Bil, RENAULT, CLIO III, F4R - Petrol (INJ)

Electronic version: 32 35 37 35 52

Program number: 34 A7

Softwareversion: 45 00

Kalibreringsnummer: 43 80

MPR reference: 34 30 33 34 52

Diagnose version: 48

Supplier: 153

Stel nr.: X7LHSRDVN51262429

DF089 [2.DEF]: Manifold absolute pressure (MAP) sensor - incorrect signal

Clear DTC

Idle regulation reference: 0 Omdr.

Korrektion af tomgangshastighed: 0 Omdr.

Køretøjs hastighed : 0 km/h

Ladetryk: 103 mbar

Ignition advance angle: -24 °CRK

Knock correction: 0.0 °CRK

Turbocharger valve duty cycle: 0 %

ECU supply voltage: 8.00 V

Motor kølevæske temperatur føler: -40 °C

Air temperature: -40 °C

MAP føler: 103.0 mbar

Barometrisk tryk føler: 1047 mbar

Motor Hastighed: 0 Omdr.

Pedal no load and throttle closed: Ikke registreret

Accelerated idle request: Absent

Actuator relay control: Inaktiv

Fan 1 control status: Sluk

Fan 2 control status: Sluk

Brændstofpumpe: Inaktiv

Canister purge control: Inaktiv

O2 sensor 1, bank 1 heater: Inaktiv

O2 sensor / Lambda sonde 2, bank 1 Varme element: Inaktiv

Camshaft position actuator: Inaktiv

A/C authorisation: Nej

Gaspedalposition: -- %

No load value programmed: -- %

Throttle lower limit after offset applic.: -- %

Electronic throttle control (ETC) position corrected value : -- %

Electronic throttle control (ETC) corrected position setting: -- %

Gasspjældpositionsføler 1: -- %

Gasspjældpositionsføler 2: -- %

Throttle actuator at lower mechanical stop: -- %

Electronic throttle control (ETC) high stop programmed value: -- %

Richness autoadaptive offset: --

Richness autoadaptive gain: --

Theoretical idle regulation RCO: -- %

Richness correction: -- %

Inlet camshaft dephaser position reference value: -- °CRK

Inlet camshaft shifter control duty cycle: -- %

Camshaft shifter measured position: -- °CRK

Injection time: -- ms

Canister bleed solenoid valve RCO: -- %

Idle regulation programming value: -- %

Intake camshaft position actuator, bank 1: --

Lambda sonde / O2 sensor 1, bank 1: -- mV

Lambda sonde / O2 sensor 2, bank 1: -- mV

Motordrejningsmoment: -- N·m

Driver`s wishes estimated engine torque: -- N·m

Torque used by A.T. converter: -- N·m

Resistance engine torque transmitted on CAN: -- N·m

Misfire cylinder 1: --

Flywheel target programming: --

Cylinder 1 recognition: --

Idle rpm control: --

Programming throttle limits: --

Richness loop through upstream sensor: --

Flywheel signal: --

Air conditioner: --

Oil vapour anti-icing resistance: --

Idle regulation integral correction: -- %

Power absorbed by the AC compressor: -- W

Instantaneous fuel consumption: -- L/h

Torque lapse: -- N·m

Code programmed: Nej

Startspærre: Inaktiv

Impact detected: Inaktiv

Refrigerant pressure: -- bar

A/C request: --

Number of PC heating resis. fixed: --

RCH CUT-OUT: --

Starting: --

Brake pedal switch 2: --

Cruise control setting: -- km/h

Brake pedal switch 1: --

Turbocharger control solenoid valve

Brændstofpumperelæ

Electronic throttle control (ETC)

Evaporative emission (EVAP) system, canister purge valve

O2 sensor 1, bank 1 heating

O2 sensor 2, bank 1 heating

V010 Rediger stel nr.

V013 Injector control lock

V008 Injector control unlock

R005 Programmed values