Bil, RENAULT, CLIO II, F8Q - Diesel (INJ)

Electronic version: 32 35 37 35 52

Program number: 34 D3

Softwareversion: 45 00

Kalibreringsnummer: 43 80

MPR reference: 34 30 33 34 52

Diagnose version: 44

Supplier: 153

Stel nr.: X7LHSRDVN51262429

DF092 [CO]: O2 sensor 1, bank 1 - circuit open

Clear DTC

Idle speed reference: 0 Omdr.

Køretøjs hastighed : 0 km/h

Ignition advance angle: -24 °CRK

Knock correction: 0 °CRK

Motor kølevæske temperatur føler: -- °C

Intake air temperature sensor: -40 °C

MAP føler: 103 mbar

Motor Hastighed: 0 Omdr.

Computer + after ignition: Missing

Pedal no load and throttle closed: Nej

Check engine telltale request from transmission control module: Nej

Actuator relay control: Inaktiv

Kommando til brændstofpumperelæ: Inaktiv

Canister purge control: Inaktiv

O2 sensor 1, bank 1 heater: Inaktiv

O2 sensor / Lambda sonde 2, bank 1 Varme element: Inaktiv

Gaspedalposition: -- %

Speeder pedal positions føler N1: -- V

Speeder pedal position N2: -- V

No load position programming value: -- %

Mass or volume air flow sensor estimated value: -- kg/h

Electronic throttle control (ETC) throttle position 1 upper stop: -- V

Electronic throttle control (ETC) throttle position 2 upper stop: -- V

Electronic throttle control (ETC) throttle position 1 lower stop: -- V

Electronic throttle control (ETC) throttle position 2 lower stop: -- V

Throttle lower limit after offset applic.: -- %

Gasspjælds positions føler: -- %

Electronic throttle control (ETC) position corrected value : -- %

Electronic throttle control (ETC) corrected position setting: -- %

Speeder pedal positions føler N1: -- %

Speeder pedal position N2: -- %

Gasspjældpositionsføler 1: -- %

Gasspjældpositionsføler 2: -- %

Throttle actuator at lower mechanical stop: -- %

Electronic throttle control (ETC) high stop programmed value: -- %

Gasspjældpositionsføler 1: -- V

Gasspjældpositionsføler 2: -- V

Richness autoadaptive offset: --

Richness autoadaptive gain: --

Theoretical idle regulation RCO: -- %

Richness correction: -- %

Injection time: -- ms

Canister bleed solenoid valve RCO: -- %

Idle regulation programming value: -- %

Average knock signal: --

Lambda sonde / O2 sensor 1, bank 1: -- mV

Lambda sonde / O2 sensor 2, bank 1: -- mV

Distance since check engine telltale on (OBDII): -- km

Flywheel target programming: --

Cylinder 1 recognition: --

Double richness loop : --

Idle rpm control: --

Programming throttle limits: --

Richness regulation: --

Flywheel signal: --

Immobilizer code programmed: Nej

Startspærre: Inaktiv

Impact detected: Inaktiv

Refrigerant pressure: -- bar

A/C authorisation: --

A/C request: --

Accelerated idle request: --

Air conditioner: --

Cooling fan high speed request: --

Cooling fan low speed request: --

Number of PC heating resis. fixed: --

RCH CUT-OUT: --

Power absorbed by the AC compressor: -- W

Starting: --

Motor: --

Brake pedal switch 2: --

Cruise control setting: -- km/h

Brake pedal switch 1: --

AC air heater resistor management: --

Traction control: --

Lambda sonde / O2 sensor 1, bank 1: --

Lambda sonde / O2 sensor 2, bank 1: --

OBD warning light control: --

Vehicle transmission type: --

Vehicle speed connection type: --

Air conditioner: --

Brændstofpumperelæ

Electronic throttle control (ETC)

Evaporative emission (EVAP) system, canister purge valve

O2 sensor 1, bank 1 heating

O2 sensor 2, bank 1 heating

Static test of actuators

V010 Rediger stel nr.

V013 Injector control lock

V008 Injector control unlock

R005 Programmed values