Bil, MERCEDES, E 210, 210.248 E 200 Compressor, M111 - SIM4 (ME)
M111 - SIM4 (ME) - 0
Identifikation
Production date: 02 05 28
Hardware number: 02.01
Software nummer: 33.01
Diagnose version: 2.34
MB number for hardware: 11 11 53 35 79
Supplier: Siemens
Diagnose version: 02 22.33 01
Stel nr.: WDB2304671F071262
Fejlkoder
P2002-002 (P0123): Accelerator pedal position sensor 1/A/single - circuit open or short to ground
P2002-008 (P0222): Accelerator pedal position sensor 2/B - circuit open or short to ground
P2006-001 (P0113): Intake air temperature (IAT) sensor 1/A/single - circuit open or short to battery
P2024-001 (P0108): Manifold absolute pressure (MAP) sensor - circuit open or short to battery
Controls
Clear DTC
Levende Data
Motor kølevæske temperatur føler: 80 °C
Batteri spænding: 11.42 V
Motorolietemperaturføler: 72 °C
Safety fuel cut-off: Sluk
Fuel tank level: 112 L
Oil level: 35.28 mm
Oil quality: 3.20
Intake air temperature sensor: 36 °C
Motor Hastighed: 0 Omdr.
Idle speed: Sluk
Tændings vinkel: 18 °
Camshaft adjustment: Sluk
Coolant temperature at engine start: 36 °C
Catalyst heating: Tænd
Air pump switchover valve: Tænd
Post-start enrichment: Tænd
EGR valve: 735 °
Koblingspedalkontakt: betjenes
Air conditioner: Sluk
Barometrisk tryk føler: 2379.77 hPa
Gearvælgerstilling: Not P,N
Luft masse måler: 896.01 kg/h
Indsprøjtnings tid B1: 114.69 ms
Gasspjælds positions føler: 735 °
Canister purge control: Sluk
Tank luft ventil: 44 %
Engine speed (specified): 28672 Omdr.
Clutch pedal start enable switch (only USA): Not operated
O2 sensor 1, bank 1 loop control: -43.01 %
Beregnet katalysatortemperatur række 1: -- °C
Lambda sonde / O2 sensor 1, bank 1: 139.9194 V
Lambda control: Sluk
O2 sensor 1, bank 1 heater: Heating capacity DROPPING
Lambda sonde / O2 sensor 2, bank 1: 179.8963 V
O2 sensor / Lambda sonde 2, bank 1 Varme element: Heating capacity CONTROLLED
MAP føler: 3056 hPa
Engine full load: Tænd
Belastning Motor: 88 %
Knock control (B1): Sluk
Motordrejningsmoment: 895.97 N·m
Inertia fuel cut-off: Sluk
Kickdown-kontakt: Not operated
Knock sensor: 2.18400 V
Knock retard angle cylinder 1: -6.00 °
Knock retard angle cylinder 2: 6.00 °
Knock retard angle cylinder 3: -6.00 °
Knock retard angle cylinder 4: 6.00 °
Misfire cylinder 1: 256
Misfire cylinder 2: 512
Misfire cylinder 3: 768
Misfire cylinder 4: 1024
Self-adaptation enabled: Ja
Self-adaptation in idle speed range: 114.69 ms
Self-adaptation in part range: 43 %
Throttle valve stop learned: Ja
Speeder pedal positions føler N1: 140 V
Speeder pedal position N2: 180 V
Gasspjældpositionsføler 1: 140 V
Gasspjældpositionsføler 2: 180 V
Vehicle speed at front axle: 896 km/h
Vehicle speed at rear axle: 896 km/h
Stop light switch: Sluk
Fan capacity effective: 44 %
Fan capacity request by engine: 44 %
Fan capacity request by air conditioning (working load): 44 %
Fan capacity request by air conditioning (basic load): 44 %
Sensor rotor adaptation is completed: Ja
Sensor rotor adaptation: Ikke aktiv
Fuel tank pressure difference: 35.84 hPa
Electric air pump: Tænd
Immobilizer
Serie nummer: 32 21 60 22 20 41 32 01
Engine control module: initialization: Ja
Engine control module: transport protection detached: Ja
Engine control module: personalized: Ja
Engine control module: activated: Ja
Engine control module: start enabled: Nej
Udgangs test
Controls
Secondary air injection system injection
Electronic throttle control (ETC)
EGR Control
Canister purge valve
Engine/AC electric suction fan
Camshaft
Fuel pump
Canister purge cut-off valve
indsprøjtnings dyser
Air/fuel correction
Secondary air injection system solenoid valve
Air pump
Muligheder
Controls
Octan correction
Fuel quantity correction
Correction programming of specified idle speed in selector lever position P or N
Correction programming of specified idle speed with gear range engaged
CO korrigering
Engine/AC electric suction fan
Desensitizing the smooth running detection
Rediger stel nr.
Learn Immobilizer
Closed throttle position learn
Closed EGR position learn
Crankshaft sensor adaptation
Adaptive values (total) reset
Konfiguration
Controls
Redigere konfiguration