Bil, MITSUBISHI, LANCER (CY, Z0), 2011, CZ4A, SMPFZRDW, AYC, ACD ACD, AYC

Identificere : 00 02

ECU origin: 04

Supplier number: 85

ECU ID: 00

Diagnose version: 02

Hardware version nummer: 00 00

Softwareversion: F1 07 6A

Dele nummer: 631A040

Software nummer: 8631A040-B

VIN no (original): JMBSNCZ4ACU000261

Class: NC

Model: Ikke defineret

Type: Ikke tilladt

Model year: 2012

Stel nr.: JMBSNCZ4ACU000261

Calibration ID: --

Calibration verification number (CVN): --

C2205: SAS internal error

Clear DTC

Request yaw moment (for meter): Standard

AWC control mode: Standard

Transmission gear position hold request: Sluk

System fail: Normal

ACD target torque (for meter): No transmit

Left front brake control indication: No request

Right front brake control indication: No request

Rear ABS control request status: No request

Left rear brake control indication: No request

Right rear brake control indication: No request

Ratvinkelføler: 0.5 °

Steering angle speed: 0.0 °/sec

Ratvinkelføler: Normal

Accelerator pedal position sensor: 0.0 %

Motor Hastighed: 0 Omdr.

Engine torque (Driver request): -500.0 N·m

Gear position: N

Venstre forhjulshastighedsføler: 0.0 km/h

Højre forhjulshastighedsføler: 0.0 km/h

Venstre baghjuls hastighedsføler: 0.0 km/h

Højre baghjulshastighedsføler: 0.0 km/h

Left front wheel speed (raw value): 0.0 Omdr.

Right front wheel speed (raw value): 0.0 Omdr.

Left rear wheel speed (raw value): 0.0 Omdr.

Right rear wheel speed (raw value): 0.0 Omdr.

Longitudinal acceleration sensor: 0.000 m/s²

Longitudinal acceleration sensor (status): --

Yaw rate sensor: 0.000 °/sec

Yaw rate sensor (acceleration): 292.21 °/s²

Yaw rate sensor: Normal

Lateral acceleration sensor: 2.501 m/s²

Lateral acceleration sensor: Normal

Master cylinder pressure sensor: 0.00 MPa

Brake switch (CAN input): Sluk

Parking brake switch (CAN input): Sluk

Backup lamp switch: Sluk

Ignition switch (input): Lås

Battery voltage (CAN input): 0.0 V

IOD fuse (input): Tænd

Odometer (input): 0.0 km

Coding status: Not completed

T/M type (input): Udefineret

Rear diff type (input): Udefineret

ETACS coding status: Not completed

ECU connection (ABS): Ikke tilsluttet

ECU connection (ENGINE): Ikke tilsluttet

ECU connection (T/M): Ikke tilsluttet

ECU connection (SAS): Ikke tilsluttet

Left front wheel ABS actuation flag: Sluk

Right front wheel ABS actuation flag: Sluk

Left rear wheel ABS actuation flag: Sluk

Right rear wheel ABS actuation flag: Sluk

ABS fail flag: Sluk

Left front wheel ASC actuation flag: Sluk

Right front wheel ASC actuation flag: Sluk

Left rear wheel ASC actuation flag: Sluk

Right rear wheel ASC actuation flag: Sluk

ASC fail flag: Sluk

ASC switch mode: ASC on

Brake control enable flag: Deaktiver

Yaw rate selftest start request flag: Sluk

Acceleration sensor selftest start request flag: Sluk

Acceleration sensor selftest executing flag: Sluk

Yaw rate selftest executing flag: Sluk

Sensor cluster initial check: Completed

Flame No reception flag: Sluk

Sensor cluster low voltage flag: Sluk

Sensor cluster high voltage flag: Sluk

Pressure sensor: 0.000 MPa

IG1: Sluk

Power supply: 0.00 V

Output load voltage: 0.00 V

Pressure sensor power: 0.00 V

Pressure sensor output: 0.00 V

Funktionskontakt: Sluk

Mode switch (steering) 1: Sluk

Mode switch (steering) 2: Sluk

ACD proportion valve (indicated): 0.0 mA

AYC proportion valve (indicated): 0.0 mA

LH direction V drive indication: Sluk

RH direction V drive indication: Sluk

Motor relay drive indication: Sluk

Yaw rate sensor (adjusted value): 2.60 °/sec

Steering wheel angle sensor (adjusted value): 4.5 °

Lateral acceleration sensor (adjusted value): -0.50 m/s²

Longitudinal G sensor (adjusted value): 0.00 m/s²

Chassis number writing counter: 0 times

Chassis number (original) lock: Lås op

Mileage counter: 0.0 km

Coding counter: 0 times

SAS calibration

Lateral acceleration sensor calibration

Longitudinal acceleration sensor calibration

ACD air bleeding

AYC air bleeding

Oil level check

MOTOR DRIVE

ACD operation check

AYC operation check (left)

AYC operation check (right)

Control OFF