Car, MITSUBISHI, LANCER (CY, Z0), 2011, CZ4A, SMPFZL1K, AYC, ACD ACD, AYC
Immobilizer - AYC/ACD ACD/AYC - 0
Identification
Identifier: 00 02
ECU origin: 04
Supplier number: 85
ECU ID: 00
Diagnostic version: 02
Hardware version number: 00 00
Software version: F1 07 6A
Part number: 631A040
Software number: 8631A040-B
VIN no (original): JMBSNCZ4ACU000261
Class: NC
Model: Not defined
Type: Not allowed
Model year: 2012
VIN no: JMBSNCZ4ACU000261
Calibration ID: --
Calibration verification number (CVN): --
DTC
C2205: SAS internal error
Controls
Clear DTC
Data stream
Request yaw moment (for meter): Default
AWC control mode: Default
Transmission gear position hold request: Off
System fail: Normal
ACD target torque (for meter): No transmit
Left front brake control indication: No request
Right front brake control indication: No request
Rear ABS control request status: No request
Left rear brake control indication: No request
Right rear brake control indication: No request
Steering wheel angle sensor: 0.5 °
Steering angle speed: 0.0 °/sec
Steering wheel angle sensor: Normal
Accelerator pedal position sensor: 0.0 %
Engine speed: 0 rpm
Engine torque (Driver request): -500.0 N·m
Gear position: N
Left front wheel speed sensor: 0.0 km/h
Right front wheel speed sensor: 0.0 km/h
Left rear wheel speed sensor: 0.0 km/h
Right rear wheel speed sensor: 0.0 km/h
Left front wheel speed (raw value): 0.0 rpm
Right front wheel speed (raw value): 0.0 rpm
Left rear wheel speed (raw value): 0.0 rpm
Right rear wheel speed (raw value): 0.0 rpm
Longitudinal acceleration sensor: 0.000 m/s²
Longitudinal acceleration sensor (status): --
Yaw rate sensor: 0.000 °/sec
Yaw rate sensor (acceleration): 292.21 °/s²
Yaw rate sensor: Normal
Lateral acceleration sensor: 2.501 m/s²
Lateral acceleration sensor: Normal
Master cylinder pressure sensor: 0.00 MPa
Brake switch (CAN input): Off
Parking brake switch (CAN input): Off
Backup lamp switch: Off
Ignition switch (input): Lock
Battery voltage (CAN input): 0.0 V
IOD fuse (input): On
Odometer (input): 0.0 km
Coding status: Not completed
T/M type (input): Undefined
Rear diff type (input): Undefined
ETACS coding status: Not completed
ECU connection (ABS): Not connected
ECU connection (ENGINE): Not connected
ECU connection (T/M): Not connected
ECU connection (SAS): Not connected
Left front wheel ABS actuation flag: Off
Right front wheel ABS actuation flag: Off
Left rear wheel ABS actuation flag: Off
Right rear wheel ABS actuation flag: Off
ABS fail flag: Off
Left front wheel ASC actuation flag: Off
Right front wheel ASC actuation flag: Off
Left rear wheel ASC actuation flag: Off
Right rear wheel ASC actuation flag: Off
ASC fail flag: Off
ASC switch mode: ASC on
Brake control enable flag: Disable
Yaw rate selftest start request flag: Off
Acceleration sensor selftest start request flag: Off
Acceleration sensor selftest executing flag: Off
Yaw rate selftest executing flag: Off
Sensor cluster initial check: Completed
Flame No reception flag: Off
Sensor cluster low voltage flag: Off
Sensor cluster high voltage flag: Off
Pressure sensor: 0.000 MPa
IG1: Off
Power supply: 0.00 V
Output load voltage: 0.00 V
Pressure sensor power: 0.00 V
Pressure sensor output: 0.00 V
Mode switch: Off
Mode switch (steering) 1: Off
Mode switch (steering) 2: Off
ACD proportion valve (indicated): 0.0 mA
AYC proportion valve (indicated): 0.0 mA
LH direction V drive indication: Off
RH direction V drive indication: Off
Motor relay drive indication: Off
Yaw rate sensor (adjusted value): 2.60 °/sec
Steering wheel angle sensor (adjusted value): 4.5 °
Lateral acceleration sensor (adjusted value): -0.50 m/s²
Longitudinal G sensor (adjusted value): 0.00 m/s²
Chassis number writing counter: 0 times
Chassis number (original) lock: Unlock
Mileage counter: 0.0 km
Coding counter: 0 times
Utility
Controls
SAS calibration
Lateral acceleration sensor calibration
Longitudinal acceleration sensor calibration
ACD air bleeding
AYC air bleeding
Oil level check
MOTOR DRIVE
ACD operation check
AYC operation check (left)
AYC operation check (right)
Control OFF