Car, MERCEDES, E 213, 213.289 Mercedes-AMG E 63 S 4MATIC Wagon, M177 - MED1775 (ME)

M177 - MED1775 (ME) - 0

Identification

Diagnostic version: 00 3B 0F

Boot software number: --

Hardware version: 6.46.0

Software version: 6.38.0

Software version 1: --

Software version 2: --

Supplier: Marquardt

Hardware part number: 2045450908

Software part number (customer): --

Software part number (code): --

Software part number (data): --

Serial number: --

VIN no: WDD2050401A907454

VIN stored:

DTC

U14038F: Implausible signal 'Fuel level' was received - signal or message is erratic

Controls

Clear DTC

Data stream

Engine speed: 700 rpm

Coolant temperature: 90.00 °C

Intake air temperature sensor bank 1: 39.75 °C

Intake air temperature sensor bank 2: 33.00 °C

Battery voltage: 14.0 V

Air conditioning status: Off

Engine speed (specified): 0 rpm

Throttle valve actuator, bank 1: 2 °

Throttle valve actuator, bank 2: 3 °

Injection time bank 1: 0.30 ms

Injection time bank 2: 0.47 ms

Duty cycle of purging, bank 1: 44.53 %

Duty cycle of purging, bank 2: 57.03 %

Idle speed: Yes

Intake camshaft bank 1: 30.99 °

Intake camshaft bank 2: 31.99 °

Exhaust camshaft bank 1: -32.99 °

Exhaust camshaft bank 2: -33.99 °

Gear range engaged: P/N

Fuel level: 0 L

Boost pressure sensor "A": 1449.22 hPa

Boost pressure sensor "B": 89.22 hPa

Intake manifold pressure bank 1: 5120 hPa

Intake manifold pressure bank 2: 129 hPa

Pressure sensor downstream of air cleaner bank 1: 724.62 hPa

Pressure sensor downstream of air cleaner bank 2: 724.62 hPa

Ambient pressure: Substitute value hPa

Full load: Yes

O2 sensor 1, bank 1: 1.052

O2 sensor 1, bank 2: 1.073

O2 sensor 1, bank 1 status: On

O2 sensor 1, bank 2 status: On

O2 sensor 1, bank 1 is operational: Yes

O2 sensor 1, bank 2 is operational: Yes

O2 sensor 2, bank 1: 168 V

O2 sensor 2, bank 2: 190 V

O2 sensor 2, bank 1: 0.702

O2 sensor 2, bank 2: 0.584

O2 sensor 2, bank 1 is operational: Yes

O2 sensor 2, bank 2 is operational: Yes

Exhaust temperature 1, bank 1: 72 °C

Exhaust temperature 1, bank 2: -222 °C

Engine load: 537 %

Knock control: Yes

Knock sensor noise: No

Injectors: 1; 2; -; -; -; 6; 7; -

Misfire cylinder 1: 38021

Misfire cylinder 2: 1141

Misfire cylinder 3: 14454

Misfire cylinder 4: 6258

Misfire cylinder 5: 905

Misfire cylinder 6: 51525

Misfire cylinder 7: 71

Misfire cylinder 8: 22919

Fuel temperature sensor 1: 39.75 °C

Fuel temperature sensor 2: 52.50 °C

Fuel rail pressure bank 1: 191.4 bar

Fuel rail pressure bank 2: 12.2 bar

Fuel rail pressure specified value: 7.0 bar

Uniformity of lambda control bank 2: 17.86 bar

Uniformity of lambda control bank 1: 21.84 bar

Self-adaptation in idle speed range, bank 1 of cylinders: -1229.86 %

Self-adaptation in idle speed range, bank 2 of cylinders: 30.89 %

Boost pressure sensor "A": 111.91 V

Boost pressure sensor "B": 5.66 V

Intake manifold pressure bank 1: 0.42 V

Intake manifold pressure bank 2: 9.24 V

Pressure sensor downstream of air cleaner bank 1: 110.74 V

Pressure sensor downstream of air cleaner bank 2: 0.42 V

Smooth running of cylinder 1: -187.11 hPa

Smooth running of cylinder 2: 101.00 hPa

Smooth running of cylinder 3: 153.63 hPa

Smooth running of cylinder 4: 126.22 hPa

Smooth running of cylinder 5: 11.42 hPa

Smooth running of cylinder 6: 217.07 hPa

Smooth running of cylinder 7: 15.17 hPa

Smooth running of cylinder 8: 162.85 hPa

Accelerator pedal position sensor supply voltage: 183.8 V

Accelerator pedal position sensor 1 supply voltage: 12.0 V

Accelerator pedal position sensor 2 supply voltage: 7.8 V

Accelerator pedal position sensor: 0 %

Deceleration fuel cut-off: Yes

Injector cylinder 1: 8110T

Injector cylinder 2: 5380H

Injector cylinder 3: 2103L

Injector cylinder 4: 4305E

Injector cylinder 5: 0623N

Injector cylinder 6: 64082

Injector cylinder 7: 05CEY

Injector cylinder 8: 6A564

Generator ID: 1142

Circuit 61: Yes

Calculated generator torque: 133.4 N·m

Generator electrical fault: No

Generator mechanical fault: No

Fan request from air conditioner: 101 %

Fan running: Active

On/off ratio of fan actuation: 100 %

Engine coolant temperature sensor: 6.91 V

Ambient temperature: 5.25 °C

Coolant temperature at engine start: 39.75 °C

Engine temperature (specified value): 91.12 °C

Inside temperature of control unit: 4.50 °C

Correction factor for fan run-on time: 88 %

Coolant thermostat heating element: 227 %

Self-adaptation in upper partial-load range, bank 1 of cylinders: 0.03 %

Self-adaptation in upper partial-load range, bank 2 of cylinders: 1.16 %

Exhaust camshaft position adaption: Yes

Intake camshaft position adaptation: Yes

Correction factor for installation position of exhaust camshaft bank 1: 588.33 %

Correction factor for installation position of exhaust camshaft bank 2: -678.74 %

Correction factor for installation position of intake camshaft bank 1: 24.39 %

Correction factor for installation position of intake camshaft bank 2: 503.60 %

Additive correction value for air mass flow: 189.30 kg/h

Correction factor for air mass flow: 1.38

Throttle position correction value: 2291.9 kg/h

Correction value for intake manifold pressure: 110.55 hPa

Engine oil pump valve: 52 %

Right bypass air switchover valve: Closed

Left bypass air switchover valve: Closed

Boost pressure positioner - duty cycle: 46 %

Heating shut-off valve: Open

Fuel pump: Off

Immobilizer

Serial number of drive authorization system: A1 00 00 00 00 00 00 00 00 00 00 B2

Drive authorization start enable: No

Key or key track 1: Enabled

Key or key track 2: Disabled

Key or key track 3: Enabled

Key or key track 4: Disabled

Key or key track 5: Enabled

Key or key track 6: Disabled

Key or key track 7: Enabled

Key or key track 8: Disabled

Fault status of ECO start/stop function

Clutch: --

On-board electrical system: --

Brake assist: --

ESP: --

Presence of driver: --

Acceleration pedal: --

Transmission: --

DIRECT SELECT lever: --

Steering: --

Electric parking brake: --

Function 'ECO Start': --

Combustion engine: --

Engine hood: --

Starter: --

Fault status of ECO start/stop function (stored)

Clutch: --

On-board electrical system: --

Brake assist: --

ESP: --

Presence of driver: --

Acceleration pedal: --

Transmission: --

DIRECT SELECT lever: --

Steering: --

Electric parking brake: --

Function 'ECO Start': --

Combustion engine: --

Engine hood: --

Starter: --

Odometer: -- km

Causes of engine stop prevention

Outside temperature: --

Brake vacuum: --

Start/Stop eco-start enable button: --

Engine hood: --

Presence of driver: --

Transmission: --

Air conditioning: --

Air suspension: --

Combustion engine: --

Offroad package: --

On-board electrical system: --

System: --

Acceleration pedal: --

Speed threshold: --

Requirements for automatic engine start

Outside temperature: --

On-board electrical system: --

Brake vacuum: --

Start/Stop eco-start enable button: --

Presence of driver: --

System: --

Air conditioning: --

Air suspension: --

Combustion engine: --

Offroad package: --

Starter: --

Actuators test

Controls

Fuel pump

Throttle valve actuator, bank 2

Throttle valve actuator, bank 1

Heating system shut off valve

Left purging switchover valve

Right purging switchover valve

Injectors

Boost pressure control pressure transducer

Left bypass air switchover valve

Right bypass air switchover valve

Engine oil pump valve

Intake camshaft solenoid bank 1

Intake camshaft solenoid bank 2

Exhaust camshaft solenoid bank 1

Exhaust camshaft solenoid bank 2

Utility

Controls

Correction programming of ignition

Fuel quantity correction

Reset mixture learning

Resetting of values for sensor rotor adaptation

Resetting of all adaptation values

Enabling of engine start after crash event

Reset learned values for diagnosis of CAN bus through engine control unit

Teaching process after replacement of combustion engine

Teach-in of throttle valve end stops of right and left throttle valve actuators

Fuel pump activation

Injectors replacement

Edit VIN

Configuration

Controls

Edit configuration