Car, OPEL, Speedster, 2006, Z20LET - Motronic ME1.5.5

VIN no: W0L0TGF7532268074

Part number alpha code: 55352933 TM

Hardware number: BOS 01120261206074

Software number: 1037366915

Software version: 3378

Existing ECU type approval no: B03018

System: Z20LET

Repair shop code or tester serial number:

Programming date: 20 03 05 28

Identifier: 12 32

Vehicle manufacturer specific: 11130302

Vehicle manufacturer specific: 0532

Vehicle manufacturer specific: 0000000000

U2108 [4]: Lost communication with anti-lock brake system (ABS) control module

Clear DTC

Cooling fan relay 1: Off

Power supply relay: Off

Fuel pump relay: Off

Normal engine operating temperature: Not active

Throttle position sensor: Part load

Knock control (B1): Off

O2 sensor 1, bank 1 loop control: Open

Evaporative emission (EVAP) system, canister purge valve: Off

Air/Fuel ratio sensor 1, bank 1: Lean

O2 sensor 1, bank 1 heater: Off

Air/Fuel ratio sensor 2, bank 1: Lean

O2 sensor 2, bank 1 heater: Off

Accelerator pedal position at idle position: Not active

Idle speed offset: Not active

Check engine telltale: Off

Service vehicle soon telltale: Off

Electronic throttle control (ETC) limp home mode: Not active

A/C relay: Off

A/C information switch: Off

A/C cut-off mode: Ok

Brake pedal switch 2: Not active

Clutch pedal switch: Not active

Vehicle speed in cruise control range: Not active

Cruise control tip switch: Not active

Brake pedal switch 1: Not active

Cruise control: Not active

Battery voltage: 0 V

Engine speed: 0 rpm

Target idle speed: 0 rpm

Vehicle speed sensor: 0 km/h

Acceleration sensor: 0 m/s²

Engine coolant temperature sensor: 0.00 V

Engine coolant temperature sensor: -40 °C

Intake air temperature sensor: 0.00 V

Intake air temperature sensor: -40 °C

Mass air flow sensor: 0.00 V

Mass air flow sensor: 0 kg/h

Accelerator pedal position sensor 1: 0.00 V

Accelerator pedal position sensor 2: 0.00 V

Calculated accelerator pedal position: 0 %

Throttle position sensor 1: 0.00 V

Throttle position sensor 2: 0.00 V

Calculated throttle position: 0 %

Evaporative emission (EVAP) system, canister purge valve: 0 %

Fuel level sensor: 0.00 V

Fuel level sensor: 0 L

Ignition dwell time: 0 ms

Injection time bank 1: 0 ms

Ignition angle: -64 °

A/C pressure sensor: 0 kPa

Knock sensor signal (B1): 0 V

Knock retard angle cylinder 1: 0 °

Knock retard angle cylinder 2: 0 °

Knock retard angle cylinder 3: 0 °

Knock retard angle cylinder 4: 0 °

Short term fuel trim bank 1: -100 %

O2 sensor 1, bank 1: 0.000 V

O2 sensor 2, bank 1: 0.000 V

Long term fuel trim bank 1: -100 %

Electronic throttle control (ETC) learn counter: 0

Relative engine load: 0 %

Boost pressure sensor: 0 kPa

Barometric pressure sensor: 0 kPa

Boost pressure solenoid valve - duty cycle: 0 kPa

Additional cooling pump: Not active

Turbocharger bypass solenoid: Not active

Boost pressure command: 0 kPa

Immobilizer function programmed: Yes

Security wait time: Not active

Fuel pump relay

Ignition coil

Evaporative emission (EVAP) system, canister purge valve

Electronic throttle control (ETC)

Boost pressure valve

Turbocharger bypass solenoid

A/C relay

Additional cooling pump

Cooling fan relay 1

Check engine telltale

Service vehicle soon telltale

Evaporative emission (EVAP) system, canister purge valve

Electronic throttle control (ETC)

Idle rpm control

Injectors

Reset O2 loop block learn map

ECU learn reset

Edit configuration

Edit CAN configuration