Bil, MITSUBISHI, EK-SPACE (B1), 2015, DBA-B11A, HXTSXZ1, 3B20 (0.66, D4, MPI, VVT, Auto Stop & Go(AS&G)) - MPI, GDI, DIESEL

3B20 (0.66, D4, MPI, VVT, Auto Stop & Go(AS&G)) - MPI/GDI/DIESEL - 0

Identifikation

Identificere : 00 00

ECU origin: 04

Supplier number: 85

ECU ID: 00

Diagnose version: 00

Hardware version nummer: 00 00

Softwareversion: 04 01 76

Dele nummer: 1860A029

Software nummer: 1860B05003

VIN no (original): JMBLYV98W7J007862

Class: YV

Model: Pajero / Montero V8/V9

Type: V98W

Model year: 2007

Stel nr.: JMBLYV98W7J007862

Calibration ID: 1860B0500300

Calibration verification number (CVN): FF FF FF FF

Fejlkoder

U1102: Lost communication with ABS/TCL/ASC control module

Controls

Clear DTC

Levende Data

Fuel system status A:OL: Nej

Fuel system status A:CL-Fault: Nej

Fuel system status A:CL: Nej

Fuel system status A:OL B2: Nej

Fuel system status A:OL-Drive: Nej

Fuel system status A:OL-Drive B2: Nej

Fuel system status A:OL-Fault: Nej

Fuel system status A:OL-Fault B2: Nej

Fuel supply system bank 1: N/A

Fuel system status B:OL: Nej

Fuel system status B:CL-Fault: Ja

Fuel system status B:CL: Nej

Fuel system status B:OL B2: Nej

Fuel system status B:OL-Drive: Nej

Fuel system status B:OL-Drive B2: Nej

Fuel system status B:OL-Fault: Nej

Fuel system status B:OL-Fault B2: Nej

Fuel supply system bank 2: Close loop (O2S)

MAP føler: 255 kPa

Luft masse måler: 204.80 g/sek

Throttle position sensor (main): 100.0 %

Lambda sonde / O2 sensor 1, bank 1: 0.425 V

Lambda sonde / O2 sensor 2, bank 1: 0.400 V

O2 sensor 2, bank 3: 0.850 V

Lambda sonde / O2 sensor 1, bank 2: 0.850 V

Lambda sonde / O2 sensor 2, bank 2: 0.300 V

Equivalence ratio (lambda) sensor 1, bank 1: 0.034

A/F Føler 1, bank 1: 7.995 V

Equivalence ratio (lambda) sensor 1, bank 2: 0.002

A/F Føler 1, bank 2: 0.015 V

EGR valve, target position: 100.0 %

Fuel level input: 6.3 %

Barometrisk tryk føler: 85 kPa

Throttle valve relative position: 33.3 %

Throttle position sensor (sub): 52.9 %

Accelerator pedal position sensor (main): 31.4 %

Accelerator pedal position sensor (sub): 97.3 %

Type of fuel: Hybrid Reg. Mode

Ethanol: 70.6 %

Fuel rail pressure sensor (Absolute): 655350 kPa

Relative accelerator pedal position sensor: 100.0 %

Intake air temperature sensor 2: -40 °C

Boost pressure sensor 1: 7.81 kPa

Boost pressure sensor 2: 125.47 kPa

Waste gate position sensor: 100.0 %

Power supply voltage: 18.2 V

Køretøjs hastighed : 510 km/h

Motor Hastighed: 29 Omdr.

Target idle speed: 1992 Omdr.

Intake air temperature sensor bank 1: 79 °C

Motor kølevæske temperatur føler: 77 °C

Belastning Motor: 53 %

Throttle position sensor (main): 4648 mV

Throttle position sensor (sub): 2500 mV

Throttle position sensor (main) learned value: 1660 mV

Accelerator pedal position sensor (main): 2637 mV

Accelerator pedal position sensor (sub): 4199 mV

Ignition advance angle: 234 °

Injection time: 59.9 ms

Electric power steering: 64.0 A

Kortsigtet brændstofafstemning række 1: 0.0 %

Langsigtet brændstofafstemning, række 1: 2.0 %

Knock retard angle: 89.6 °

Learned knock retard: 100.0 %

Intake camshaft adjustment bank 1 phase position: -- °

Tank luft ventil: 100.0 %

Target ETV value: 79.999 V

Throttle valve actuator: 45.9 %

Learned ISC position (A/C off): -119.605 L/s

Learned ISC position (A/C on): -126.863 L/s

Calculated load value: -- %

Absolute load value: -- %

Neutral switch: Tænd

Cranking signal: Tænd

A/C-kontakt: Tænd

Idle speed: Tænd

Ignition switch: Tænd

Oil pressure switch: Tænd

Neutral switch (Auto cruise): Sluk

Brake lamp switch: Tænd

Brake vacuum switch: Tænd

A/C compressor relay: Sluk

Fuel pump relay: Sluk

Power supply relay: Sluk

ETV relay: Sluk

Cooling fan low speed relay: Sluk

Udgangs test

Controls

indsprøjtnings dyser

Fuel pump

Evaporative emission (EVAP) system, canister purge valve

Ignition angle 5°BTDC

Cooling fan high speed

Cooling fan low speed

A/C relay

Oil control valve (CVVT)

Waste gate solenoid valve

Fuel pump

Muligheder

Controls

Rediger stel nr.

Adaptive values (total) reset

Konfiguration

Controls

Redigere konfiguration