Bil, MERCEDES, E 211, 211.620 E 280 CDI, 2006-, OM642 - CDI4 (CDI)

OM642 - CDI4 (CDI) - 0

Identifikation

Production date: 10 09 14

Hardware number: 47.08

Software nummer: 38.08

Diagnose version: 67.71

MB number for hardware: 00 54 46 60 40

Supplier: Bosch

Identificere : 43 47

Stel nr.: WDC1641221A646619

Fejlkoder

2513: Inlet port shutoff motor. Positioner signals fault

2095: Intake air temperature (IAT) sensor 2 value is above limit

2094: Intake air temperature (IAT) sensor 1 value is above limit

Controls

Clear DTC

Levende Data

Terminal 50 (input): Nej

Fuel tank level: 38 L

Synchronisation status: Initialized (OK)

Terminal 15: Ja

Koblingspedalkontakt: Not operated

Terminal 50 (output, starter actuation): 0.0

Voltage terminal 87: 14.41 V

Speeder pedal positions føler N1: 0 %

Speeder pedal position N2: 0 %

Lambda value: 3

Kølemiddeltemperatur: 58 °C

Tryk i brændstoffordelerrør: 1340 bar

Fuel rail pressure control valve: -278 %

Brændstoftemperaturføler: 11 °C

Fuel rail pressure control: Pressure regulator valve

Kilometer tæller: 20350 km

Fuel quantity control valve: 16 %

Motor Hastighed: 1003 Omdr.

Motor kølevæske temperatur føler: 23 °C

Injected fuel quantity: 13 mm³/hub

MAP føler: 8756 hPa

Ladetrykføler: -33 hPa

Boost air temperature sensor: 37 °C

Barometrisk tryk føler: 9319 hPa

Luft masse måler: 11 mg/hub

Brændstofpumpe: 291.0

Engine speed (specified): [670..730]

Exhaust back pressure: -4361 hPa

Ash content of particulate filter: 15 g

Load state: 157 %

Catalyst temperature sensor 1, bank 1: -817 °C

Temperature sensor upstream of particulate filter: -754 °C

Distance from last ash content correction: 62820 km

Engine running: Ja

Barometric pressure OK: Ja

Coolant temperature OK: Ja

Diesel Particulate filter (DPF) status: Ja

Catalytic converter temperature within specified range: Ja

Heat-up time OK: Ja

Regeneration enabled (no fault entry in CDI control unit): Ja

Fuel temperature is too high: Nej

Vehicle electrical system voltage is too low: Nej

Fuel tank level is too low: Nej

Exhaust gas temperature is too high: Nej

Coolant temperature is too high: Nej

Coolant temperature is too low: Nej

Diesel Particulate filter (DPF) coolant faults: Nej

Charge pressure regulator bank 1: 86 %

Injector 1 voltage: 1.000000

Injector 2 voltage: 1.000000

Injector 3 voltage: 1.000000

Injector 4 voltage: 1.000000

Injector 5 voltage: 1.000000

Injector 6 voltage: 1.000000

EGR valve: 5 %

Differential pressure sensor: -3 hPa

Distance since last successful regeneration: 615 km

Diesel Particulate filter (DPF) flow resistance: 0 hPa/(m3/h)

Throttle valve actuator: 80 %

O2 sensor heating: 41 %

Exhaust gas volume flow rate: 74 m³/h

Cruise control "Accelerate" switch: Nej

Cruise control "Decelerate" switch: Nej

Cruise control "Off" switch: Nej

Cruise control "Resume" switch: Nej

Cruise control "Speedtronic": Nej

Køretøjets hastighed sensor: 0 km/h

CAN bus OFF: Nej

CDI no longer sends on the CAN bus: Nej

CAN bus OFF: Nej

CDI no longer sends on the CAN bus: Nej

Lambda sonde / O2 sensor 1, bank 1: 300 Ohm

Batteri spænding: 14.4 V

Exhaust gas temperature: 906 °C

Quantity correction values of smooth-running control

Stel nr.: WDC1641221A646619

Injector cylinder 1: AKR3DNG

Injector cylinder 2: BBRYDWH

Injector cylinder 3: A2H3FWG

Injector cylinder 4: CKZ1E1H

Injector cylinder 5: CKIGFSH

Injector cylinder 6: BKZ5GSG

Smooth running of cylinder 1: -177.51

Smooth running of cylinder 2: -264.89

Smooth running of cylinder 3: 303.09

Smooth running of cylinder 4: 215.71

Smooth running of cylinder 5: 128.33

Smooth running of cylinder 6: 46.43

Motor Hastighed: 4643 Omdr.

Injection quantity: 134 mm³/hub

Motor kølevæske temperatur føler: 1938.8 °C

Kilometer tæller: 20350 km

Tryk i brændstoffordelerrør: 1340 bar

Drive authorization

Start enable from EIS [EZS]: Ja

Transport protection of control module CDI is detached: Ja

Control module CDI is personalized: Ja

Control module CDI activated: Ja

Synchronization of engine control module and EIS(ESZ): Nej

Test counter of control module DAS: 0

Serie nummer: 82 89 30 42 01 01 62 03

Start enable: Ja

Start enable from electronic transmission control (ETC): Ja

Zero quantity calibration

Fuel rail pressure control: Pressure regulator valve

Kilometer tæller: 20350 km

Adaptation value of cylinder 1 for calibration point 250 bar: 0 us

Adaptation value of cylinder 2 for calibration point 250 bar: 0 us

Adaptation value of cylinder 3 for calibration point 250 bar: 0 us

Adaptation value of cylinder 4 for calibration point 250 bar: 0 us

Adaptation value of cylinder 5 for calibration point 250 bar: 0 us

Adaptation value of cylinder 6 for calibration point 250 bar: 0 us

Adaptation value of cylinder 1 for calibration point 800 bar: 0 us

Adaptation value of cylinder 2 for calibration point 800 bar: 0 us

Adaptation value of cylinder 3 for calibration point 800 bar: 0 us

Adaptation value of cylinder 4 for calibration point 800 bar: 0 us

Adaptation value of cylinder 5 for calibration point 800 bar: 0 us

Adaptation value of cylinder 6 for calibration point 800 bar: 0 us

Adaptation value of cylinder 1 for calibration point 1200 bar: -8 us

Adaptation value of cylinder 2 for calibration point 1200 bar: -4 us

Adaptation value of cylinder 3 for calibration point 1200 bar: -7 us

Adaptation value of cylinder 4 for calibration point 1200 bar: 0 us

Adaptation value of cylinder 5 for calibration point 1200 bar: -6 us

Adaptation value of cylinder 6 for calibration point 1200 bar: 0 us

Teach-in cycle counter for calibration point 250bar: 0

Teach-in cycle counter for calibration point 800bar: 0

Teach-in cycle counter for calibration point 1200bar: 0

Udgangs test

Controls

Fuel pump

Boost pressure valve

EGR-ventil

Engine/AC electric suction fan

Inlet port shutoff motor

Engine compressions test

Quantity correction values of smooth-running control

Muligheder

Controls

Injectors replacement

Diesel particulate filter regeneration

Diesel particulate filter replacement

FN_Start_Routine_DPF_Regeneration_Manual

FN_Stop_Routine_DPF_Regeneration_Manual

Rediger stel nr.

Reset quantity mean value adaptation data

Konfiguration

Controls

Series 203

Series 209

Series 211

Series 164

Series 251

Series 219

Series 463