Bil, PEUGEOT, 508, RHH - DCM3.5 BR2

PSA reference: 96 66 91 25 80

ECU manufacturer: VDO

Additional number: 96 66 91 25 80

Softwareversion: 05 00

Software reference: 79 05 58

P0487: Exhaust gas recirculation (EGR) valve stuck open

P1499: Air metering valve position incorrect (too open), After Sales

Clear DTC

Condition of neutral sensor: FALSK

Clutch pedal: 220 %

Status limit vehicle speed: Aktiveret

EGR valve high limit initial programming: 88 %

Last initialised position of EGR valve lower limit: 17 %

EGR valve high limit last programming: 2 %

EGR valve low limit last programming: 14 %

Initialised initial position of the air mixer upper limit: 96 %

Initialised initial position of the air mixer lower limit: 14 %

Locking of the ECU: Låst

Last initialised position of the air mixer upper limit: 94 %

Last initialised position of the air mixer lower limit: 10 %

Initialised initial position of the turbo upper limit: 69 %

Initialised initial position of the turbo lower limit: 3 %

Last initialised position of turbo upper limit: 10 %

Last initialised position of turbo lower limit: 10 %

Statspærrestatus: After-sales status

Problem detected when transmitting the unlock code: The programming status of the engine immobiliser cannot be read

Motor status: Self-powered starting

Camshaft and crankshaft synchronization: Nej

Mixer programming status: Not carried out

EGR valve learning status: Done

Turbo learning: Not carried out

First initialisation of the air mixer: Done

Status of first learning of EGR valve: Not carried out

First initialisation of the turbo: Done

Fuel flow regulator: 0 %

Target fuel pressure: 0 bar

Fuel pressure measured: 0 bar

Injected flow measured: 0.0 mg/impulse

Motor Hastighed: 0 Omdr.

Brændstoftemperaturføler: -50 °C

Injector opening correction strategies activation status: Inaktiv

Injection time cylinder 1: 0.0 ms

Injection time cylinder 3: 0.0 ms

Injection time cylinder 4: 0.0 ms

Køretøjets hastighed sensor: 0 km/h

Injection time cylinder 2: 0.0 ms

Fuel flow regulator: 0.0 mA

Gaspedalposition: 0 %

Measured turbo pressure: 465 mbar

Barometrisk tryk føler: 52 mbar

Turbo position setting: 18 %

Turbo position repeat: 25 %

Mixer position reference value: 10 %

Mixer position repeat: 26 %

Air flow sensor air temperature: 195 °C

Inlet air temperature at manifold: -7 °C

Turbocharging pressure reference value: 175 mbar

Gear transmission ratio: 1

Gearbox type: Manuelt

Cruise control speed setting: 1 km/h

Speed limiter speed setting: 1 km/h

Generator progressive charge reference: 1 %

Batteri spænding: 0.10 V

Supply voltage 5V N1: 257 mV

Clutch pedal: Nedtrykket

Status for fartpilotsystem: Inaktiv

Principal brake pedal: Udløst

Hastighedsbegrænser: Inaktiv

Brake pedal redundant: Udløst

Accelerator pedal point of resistance sensor: Not exceeded

Speeder pedal positions føler N1: 257 mV

Speeder pedal position N2: 257 mV

A/C circuit pressure: 1.0 bar

Oil pressure: OK

Oil level: 24 mV

Motor kølevæske temperatur føler: -40 °C

Cooling fan reference speed: 27 %

Køleventilatorhastighed: 12 %

Fan speed 2 setting:

Cylinder 1 injector code: SP9A547HT2P9LPWMEK11

Cylinder 2 injector code: BP5A8T9462P9KRU52AWZ

Cylinder 3 injector code: B77A4TRHJES9KRUM6F10

Cylinder 4 injector code: HP5A8T93A2P8L8U4T8X0

Motor Hastighed: 0 Omdr.

Air flow sensor air temperature: 195 °C

Inlet air temperature at manifold: -7 °C

Mixture calculated by the O2 sensor: 0.010

Activation heating O2 sensor: 10 %

Diesel Particulate filter (DPF) soot mass: 35.3 g/l

Diesel Particulate filter (DPF) cinder count: 10 %

Diesel Particulate filter (DPF) distance before replacing: 46 km

Diesel Particulate filter (DPF) differential pressure: 65199 mbar

Additive tank: 10 ml

Volume of additive remaining in the reservoir: 23 ml

Quantity of additive deposited in the filter: 1 g

Diesel Particulate filter (DPF) temperature: 273 °C

Authorisation of regeneration: Nej

Additive minimum level: Not reached

Diesel Particulate filter (DPF) regeneration status: Inaktiv

Power consuming equipment activation request: Nej

Diesel Particulate filter (DPF) distance since last regeneration: 257 km

Average distance between the last 10 regenerations: 10 km

Short term regeneration capacity: 15 %

Long term regeneration capacity: 10 %

Batteri spænding: 0.10 V

Cooling fan high speed

Cooling fan low speed

Indsprøjtnings dyse 1

Indsprøjtnings dyse 2

Indsprøjtnings dyse 3

Indsprøjtnings dyse 4

Fuel flow regulator

Pre-post heating relay control

Power supply relay

Turbocharger actuator

EGR exchanger bypass

Checking pressurisation of air entering the engine

Manifold inlet pressure sensor checking

Checking engine setting

Air flow circulation

EGR circuit checking

Checking the functioning of the air circuit assembly

EGR-ventil

O2 sensor heating

Heater matrix water pump: Activation

Additive pump

Exhaust heat recovery valve checking

DPF regeneration (vehicle stationary)

Filling of the additive reservoir or pouch

Replacement of the diesel additive reservoir, of the pump or of the pipes

DPF replacement

Differential pressure sensor replacement

EGR valve change

EGR exchanger replacement

Turbocharger replacement

Mass air flow sensor replacement

High Pressure pump replacement

Flow regulation valve replacement

Fuel rail pressure sensor replacement

O2 sensor replacement

Change of engine ECU without the MAF

Change of engine ECU with the MAF

Ancillary drive belt replacement

Exhaust manifold replacement

Cylinder head replacement

Initialization

Injectors replacement