Car, MITSUBISHI, PHEV (GG), 2019, GG2W, XDHHZLCS, PHEV
HV battery - PHEV - 0
Identification
Identifier: 00 00
ECU origin: 04
Supplier number: 85
ECU ID: 00
Diagnostic version: 00
Hardware version number: 86 00
Software version: 86 00 04
Part number: 8638A037
Software number: 8637A69600
VIN no (original): JMBXDGG2WEZ004275
Class: DG
Model: Pajero / Montero V8/V9
Type: V98W
Model year: 2007
VIN no: JMBLYV98W7J007862
Calibration ID: 9486A0140601
Calibration verification number (CVN): 6D 2B C5 E0
DTC
C1615: Brake control prohibited request
Controls
Clear DTC
Data stream
Radiator fan 2 relay (diag): On
Parking brake switch / signal: On
Radiator fan 1 relay (diag): On
Brake switch: Off
Interlock switch: On
Power switch (ST) signal: Off
Power switch signal: On
Vacuum pump relay 2 (diag): Off
DIAG control terminal connection: On
Main contactor (-) (diag): On
Back up lamp relay (diag): Off
Main contactor (+) (diag): On
A/C power relay (diag): On
Charge contactor (diag): Off
On board charge start signal: Off
Quick charge start signal: Off
Quick charger start-up signal: Off
On board charge connecting flag: Off
Quick charger connecting flag: Off
Shift position P(SUB): Off
Shift position P(MAIN): Off
Radiator fan 2 relay: On
Main contactor (-): On
Radiator fan 1 relay: On
Main contactor (+): On
12V DC/DC converter shutdown: Not shutdown
Charge contactor output: Off
Motor inverter shutdown: Shutdown
IGCT control power supply relay: On
Vacuum pump relay 2: Off
Back lamp relay: Off
Vacuum pump relay 1: Off
A/C relay: Off
Vacuum pump failsafe relay: On
Water pump relay: On
Quick charge permission signal: Off
Control power supply: 3.86 V
VP relay 2 voltage: 0.00 V
B/P stroke sensor: 2.38 V
B/P stroke sensor power supply: 5.00 V
Brake stroke sensor: 0 mm
Brake pressure sensor (Physical): 0.0 MPa
APS1 power supply: 5.00 V
APS2 power supply: 5.00 V
Accelerator pedal position sensor 1: 1.00 V
Accelerator pedal position sensor 2: 0.98 V
VP negative pressure sensor: 5.00 V
Water temperature sensor: 3.08 V
Quick charge contactor (-): Off
Charge mode switch: Off
Quick charge contactor (+): Off
Paddle switch down (-): Off
ECO mode switch: Off
Paddle switch up (+): Off
Lock switch: Off
Water pump relay (diag): Off
Vacuum pump 1 relay (diag): Off
Quick charge contactor (-) (diag): Off
Quick charge contactor (+) (diag): Off
On vehicle inverter flag: On
Generator inverter shutdown: Not shutdown
Signal for AVAS: On
Front motor inverter shutdown: Shutdown
EV system power supply relay: On
Water pump power supply relay: On
Shift position lamp P: On
Shift sensor 2: 5.00 V
VP relay voltage (monitor): 3.90 V
Shift sensor 1: 2.48 V
Shift sensor 2: 2.54 V
Select sensor 1: 2.42 V
Select sensor 2: 2.44 V
Shift sensor 1: 5.00 V
VP negative pressure sensor: 1.26 V
IGCT control power supply: 1.7 V
EV mode: "
EV sub mode1:
Order of mode transfer priority: ò
EV sub mode 2:
EV-CAN status: ú
Accelerator (control value): 0.98 V
Vehicle speed: 0 km/h
Front motor speed: 0 rpm
Parallel run check mode flag: Off
Parallel run check flag (EOL): Off
Brake warning light state: Off
Check run completion flag: Off
Buzzer state: Off
PDTC clear condition flag: Off
Charge contactor weld flag: Off
MCU shutdown permission flag: Off
Idle judgment flag: Off
Power SW(OFF) historical flag: Off
Power SW(ST) historical flag: Off
Quick charge permission flag: Off
Condenser charge timeout flag: Off
Charge permission flag: Off
MCU ready timeout flag: Off
Main contactor (-) weld flag: Off
Condenser discharge timeout flag: Off
Main contactor (+) weld flag: Off
MAX cell voltage protection flag: Off
Quick charge current timeout: Off
On board charge stop history flag: Off
Quick charge connection judgment: Off
Quick charge stop history flag: Off
OBC connection judgment: Off
On board charge permission flag: Off
WP intermittence drive flag: Off
OBC control status flag: Off
Quick charger control status flag: Off
Torque inhibition (battery) flag: Off
Torque inhibition (motor) flag: Off
Cell temperature high flag: Off
FMCU: READY: Off
On board charge stop flag: Off
Quick charge stop flag: Off
WP low temperature intermittent flag: Off
Limp - home change flag: Off
WP cooling condition flag: Off
FMCU IGBT gate: Off
On-Board charger function: NG
FMCU shutdown F/B: Off
Quick charger function: NG
FMCU power supply keep request: Not requested
Motor temperature: Normal
OBC power supply keep request: Not requested
BMU power supply keep request: Not requested
On-Board charger cooling request: Not requested
BBU active flag: Off
B/P stroke sensor installation: NG
BMU: READY: Off
Ready lamp: Turn off
Quick charger presence: Not Equipment
State of charge (control value): 120.0 %
Battery Total voltage: 496 V
Condenser voltage: 494 V
Shift position (control value): 221
Coolant water temperature: 203 °C
WP speed: 800 rpm
OBC connecting signal: 4.54 V
OBC connecting signal:
BPSS 0 point learning off-set: 21.2 mm
Water pump duty: 55.7 %
Radiator fan 1 duty: 14.9 %
Radiator fan 2 duty: 14.9 %
Oil pump solenoid: 0.050 A
Yaw rate: 0 °/sec
Lateral acceleration: 0.0 m/s²
Longitudinal acceleration: 0.2 m/s²
Steering angle: -40 °
Left front wheel speed sensor: 0 km/h
Right front wheel speed sensor: 0 km/h
Left rear wheel speed sensor: 0 km/h
Right rear wheel speed sensor: 0 km/h
Estimated vehicle speed: 1 km/h
Brake control torque difference: 0 N·m
Front axle distribution torque: 0 N·m
Rear axle distribution torque: 0 N·m
Brake pressure: 0.0 MPa
Running mode: 1
Generator speed: 0 rpm
Rear motor speed: 0 rpm
Barometric pressure: 97 kPa
Control power supply: 14.5 V
Absolute load value: 0 %
Fuel/Air equivalence ratio: 1
Throttle valve relative position: 6.7 %
APS(Main) A/D value: 20.0 %
APS(Sub) A/D value: 9.8 %
SOC for display: 94.5 %
Calculated load value: 0.0 %
Engine coolant temperature: 54 °C
Engine speed: 0.00 rpm
Fuel level input: 62.7 %
Speed control system: Speed control off
Stop lamp switch for speed control: Off
Set (-) switch: On
Brake switch for speed control: On
RES (+) switch: Off
Cruise control flag: On
Cancel switch: On
Cruise control "On"/"Off" switch: On
Speed limiter switch: Off
Vehicle speed for speed control: 0 km/h
Coding counter: 195
Coding state: Not completed
Actuators test
Controls
12VDCDC shutdown
Radiator fan relay 1
Radiator fan relay 2
Back lamp relay
Water pump
Water pump power supply relay
Buzzer
Brake warning telltale
Radiator fan 1 actuate (0%)
Radiator fan 1 actuate (50%)
Radiator fan 1 actuate (100%)
Radiator fan 2 actuate (0%)
Radiator fan 2 actuate (50%)
Radiator fan 2 actuate (100%)
Utility
Controls
Parallel run check mode
Water pump actuate
Vacuum pump actuate
Engine compression measurement
Steering wheel angle offset value reset
B/P stroke sensor learning reset
Configuration
Controls
Edit configuration
Edit option configuration