Car, HYUNDAI, General, SANTAFE (CM), 2012, G 3.5 MPI, G 3.5 MPI - Leaded All (ENGINE)

G 3.5 MPI - Leaded All (ENGINE) - 0

Identification

Calibration ID:

Calibration verification number (CVN): FF FF FF FF FF FF FF FF

Software version bootloader:

Supplier ECU software number:

Calibration ID:

DTC

Controls

Clear DTC

Data stream

Battery voltage: 17.365 V

State of charge battery: 99.6 %

Engine speed: 16383.8 rpm

Target idle speed: 2550 rpm

Intake manifold pressure: 2560.0 hPa

Water temperature: 143.2 °C

Intake air temperature: 143.2 °C

Engine oil temperature: 143.2 °C

Vehicle speed: 318.8 km/h

Relative air charge: 1536.0 %

A/C pressure sensor built-in: On

Variable camshaft pack: On

Immobilizer built-in: On

Generator PWM built-in: On

Leaded fuel pack: On

WSS signal from ABS: On

WSS signal from front right wheel speed sensor: On

Vehicle speed from transmission: On

A/C switch: On

Variant coding: A/T

Accelerator pedal position at idle position: On

A/C on condition: On

Cooling fan 2: On

MEC set to 0: On

A/C compressor ON by ECU: On

Ignition switch: On

Cooling fan 1: On

Fuel pump: On

Throttle closed position: On

Power supply relay: On

Throttle position: full load: On

Synchronization successed: On

Fuel cut-off condition: On

Condition start: On

Knock control: On

Knock control adaptation is active: On

Knocking detected: On

Engine running detected: On

Camshaft control: On

Camshaft signal detection status: On

Evaporative emission (EVAP) system, canister purge valve: On

Canister purge phase: On

Condition idle controller active: On

Intake camshaft position actuator, bank 1: On

Engine operating status - idle: On

Exhaust camshaft position actuator, bank 1: On

Engine operating status - engine stop: On

Intake camshaft position actuator, bank 2: On

Engine operating status - part load: On

Exhaust camshaft position actuator, bank 2: On

Engine operating status - full load: On

VIS 1 operation status: On

Brake pedal switch: On

VIS 2 operation status: On

Brake lamp switch: On

TEC learnt: On

Power steering switch built-in: On

Accelerator pedal position sensor: 99.6 %

Accelerator pedal position sensor 1: 319.995 V

Accelerator pedal position sensor 2: 319.995 V

APS 1 normalized: 100.0 %

APS 2 normalized: 100.0 %

Idle CO adjustment: 200.0 %

Barometric pressure sensor: 255 kPa

A/C pressure: 4095.875 kPa

Power steering pressure: 12169.200 kPa

Intake camshaft bank 1 target position: 255.992 °

Intake camshaft bank 1 actual position: 255.992 °

Intake camshaft bank 2 target position: 255.992 °

Intake camshaft bank 2 actual position: 255.992 °

Intake camshaft bank 1 position duty cycle: 100.000 %

Intake camshaft bank 2 position duty cycle: 100.000 %

Distance since check engine telltale on: 65535 km

Exhaust camshaft bank 1 target position: 255.992 °

Exhaust camshaft bank 1 actual position: 255.992 °

Exhaust camshaft bank 2 target position: 255.992 °

Exhaust camshaft bank 2 actual position: 255.992 °

Exhaust camshaft bank 1 position duty cycle: 100.000 %

Exhaust camshaft bank 2 position duty cycle: 100.000 %

Injection time cylinder 1: 500.0 ms

Injection time cylinder 2: 500.0 ms

Injection time cylinder 3: 500.0 ms

Injection time cylinder 4: 500.0 ms

Injection time cylinder 5: 500.0 ms

Injection time cylinder 6: 500.0 ms

Ignition angle cylinder 1: 191.2 °

Gear engaged in AT vehicle: -

Throttle position sensor angle mean: 480.0 °

Throttle position sensor 1: 480.0 °

Throttle position sensor 2: 480.0 °

Throttle position sensor set point: 480.0 °

Throttle position sensor 1: 319.99 V

Throttle position sensor 2: 319.99 V

Normalized TPS 1: 319.99 V

Normalized TPS 2: 319.99 V

Actuators test

Controls

Check engine telltale

Fuel pump relay

A/C compressor relay

Fuel pump control

Immobilizer telltale

Cooling fan high speed

Cooling fan low speed

Main relay

Evaporative emission (EVAP) system, canister purge valve

Intake oil control valve

Exhaust oil control valve

CO-potentiometer Trim(Leaded Only)

ETC Motor

Intake manifold tuning (IMT) system, valve

Intake manifold tuning (IMT) system, valve 2

Intake camshaft position actuator, bank 1

Intake camshaft position actuator, bank 2

Exhaust camshaft position actuator, bank 1

Exhaust camshaft position actuator, bank 2

Injectors

Utility

Controls

Auto detected configuration reset

Edit VIN

PCM Lock(MEC) Setting

Idle CO adjustment