Bil, RENAULT, TWINGO III, H4D - Petrol (INJ)

Program number: 34 4D

Softwareversion: 45 00

Kalibreringsnummer: 43 80

MPR reference: 23710-4034R

Electronic version: 23710-2575R

Diagnose version: 44

Supplier: 153

Stel nr.: X7LHSRDVN51262429

DF080 [CC.0]: Camshaft position actuator - circuit short to ground

Clear DTC

Motor kølevæske temperatur føler: 80.0 °C

Motor Hastighed: 0 Omdr.

Køretøjs hastighed : -- km/h

Motordrejningsmoment: -- N·m

ECU supply voltage: -- V

Barometrisk tryk føler: -- mbar

Speeder pedal positions føler N1: -- mV

Speeder pedal position N2: -- mV

A/C pressure: -- V

Computer + after ignition: --

Braking detected multiplexed signal: --

Gross engine torque: -- N·m

Motor: --

Camshaft /TDC synchronization: --

Crankshaft synchronization: --

AC compressor: --

Sensor supply 1: -- V

Sensor supply 2: -- V

Sensor supply 3: -- mV

Target idle speed: -- Omdr.

Wired brake contact: --

Startspærre: --

Gaspedalposition: -- %

Inlet camshaft dephaser setpoint: --

Inlet camshaft dephaser: --

Inlet camshaft shifter control duty cycle: -- %

Cruise control setting: -- km/h

Brake/accelerator pedal inconsistency: --

RV/LV button voltage: -- V

CC/SL connection after CC button pressed: --

CC/SL connection after SL button pressed: --

Hastighedsbegrænser: --

First start: --

Starting: --

Fan unit high speed final request: --

Fan unit low speed final request: --

Cruise control/speed limiter buttons: --

Cruise control/speed limiter function: --

Cruise control operating reliably: --

Actual vehicle speed info absent: --

Actual vehicle speed info unavailable: --

Automatic gearbox in defect mode: --

Change of vehicle speed unit: --

Displayed vehicle speed info absent: --

Displayed vehicle speed unavailable: --

SL inhibited by injection: --

Vehicle speed consistency: --

Automatic gearbox in defect mode: --

Brake information absent: --

Brake information unavailable: --

Clutch information absent: --

Clutch information unavailable: --

Cruise control info monitoring: --

Cruise control inhibited by injection: --

Deceleration without brake depressed: --

Sharp decel. without brake depressed: --

Vehicle speed displayed: -- km/h

Vehicle speed displayed: --

Generator power: -- W

Idle speed regulation: --

Fast idle speed: -- Omdr.

Clutch contact wire connection: --

Brake switch: --

CC/SL deactivation by driver action: --

Fartpilot: --

Parking brake: --

Reverse gear engaged: --

Starter button: --

Traction control/ Anti-yaw control: --

Duration of "Resume" button press: -- sek

Duration of "+" button press: -- sek

Duration of "-" button press: -- sek

Duration of "Suspend" button press: -- sek

Number of abnormal CC/SL transitions: --

Impact detected: --

A/C authorisation: --

Engine speed required by A/C: -- Omdr.

Generatorbelastning: -- %

Idle adaptive correction: -- N·m

Mastervac pressure: -- mbar

Richness regulation programming offset: --

Richness regulation programming gain: --

Richness regulation programming offset: -- µs

Number of engine rotation: --

Cranking signal: --

Crankshaft synchronisation loss counter: --

Number of starting cycles: --

Auto emergency braking system request: --

Change of vehicle speed unit: --

Stop warning light: --

Maximum vehicle speed: -- km/h

Flywheel target programming: --

Last adaptive value programmed: --

Clutch contact multiplex signal: --

Vehicle speed multiplexed information: --

Vehicle speed displayed: --

A/C command: --

Refrigerant pressure: -- bar

Manual or assisted parking brake: --

Clutch start of travel wiring switch: --

Koblingspedalkontakt: --

Manual gearbox lever in neutral: --

CC/SL connection authorisation: --

Solenoid valve programming inlet camshaft dephaser: --

Idle regulation integral correction: -- N·m

Coolant flow valve control: --

Ladetryk: -- mbar

Intake air pressure: -- mbar

Boost pressure reference value: -- hPa

Inlet flap control: -- %

MAP føler: -- mbar

Throttle position sensor reference value: -- %

Gasspjældpositionsføler 1: -- %

Gasspjældpositionsføler 2: -- %

Gasspjældpositionsføler 1: -- mV

Gasspjældpositionsføler 2: -- mV

Luft masse måler: -- kg/h

Gasspjælds positions føler: -- %

Intake air temperature sensor: -- °C

Pressure before turbine: -- mbar

O2 sensor 1, bank 1 heater duty cycle: -- %

O2 sensor 2, bank 1 heater duty cycle: -- %

Damper valve upstream temperature: -- °C

Throttle actuator at lower mechanical stop: -- %

Programming throttle limits: --

Boost pressure wastegate control: -- %

Delay before O2 sensor 1, bank 1 heating: --

Throttle valve safe mode value programmed: -- %

Linearised manifold pressure: -- mbar

MAP føler: -- mbar

Turbocharger pressure wastegate duty cycle: -- %

O2 sensor 1, bank 1 heater: --

O2 sensor / Lambda sonde 2, bank 1 Varme element: --

Proportional richness sensor: --

Calculated manifold absolute pressure: -- hPa

Turbo position setting: -- %

Turboladerwastegateventil: -- %

First offset damper valve closed: --

Cooling request by injection: --

Injection time: -- µs

Ignition advance angle: -- °CRK

Flow rate function: --

Kommando til brændstofpumperelæ: --

Canister bleed solenoid valve RCO: -- %

Cylinder 1 combustion misfire counter: --

Cylinder 2 combustion misfire counter: --

Cylinder 3 combustion misfire counter: --

Knock signal cylinder 1: --

Knock signal cylinder 2: --

Knock signal cylinder 3: --

Average knock signal: --

Richness regulation: --

Richness correction: -- %

Fuel pump priming complete: --

Controlled coolant thermostat duty cycle: -- %

Richness correction value: --

Operating richness adaptive: --

Combustion misfire counter: --

Alcohol fuel adaptive correction: -- %

Operating richness adaptive: --

Lambda value: --

Target gearbox ratio: --

Gear transmission ratio: --

Rough turbocharging pressure: -- hPa

Lambda value: --

Lambda sonde / O2 sensor 1, bank 1: --

Indsprøjtnings dyse 1

Indsprøjtnings dyse 2

Indsprøjtnings dyse 3

Fuel pump

Evaporative emission (EVAP) system, canister purge valve

Ignition coil 1

Ignition coil 2

Ignition coil 3

Camshaft dephaser: solenoid valve slide movement

Coolant flow valve control

Piloted oil pump

Cooling fan low speed

Cooling fan high speed relay

A/C relay

Air inlet control flap on front end panel

Boost pressure wastegate

Electric water pump

Bypass solenoid valve control valve

Camshaft shifter: setpoint monitoring test

V036 Fuel supply prevention

V010 Rediger stel nr.

V342 Vacuum pump operation request

V386 Vacuum pump operation request

R003 ECU learn reset

R047 Cruise control/speed limiter programming