Bil, MITSUBISHI, LANCER (CY, Z0), 2013, CY4A, STMHL6A, AT, CVT, A-MT, TC-SST

Identificere : 00 03

ECU origin: 04

Supplier number: 91

ECU ID: 00

Diagnose version: 03

Hardware version nummer: 00 03

Softwareversion: F0 20 03

Dele nummer: 8631A078

Software nummer: 8631A0780B

VIN no (original): JMBSTCY4A8U011868

Class: TC

Model: Lancer CY

Type: CY4A

Model year: 2008

Stel nr.: JMBSTCY4A8U011868

Calibration ID: --

Calibration verification number (CVN): --

P1902: A/T malfunction (Engine fail Info.)

Clear DTC

Secondary speed sensor: 1 Omdr.

Primary speed sensor: 32 Omdr.

Secondary pressure sensor: 1.3 V

Primary pressure sensor: 1.2 V

CVT oil temperature: 0.8 V

Power supply voltage: 14.3 V

Engine torque (after correction): 6 N·m

Input torque: 19 N·m

Torque ratio: 1.88

Secondary pressure: 1.23 MPa

Primary pressure: 0.95 MPa

CVT oil temperature: 80.00 °C

Vehicle speed (inference): 0 km/h

Real vehicle speed: 0 km/h

Primary speed: 64 Omdr.

Secondary speed: 128 Omdr.

Motor Hastighed: 672 Omdr.

Torque converter slip: 127 Omdr.

Real variable speed ratio: 2.34

Acceleration sensor: 0.00 g

Accelerator pedal position sensor: 0 %

Real engine torque: 6 N·m

Electric oil pump state signal: -- %

Electric oil pump relay monitor: --

Idling stop active state: --

Target primary speed: 1120 Omdr.

Target variable speed ratio: 0.00

Target step: 8 steps

Real step: -30 steps

Target LU differential pressure: 0.00 MPa

Target line pressure: 0.00 MPa

Target secondary pressure: 0.00 MPa

Electric oil pump air bleeding: Completed

Primary pressure solenoid (monitor): 65.535 A

Secondary pressure solenoid monitor current: 65.535 A

Stepper motor coil A: Tænd

Stepper motor coil B: Tænd

Stepper motor coil C: Tænd

Stepper motor coil D: Tænd

LU/SEL changeover solenoid output: Tænd

LU/SEL changeover solenoid monitor: Tænd

Electric oil pump relay: Tænd

Electric oil pump indication signal: 100 %

Line pressure solenoid target: 65.535 A

Primary pressure solenoid (output): 65.535 A

Secondary pressure solenoid output current: 65.535 A

Line pressure solenoid monitor current: 65.535 A

"P" indicator: Tænd

"Ds/L" indicator: Sluk

"R" indicator: Sluk

Indicator L output: Sluk

"N" indicator: Sluk

"D" indicator: Sluk

"Ds" indicator: Sluk

Gearskifteposition: 1st

Idle speed position switch: Tænd

Brake switch: Sluk

Inhibitor switch: P

"DS" position switch: Sluk

Paddle shift switch up (+): Sluk

Paddle switch down (-): Sluk

Select switch (Up): Sluk

Select switch (Down): Sluk

ABS actuation signal: Sluk

TCL actuation signal: Sluk

ABS actuation signal: Sluk

Shift position: N,P

Shift buzzer

Emission gas mode

Clear CVT oil degradation level

Electric oil pump air bleeding

Permit condition for AS&G

CVT information