Car, MITSUBISHI, LANCER (CY, Z0), 2013, CZ4A, SNDFZL, AYC, ACD ACD+ABS(WSS)

Immobilizer - AYC/ACD ACD+ABS(WSS) - 0

Identification

Identifier: 00 02

ECU origin: 04

Supplier number: 85

ECU ID: 00

Diagnostic version: 02

Hardware version number: 00 00

Software version: F1 07 6A

Part number: 631A040

Software number: 8631A040-B

VIN no (original): JMBSNCZ4ACU000261

Class: NC

Model: Not defined

Type: Not allowed

Model year: 2012

VIN no: JMBSNCZ4ACU000261

Calibration ID: --

Calibration verification number (CVN): --

DTC

C2205: SAS internal error

Controls

Clear DTC

Data stream

AWC control mode: Default

Transmission gear position hold request: Off

System fail: Normal

ACD target torque (for meter): No transmit

Steering wheel angle sensor: 0.5 °

Steering angle speed: 0.0 °/sec

Steering wheel angle sensor: Normal

Accelerator pedal position sensor: 0.0 %

Engine speed: 0 rpm

Engine torque (Driver request): -500.0 N·m

Gear position: N

Left front wheel speed sensor: 0.0 km/h

Right front wheel speed sensor: 0.0 km/h

Left rear wheel speed sensor: 0.0 km/h

Right rear wheel speed sensor: 0.0 km/h

Left front wheel speed (raw value): 0.0 rpm

Right front wheel speed (raw value): 0.0 rpm

Left rear wheel speed (raw value): 0.0 rpm

Right rear wheel speed (raw value): 0.0 rpm

Longitudinal acceleration sensor fail flag: Off

Acceleration sensor performance: Normal

Yaw rate sensor: 131.072 °/sec

Yaw rate sensor performance: Normal

Yaw rate sensor fail flag: Off

Lateral acceleration sensor: -0.035 m/s²

Lateral acceleration sensor fail flag: Off

Longitudinal acceleration sensor: 25.690 m/s²

Brake switch (CAN input): Off

Parking brake switch (CAN input): Off

Backup lamp switch: Off

Ignition switch (input): Lock

Battery voltage (CAN input): 0.0 V

IOD fuse (input): On

Odometer (input): 0.0 km

Coding status: Not completed

T/M type (input): Undefined

Rear diff type (input): Undefined

ETACS coding status: Not completed

ECU connection (ABS): Not connected

ECU connection (ENGINE): Not connected

ECU connection (T/M): Not connected

ECU connection (SAS): Not connected

ABS fail flag: Off

ABS actuation flag: Off

WSS fail: Off

Sensor cluster check start request flag: Off

Lateral acceleration sensor check result: Normal

Longitudinal acceleration check result: Normal

Yaw rate sensor check result: Normal

Sensor cluster check complete flag: Off

Sensor cluster check executing flag: Off

Pressure sensor: 0.000 MPa

IG1: Off

Power supply: 0.00 V

Output load voltage: 0.00 V

Pressure sensor power: 0.00 V

Pressure sensor output: 0.00 V

Mode switch: Off

Mode switch (steering) 1: Off

Mode switch (steering) 2: Off

ACD proportion valve (indicated): 0.0 mA

Motor relay drive indication: Off

Yaw rate sensor (adjusted value): 2.60 °/sec

Steering wheel angle sensor (adjusted value): 4.5 °

Lateral acceleration sensor (adjusted value): -0.50 m/s²

Longitudinal G sensor (adjusted value): 0.00 m/s²

Chassis number writing counter: 0 times

Chassis number (original) lock: Unlock

Mileage counter: 0.0 km

Coding counter: 0 times

Utility

Controls

SAS calibration

Lateral acceleration sensor calibration

Longitudinal acceleration sensor calibration

ACD air bleeding

Oil level check

MOTOR DRIVE

ACD operation check

Control OFF