Bil, MITSUBISHI, LANCER (CY, Z0), 2011, CZ4A, SNDFZR, AYC, ACD ACD+ABS(WSS)

Identificere : 00 02

ECU origin: 04

Supplier number: 85

ECU ID: 00

Diagnose version: 02

Hardware version nummer: 00 00

Softwareversion: F1 07 6A

Dele nummer: 631A040

Software nummer: 8631A040-B

VIN no (original): JMBSNCZ4ACU000261

Class: NC

Model: Ikke defineret

Type: Ikke tilladt

Model year: 2012

Stel nr.: JMBSNCZ4ACU000261

Calibration ID: --

Calibration verification number (CVN): --

C2205: SAS internal error

Clear DTC

AWC control mode: Standard

Transmission gear position hold request: Sluk

System fail: Normal

ACD target torque (for meter): No transmit

Ratvinkelføler: 0.5 °

Steering angle speed: 0.0 °/sec

Ratvinkelføler: Normal

Accelerator pedal position sensor: 0.0 %

Motor Hastighed: 0 Omdr.

Engine torque (Driver request): -500.0 N·m

Gear position: N

Venstre forhjulshastighedsføler: 0.0 km/h

Højre forhjulshastighedsføler: 0.0 km/h

Venstre baghjuls hastighedsføler: 0.0 km/h

Højre baghjulshastighedsføler: 0.0 km/h

Left front wheel speed (raw value): 0.0 Omdr.

Right front wheel speed (raw value): 0.0 Omdr.

Left rear wheel speed (raw value): 0.0 Omdr.

Right rear wheel speed (raw value): 0.0 Omdr.

Longitudinal acceleration sensor fail flag: Sluk

Acceleration sensor performance: Normal

Yaw rate sensor: 131.072 °/sec

Yaw rate sensor performance: Normal

Yaw rate sensor fail flag: Sluk

Lateral acceleration sensor: -0.035 m/s²

Lateral acceleration sensor fail flag: Sluk

Longitudinal acceleration sensor: 25.690 m/s²

Brake switch (CAN input): Sluk

Parking brake switch (CAN input): Sluk

Backup lamp switch: Sluk

Ignition switch (input): Lås

Battery voltage (CAN input): 0.0 V

IOD fuse (input): Tænd

Odometer (input): 0.0 km

Coding status: Not completed

T/M type (input): Udefineret

Rear diff type (input): Udefineret

ETACS coding status: Not completed

ECU connection (ABS): Ikke tilsluttet

ECU connection (ENGINE): Ikke tilsluttet

ECU connection (T/M): Ikke tilsluttet

ECU connection (SAS): Ikke tilsluttet

ABS fail flag: Sluk

ABS actuation flag: Sluk

WSS fail: Sluk

Sensor cluster check start request flag: Sluk

Lateral acceleration sensor check result: Normal

Longitudinal acceleration check result: Normal

Yaw rate sensor check result: Normal

Sensor cluster check complete flag: Sluk

Sensor cluster check executing flag: Sluk

Pressure sensor: 0.000 MPa

IG1: Sluk

Power supply: 0.00 V

Output load voltage: 0.00 V

Pressure sensor power: 0.00 V

Pressure sensor output: 0.00 V

Funktionskontakt: Sluk

Mode switch (steering) 1: Sluk

Mode switch (steering) 2: Sluk

ACD proportion valve (indicated): 0.0 mA

Motor relay drive indication: Sluk

Yaw rate sensor (adjusted value): 2.60 °/sec

Steering wheel angle sensor (adjusted value): 4.5 °

Lateral acceleration sensor (adjusted value): -0.50 m/s²

Longitudinal G sensor (adjusted value): 0.00 m/s²

Chassis number writing counter: 0 times

Chassis number (original) lock: Lås op

Mileage counter: 0.0 km

Coding counter: 0 times

SAS calibration

Lateral acceleration sensor calibration

Longitudinal acceleration sensor calibration

ACD air bleeding

Oil level check

MOTOR DRIVE

ACD operation check

Control OFF