Bil, NISSAN, PATHFINDER Hybrid (HR52), 2017-, Australia , New Zealand, Gear , Transmission

transakse - Gear / Transmission - 0

Identifikation

Dele nummer: 31036-1HH8A

Diagnostic ID: 34

Supplier number: 41 06 04

Hardware number: 00 04 70 00 04

Software nummer: 28 00

Udgavenummer: 00 00

Kalibreringsnummer: 00 14

Dele nummer: 31036-1HH8A

Manufacturer identification code reprogramming: 4

Supplier number reprogramming: 31 48 48

CRC value: --

Number of reprogramming: 50

Fejlkoder

P0746: Pressure control solenoid valve 1/A - range/performance

Controls

Clear DTC

Levende Data

CVT-B: 0

CVT-A: 0

Køretøjets hastighed sensor: 0 km/h

ESTM VSP SIG: 0 km/h

Køretøjs hastighed : 0 km/h

Speeder pedal positions føler N1: 0.0 °

Secondary pressure: 0.0 MPa

Primary pressure sensor: 0.0 MPa

A/T oil temperature: -40 °C

Line pressure: 0.0 MPa

Target primary pressure: 0.0 MPa

Target select pressure: 0.0 MPa

Target secondary pressure: 0.0 MPa

Position "L" switch status: Sluk

"DS" position switch: Sluk

Sportsprogramkontakt: Sluk

ECO mode switch: Sluk

Shift indicator signal: Sluk

"Sport" indicator: Sluk

Manual mode gear signal: Sluk

DS range signal: Sluk

ECO mode signal: Sluk

Range: D

Gear lever position - manual: 1

Engine brake level: Tænd

Kørselsmodus: Normal

Electric oil pump duty: 0 %

Electric oil pump duty monitor: 0 %

Number and type of driven axles: Tohjulstræk

Primary speed sensor: 0 Omdr.

Secondary speed sensor: 0 Omdr.

Signal for motoromdrejningstal: 0 Omdr.

Secondary pressure sensor: 0.00 V

Primary pressure sensor: 0.00 V

Gearolietemperaturføler: 0.00 V

VIGN sensor: 0.00 V

PVIGN VOLT: 0.00 V

Primary speed: 0 Omdr.

Secondary speed: 0 Omdr.

Motor speed: 0 Omdr.

Pulley gear ratio: 0.0000

G speed: 0.0 g

Engine torque recognized by TCM: 0.0 N·m

Primary torque: 0.0 N·m

Target primary speed: 0 Omdr.

Target pulley gear ratio: 0.0000

Solenoid clutch valve 1: 0.000 A

Line pressure control solenoid valve output: 0.000 A

Primary solenoid: 0.000 A

Secondary solenoid: 0.000 A

Select solenoid current: 0.000 A

Clutch 1 solenoid monitor: 0.000 A

Line pressure control solenoid valve monitor: 0.000 A

Primary solenoid monitor: 0.000 A

Motor torque: 0.0 N·m

P position SW: Sluk

Position "R" switch status: Sluk

Position "N" switch status: Sluk

Position "D" switch status: Sluk

Idle speed position switch: Sluk

Brake switch: Sluk

Up shift switch: Sluk

Down shift switch: Sluk

Manual mode: Sluk

No manual mode: Sluk

Lever up switch: Sluk

Lever down switch: Sluk

Tow mode switch: Sluk

CVT lamp: Sluk

TCS on: Sluk

ABS on: Sluk

VDC on: Sluk

ABS fail signal: Sluk

ECO mode: Sluk

Sportsprogram: Sluk

Snow mode: Sluk

Normal mode: Sluk

Electric oil pump relay monitor: Sluk

Electric oil pump relay: Sluk

CAN diagnostic support monitor

Bus off diagnostic: 83

Transmit diag: 0

ECM: 0

VDC/TCS/ABS: 0

Instrument: 0

BCM/SEC: 0

HVAC: 255

MC: 255

EV/HEV system: --

Calibration data

Unit CLB ID1: 00 10

Unit CLB ID2: 00 12

Unit CLB ID3: 00 44

Unit CLB ID4: 00 50

Unit CLB ID5: 08 75

Unit CLB ID6: 05 46

Unit CLB ID7: FA D1

Unit CLB ID8: 87 12

Unit CLB ID9: FF A1

Unit CLB ID10: 45 12

Unit CLB ID11: 12 35

Gain LU: -26299

Gain PL: -172

Gain PRI: 22424

Gain HC/RB: 4354

Gain L/B: 30100

Offset LU: -26745

Offset PL: 4712

Offset PRI: 2199

Offset HC/RB: 26708

Offset L/B: -31199

MAP NO LU: 21

MAP NO PL: 54

MAP NO PRI: 02

MAP NO HC/RB: 15

MAP NO L/B: 09

Offset 2 LU: -121

Offset 2 PL: -95

Offset 2 PRI: -122

Offset 2 H/R: -15

Offset 2 L/B: -104 A

Init offset H/R A: 23639

Init offset H/R B: 5376

Init offset H/R C: 8816

Init offset H/R D: 13700

Init offset H/R E: 1364

Init offset H/R F: 13443

Init offset LB A: 12884

Init offset LB B: 2132

Init offset LB C: 1330

Init offset LB D: 0

Init offset LB E: 0

Init offset LB F: 0

Init offset select E: 0

Init offset select F: 0

Init offset select G: 0

Select initialize learn: 00

LU initialize learn: 00

Select initialize temperature: 00

LU initialize temperature: 00

Select initialize ND pressure: 00

Select initialize ND time: 00

Select initialize NR pressure: 00

Select initialize NR time: 00

LU initialize learn 1: 0

LU initialize learn 2: 0

Udgangs test

Controls

CVT oil cooler fan circuit

Muligheder

Controls

Conform CVTF deterioration

Erase learning value