Bil, MERCEDES, E 238, 238.351 E200 4MATIC Coupe, M254 - MRG2 (ME)
M254 - MRG2 (ME) - 0
Identifikation
Diagnose version: 00 4E 0F
Boot software number: --
Hardwareversion: 0.0.0
Softwareversion: --
Software version 1: --
Software version 2: --
Supplier: --
Hardware vare nummer:
Software part number (customer): --
Software part number (code): --
Software part number (data): --
Serie nummer: 00 00 00 00 00 00 00 00 00 00 00 00
Stel nr.:
Fejlkoder
P010000: Mass or volume air flow (MAF) sensor 1/A - electrical fault
Controls
Clear DTC
Levende Data
Motor Hastighed: 500 Omdr.
Kølemiddeltemperatur: 90 °C
Supply voltage: 0.0 V
Oil level: OK
Air conditioning status: Sluk
Idle speed: Ikke registreret
Idle speed increase: 0 Omdr.
Exhaust camshaft adjustment: 0.0 %
Intake camshaft adjustment: 0.0 %
Udstødningsknastakselposition: 0.0 °
Indsugningsknastakselposition: 0.0 °
Gear engaged: P/N
Purging switchover valve: 0 %
Pressure and temperature sensor upstream of throttle valve: 18.6 °C
Ambient pressure: 993.0 hPa
Pressure sensor downstream of air cleaner bank 1: 0.0 hPa
Charge air pressure sensor: 0.0 hPa
Pressure sensor upstream of throttle valve: 0.0 hPa
Indsugningsmanifoldtryk: 0.0 hPa
O2 sensor 1, bank 1 readiness test: Not operational
O2 sensor 1, bank 1 lambda sensor: 0.00
O2 sensor 2, bank 1 readiness test: Not operational
O2 sensor 1, bank 1 lambda sensor: 0.00
Lambda sonde / O2 sensor 2, bank 2: 0.0 V
Oil pressure and oil temperature sensor temperature: 0.0 °C
Full load: Ikke registreret
Belastning Motor: 0 %
Throttle valve actuator: 0 %
Deceleration air switchover valve: Lukket
Knock control: Ikke aktiveret
Knock sensor noise: Nej
Misfire cylinder 1: 2376
Misfire cylinder 2: 1432
Misfire cylinder 3: 1620
Misfire cylinder 4: 1896
Tank pressure differential: 0 hPa
Tank pressure differential (raw value): 0.0 V
Brændstofniveau: 0 L
Brændstofpumpe: Sluk
Low fuel pressure: 0.00 bar
Fuel quantity control valve: 0.0 °
Electric additional compressor: 0 Omdr.
Boost pressure positioner - duty cycle: 11 %
Cylinder 1 and 2 intake CAMTRONIC actuator: 0
Smooth running of cylinder 1: 0.00 (umdr/sec)²
Smooth running of cylinder 2: 0.00 (umdr/sec)²
Smooth running of cylinder 3: 0.00 (umdr/sec)²
Smooth running of cylinder 4: 0.00 (umdr/sec)²
Self-adaptation in idle speed range: 0.00 %
Soot content of particulate filter: 0.0 g
Driven distance since last successful regeneration: 0.0 km
Circuit 15: Sluk
Circuit 87/1: 0.0 V
Circuit 87/3: 0.0 V
Circuit 87/4: 0.0 V
Coolant temperature (raw): 2.6 V
Counter for tuning detection via rail pressure: 305419896
Counter for tuning detection via boost pressure: 2271560481
Counter for tuning detection via control unit software: 4294967295
Vehicle mileage upon first detection of tuning via control unit software: 0 km
Vehicle mileage upon last detection of tuning via control unit software: 0 km
Vehicle mileage upon first detection of tuning via boost pressure: 0 km
Vehicle mileage upon last detection of tuning via boost pressure: 0 km
Vehicle mileage upon first detection of tuning via rail pressure: 0 km
Vehicle mileage upon last detection of tuning via rail pressure: 0 km
Self-adaptation in part load range: 0.00
Exhaust camshaft correction factor bank 1: 0.00 °
Intake camshaft bank 1 correction factor: 0.00 °
Sensor rotor adaptation is completed: Ja
Sensor rotor adaptation is completed: Nej
Sensor rotor adaptation is active: Ja
Sensor rotor adaptation segment 1: 0.00 °
Sensor rotor adaptation segment 2: 0.00 °
Additive correction value for air mass flow: 0.00 kg/h
Correction value for intake manifold pressure: 0.00 bar
Correction factor for air mass flow: 1.9
Correction value of throttle valve for unmetered air: 237.60 kg/h
Intake camshaft position adaptation: Completed
Exhaust camshaft position adaption: Completed
Throttle valve actuator: Lykkedes
Accelerator pedal position sensor: 0 %
Wastegate control pressure transducer: Not taught in
Electric coolant pump (specified value): 0 %
Electric coolant pump: 0.0 A
Boost pressure positioner - duty cycle: 2.6 V
Regulated oil pressure pump valve: 0 %
Inhibit of engine start by crash event: Nej
Immobilizer
Key or key track 1: Ulåst
Key or key track 2: Ulåst
Key or key track 3: Ulåst
Key or key track 4: Ulåst
Key or key track 5: Ulåst
Key or key track 6: Ulåst
Key or key track 7: Ulåst
Key or key track 8: Ulåst
Drive authorization start enable: Nej
Serial number of drive authorization system: A1 00 00 00 00 00 00 00 00 00 00 B2
Data stream 2
Reading of main odometer: 0.00 km
Current operating time: -- ms
Data status:
CVN calculation finished: Not available
Operating time of control unit: 0.00 min
Motor Hastighed: 500.0 Omdr.
Belastning Motor: 0.00 %
Exhaust camshaft position sensor B1: Nej
Intake camshaft position sensor B1: Nej
Knock sensor noise: Nej
Corrected coolant temperature: -273.1 °C
Lambda sonde / O2 sensor 2, bank 1: 0.00 V
Kølemiddeltemperatur: 90.0 °C
Indsugningslufttemperatur: 18.6 °C
Indsugningsmanifoldtryk: 0.0 hPa
Oil pressure: 0
Charge air temperature sensor 2, bank 1: 0.0 °C
Charge air temperature sensor 2, bank 1: 0
Tank pressure differential: 0.0 hPa
Indsugningslufttemperatur: 208.00 °C
Oil pressure: 0.0 hPa
Charge air temperature sensor 1, bank 1: 0
Batteri spænding: 0.0 mV
Accelerator pedal position sensor 1 supply voltage: 0.0 mV
Pressure sensor downstream of throttle valve signal voltage: 0
Tank pressure differential (raw value): 0.00 V
Accelerator pedal position sensor: 0.0 %
Right purging pressure sensor: 0.00 V
Right purging pressure sensor: 0.0 hPa
Fuel tank level: 0.00 L
Fuel tank temperature sensor: 208.00 °C
O2 sensor 1, bank 1 internal resistance limit value: 0.00 Ohm
ECU internal temperature (raw value): 0.00 V
Control module temperature: 208.00 °C
Outside pressure sensor: 0.00 hPa
Lambda value bank 1: 0.00
O2 sensor 1, bank 1 effective heater voltage: 0.00 V
Brændstoftemperaturføler: 0
Brændstoftemperaturføler: 0.0 °C
Tryk i brændstoffordelerrør: 0.00 MPa
Tryk i brændstoffordelerrør: 0.00 V
Tryk i brændstoffordelerrør: 0.00 MPa
Fuel temperature low pressure: 208.00 °C
Boost pressure (raw value): 0
Ladetrykføler: 0.0 hPa
Pressure sensor downstream of air cleaner bank 1: 0.00 V
Pressure sensor downstream of air cleaner bank 1: 0.0 hPa
Pressure sensor upstream of throttle valve: 0.0 hPa
Pressure sensor downstream of air cleaner bank 1: 0.00 hPa
Pressure sensor downstream of air cleaner bank 2: 0.0 hPa
Lambda sonde / O2 sensor 2, bank 1: 0.00
O2 sensor 2, bank 1 is operational: Nej
Dew point sensor: Nej
Oil temperature sensor: 0
Oil temperature: 0.0 °C
Exhaust gas temperature: 0.0 °C
Low fuel pressure: 0.00 kPa
Oil level in sump: 0.0 mm
Oil temperature in sump: 0.0 °C
NOx storage catalyst bank 1 exhaust temperature in cold start: 0.0 °C
Coolant temperature in cold start: 0.0 °C
Circuit 87/1: 0.0 mV
Circuit 87/3: 0.0 mV
Circuit 87/4: 0.0 mV
Charge air pressure sensor: 0.0 hPa
Kickdown-kontakt: Sluk
Brake lights switch: Sluk
Crash signal over direct line: Nej
Circuit 15: Nej
Neutral gear position (shift): Not neutral
Automatisk gearkasse: Nej
Oil level: OK
Wake up network: Nej
Throttle valve position 1 (raw value): 0.00 V
Throttle valve position 2 (raw value): 0.00 V
Throttle valve position 1: 0.00 V
Throttle valve position 2: 0.00 V
Correction factor for fan run-on time: 0.0 %
Throttle valve learning process abort: Nej
Throttle valve actuator status: Ja
Udstødningsknastakselposition: 0.0 °
Indsugningsknastakselposition: 0.0 °
Throttle valve stop position 1: 0.00 V
Throttle valve stop position 2: 0.00 V
Throttle valve opening angle: 0.0 %
Throttle valve relative position: 0.00 %
Engine speed limit: Nej
Intake camshaft bank 1 adaption status: Completed
Exhaust camshaft bank 1 status adaption: Completed
Intake camshaft bank 1 correction factor: 0.0 °
Exhaust camshaft correction factor bank 1: 0.0 °
Fuel quantity control valve: 0
Engine torque coordination (CAMTRONIC): Nej
Boost pressure control (CAMTRONIC): Nej
Variant coding (CAMTRONIC): Nej
Engine torque (CAMTRONIC): Nej
Operating mode (CAMTRONIC): Nej
Engine control system (CAMTRONIC): Nej
Electric coolant pump (specified value): 0.00 %
Electric coolant pump: 0.00 A
Cylinder 1 and 2 intake CAMTRONIC actuator: 0
Cylinder 3 and 4 intake CAMTRONIC actuator: 0
Cylinder 5 and 6 intake CAMTRONIC actuator: 0
Post-start enrichment: 0.00
Gear range engaged: P/N
Rear axle speed: 0.00 km/h
Front axle speed: 0.0 km/h
Air conditioner: Sluk
Compressor actuation: 0
Fan capacity request by air conditioning: 0
Cooling fan request: 0
Outside air temperature: -273.1 °C
Ambient temperature: 208.00 °C
Tank flap: Åben
12V batteristrøm: 0.0 A
Motordrejningsmoment: 0.0 N·m
Coolant temperature at engine start: -273.1 °C
Deceleration brændstoflukning: Nej
Idle speed: Nej
Idle speed controller: Nej
Full load: Nej
After-run: Nej
Compression time cylinder 1: 0.00 ms
Compression time cylinder 2: 0.00 ms
Compression time cylinder 3: 0.00 ms
Compression time cylinder 4: 0.00 ms
Smooth running of cylinder 1: 0.0
Smooth running of cylinder 2: 0.0
Smooth running of cylinder 3: 0.0
Smooth running of cylinder 4: 0.0
Ignition angle retardation average: 0.0 °
Ignition angle cylinder 1: 0.0 °
Ignition angle cylinder 2: 0.0 °
Ignition angle cylinder 3: 0.0 °
Ignition angle cylinder 4: 0.0 °
Sensor rotor adaptation is completed: Nej
Sensor rotor adaptation is completed: Ja
Sensor rotor adaptation segment 1: 0.0 °
Sensor rotor adaptation segment 2: 0.0 °
Sensor rotor adaptation is completed: Nej
Self-adaptation in idle speed range, bank 1 of cylinders: 0.0 %
Additive mixture correction bank 1 HFM: 0.0 %
Additive mixture correction bank 1 (P-System): 0.0 %
Self-adaptation in lower partial-load range, bank 1 of cylinders: 0.00
Self-adaptation in upper partial-load range, bank 1 of cylinders: 0.00
Self-adaptation in upper partial-load range, bank 1 of cylinders: 0.00
Lambda value bank 1: 0.00
Lambda control factor, mean value, bank 1: 0.00
O2 sensor 1, bank 1 is operational: Nej
Lambda setpoint, bank 1: 0.00
Combustion engine distance traveled: 0.00 km
Electric motor distance traveled: 0.00 km
Exhaust camshaft bank 1 (specified value): 0.0 °
Intake camshaft bank 1 (specified value): 0.0 °
Activated charcoal filter filling level: 0.0
Activated charcoal filter filling level: 0.0
Engine temperature (specified value): 0.0 °C
Knock control: Nej
Delete mileage since last error memory or power failure: 0.00 km
Overheating protection: Nej
Stratified operation: Nej
Shutting off injection of individual cylinders: 0
Electric charge injector cylinder 1: --
Electric charge injector cylinder 2: --
Electric charge injector cylinder 3: --
Electric charge injector cylinder 4: --
Electric charge injector cylinder 1 (specified value): --
Electric charge injector cylinder 2 (specified value): --
Electric charge injector cylinder 3 (specified value): --
Electric charge injector cylinder 4 (specified value): --
Injector 1 voltage: --
Injector 2 voltage: --
Injector 3 voltage: --
Injector 4 voltage: --
Fuel quality: 0.00
NOx storage catalyst bank 1 exhaust temperature: -273.1 °C
Exhaust gas temperature sensor 2, bank 1: -273.1 °C
Additive correction value for air mass flow: 0.0 kg/h
Correction value for intake manifold pressure: 0.0 hPa
Pressure sensor downstream of throttle valve: 0.00 hPa
Knock detection reference level cylinder 1: 0.00 bar
Knock detection reference level cylinder 2: 0.00 bar
Knock detection reference level cylinder 3: 0.00 bar
Knock detection reference level cylinder 4: 0.00 bar
Lambda deviation cylinder 1: 0.00
Lambda deviation cylinder 2: 0.00
Lambda deviation cylinder 3: 0.00
Lambda deviation cylinder 4: 0.00
Engine stopping time: 0
Soot content of particulate filter: 0.0 g
Regeneration of particulate filter: Nej
Driven distance since last successful regeneration: 0 m
Reason for abort particulate filter regeneration: process taking too long: Nej
Reason for abort particulate filter regeneration: outside temperature too low: Nej
Reason for abort particulate filter regeneration: exhaust gas temperature too low: Nej
Enabling of regeneration: Nej
Vehicle mileage upon first detection of tuning via control unit software: 0.00 km
Vehicle mileage upon last detection of tuning via control unit software: 0.00 km
Vehicle mileage upon first detection of tuning via boost pressure: 0.00 km
Vehicle mileage upon first detection of tuning via rail pressure: 0.00 km
Vehicle mileage upon last detection of tuning via boost pressure: 0.00 km
Vehicle mileage upon last detection of tuning via rail pressure: 0.00 km
CVN: 00 00 00 00
General denominator (IUMPR): --
Tændingscyklustæller: --
Electric coolant pump: 0.0 %
Electric coolant pump at CPC: 0.00 %
Brændstofpumpe: Sluk
Engine diagnosis indicator lamp: Sluk
Coolant thermostat heating element: 0.00 %
Throttle valve position: 0.0 %
Injector cylinder 1: --
Injector cylinder 3: --
Injector cylinder 4: --
Injector cylinder 2: --
Lambda control: Sluk
Exhaust camshaft bank 1: 0.0 %
Intake camshaft bank 1: 0.0 %
O2 sensor 1, bank 1 heater: --
Fan power effective on/off ratio: 0.00 %
Fuel quantity control valve total actuation angle: 0.0 °
Fuel rail pressure specified value: 0.00 MPa
Idle speed increase: 0.00 Omdr.
Boost pressure positioner - duty cycle: 0.0 %
Deceleration air switchover valve: Åben
Engine oil pump valve: 0.0 %
Diagnostic module tank leakage (DMTL) pump: Sluk
Diagnostic module tank leakage (DMTL) valve: Sluk
Diagnostic module tank leakage (DMTL) heater: Sluk
Electric coolant pump: 0.00 %
Electric additional compressor: 0.00 Omdr.
Speed threshold: 0.0 Omdr.
Ramp time: 0.0 sek
Excitation current limit: 0.0 A
Partial load operation crankcase ventilation valve: Sluk
Udgangs test
Controls
indsprøjtnings dyser
Coolant thermostat heating element
Quantity control valve
Exhaust camshaft solenoid
Intake camshaft solenoid
Rail pressure reduction
Fuel pump
Throttle valve actuator
Electric coolant pump
Purging switchover valve
Wastegate control pressure transducer
Deceleration air switchover valve
Oil pressure regulation valve
Muligheder
Controls
Resetting of values for sensor rotor adaptation
Reset mixture learning
Enabling of engine start after crash event
Fuel pump activation
Teach-in of positions for camshafts
Teaching process of throttle valve stop
Teach-in of wastegate pressure transducer
Teach-in sensor rotor adaptation at vehicle standstill
Teach-in of fuel injectors
Rediger stel nr.
Konfiguration
Controls
Variant coding