/h

A/T oil temperature: -38 °C

Battery voltage: 12.10 V

Outside air temperature: 32.5 °C

Engine speed: 4.5 rpm

Actual engine torque: 48.0 N·m

Engine coolant temperature sensor: 88 °C

Control of the "S2" solenoid valve (Management of the engine break): Requested by inactive

Control of the "S1" solenoid valve (Management of the engine break): Not defined

Control current SLU: 350 mA

Return current (measurement) SLU: 50 mA

Electrical status of the solenoid valve SLU:

Control current SLT: 200 mA

Return current (measurement) SLT: 320 mA

Electrical status of the solenoid valve SLT: Controlled

Control current SLB1: 1820 mA

Return current (measurement) SLB1: 1920 mA

Electrical status of the solenoid valve SLB1: Invalid

Control current SLC1: 100 mA

Return current (measurement) SLC1: 960 mA

Electrical status of the solenoid valve SLC1: Activated

Control current SLC2: 800 mA

Return current (measurement) SLC2: 1280 mA

Electrical status of the solenoid valve SLC2: Activated

Control current SLC3: 40 mA

Return current (measurement) SLC3: 1600 mA

Electrical status of the solenoid valve SLC3: Invalid

A/T input speed: 192 rpm

A/T input speed calculated: 128 rpm

A/T output speed: 0 rpm

A/T output speed (recommended): 0 rpm

Converter sliding speed: -8128.0 rpm

Converter sliding speed (theoretical value): 1152.0 rpm

Declutch when stationary: Not defined

Intermittent switching to emergency (refuge) mode: No

Automatic gearbox in emergency mode (refuge): Yes

Operating pattern used by automatic gearbox: Minimum operation

Key locking control (key - lock): Locked

Status RCD line: Active

Gear decrease (-): Inactive

Cruise control: Activated or effective

Gear increase (+): Inactive

Starting inhibiting control ( start Lock ): Activated

Oil counter read

Oil wear counter: 10000

Actuators test

Controls

Shift solenoid valve 1/A

Shift solenoid valve 2/B

Solenoid valve SLT

Solenoid valve SLB1

Solenoid valve SLC1

Solenoid valve SLC2

Solenoid valve SLC3

Solenoid valve SLU

Shift lock solenoid

Control of the starting prevention (Start Lock)

Key locking control (key Lock)

Utility

Controls

Programming of neutral position

Replacement of the automatic gearbox oil

Oil wear counter