Bil, HONDA, JADE, LEB - Petrol
LEB - Petrol - 0
Identifikation
Stel nr.: JHMFD16708S204671
Filename: 37820RNHR610M1
Dele nummer: 37805-RNH-R530
Identificere : 00 07 01 13 01
Fejlkoder
U0291: EPP-CAN malfunction (PCM - Park pawl actuator driver unit)
Controls
Clear DTC
Levende Data
Motor Hastighed: 0 Omdr.
Gasspjælds positions føler: 18.43 %
Throttle valve relative position: 8.12 °
Motor kølevæske temperatur føler: 87.0 °C
Intake air temperature sensor 2: -40.0 °C
MAP føler: 99 kPa
Barometrisk tryk føler: 99 kPa
Køretøjets hastighed sensor: 0 km/h
Calculated load value: 0 %
Backup voltage: 0.00 V
Tændings vinkel: 0.0 °
Batteri spænding: 12.5 V
Generator: 23 %
Indsprøjtnings tid B1: 0.00 ms
EGR valve: 1.49 V
Kommando for EGR-ventil: 0.0 mm
EGR valve: 0.0 mm
Target idle speed actuator: 0 %
Check motor fejllampe: Tænd
Startspærre: Kørsel
A/C clutch: Sluk
A/C-kontakt: Sluk
Luft masse måler: 0.00 g/sek
Ignition angle exhaust side: -64.0 °
Coolant temperature sensor 2: 27.0 °C
Intake air temperature sensor: -40.0 °C
Rocker arm oil pressure sensor: 0 kPa
Høj opløsning batterispænding: 0.00 V
Manifold absolute pressure - high resolution: 0 kPa
A/F Føler 1, bank 1: 128.00 mA
A/F sensor equivalence ratio: 2.00
Luft-/brændstofforhold: 29.4
Kortsigtet brændstofafstemning række 1: 1.99
Langsigtet brændstofafstemning, række 1: 1.99
Target air/fuel ratio: 0.00
Target equivalence ratio (lambda) sensor 1, bank 1: 2.00
Fuel system status (bank 1): Ingen
Lambda sonde / O2 sensor 2, bank 1: 5.00 V
O2 sensor / Lambda sonde 2, bank 1 Varme element: 655.35 A
A/F Føler 1, bank 1: 128.00 mA
A/F sensor 1, bank 1 equivalence ratio: 2.00
Kortsigtet brændstofafstemning række 1: 1.99
Langsigtet brændstofafstemning, række 1: 1.99
Target air/fuel ratio: 0.00
Target equivalence ratio (lambda) sensor 1, bank 1: 2.00
Fuel system status (bank 1): Ingen
Lambda sonde / O2 sensor 2, bank 1: 5.00 V
O2 sensor / Lambda sonde 2, bank 1 Varme element: 655.35 A
A/F Føler 1, bank 2: 128.00 mA
A/F sensor 1, bank 2 equivalence ratio: 2.00
Kortsigtet brændstofafstemning række 2: 1.99
Langsigtet brændstofafstemning, række 2: 1.99
Target air/fuel ratio bank 2: 0.00
Target equivalence ratio (lambda) sensor 1, bank 2: 2.00
Fuel system status (bank 2): Ingen
Lambda sonde / O2 sensor 2, bank 2: 5.00 V
O2 sensor 2, bank 2 heater: Not available A
O2 sensor 1 heater: Tænd
O2 sensor 2 heater: Tænd
O2 sensor 1, bank 1 heater: Tænd
O2 sensor / Lambda sonde 2, bank 1 Varme element: Tænd
CO korrigering: 4.97 V
Alcohol percentage at learned: 100
Fuel alcohol content learned value: Høj kPa
Subfuel solenoid operation: 255 %
Engine oil dilution influenced rate: 255
Fuel alcohol percentage: 255 %
Fuel alcohol content learned condition: Komplet
Abnormal fuel information: Normal
Fuel alcohol content learned condition: Ikke komplet
Engine cold start condition: Tænd
Subfuel pump relay command: Sluk
Speeder pedal positions føler N1: 5.00 V
Speeder pedal position N2: 5.00 V
Accelerator pedal position sensor: 328 %
Gasspjældpositionsføler 1: 5.00 V
Gasspjældpositionsføler 2: 5.00 V
Electronic throttle control (ETC) throttle position: 327.7 °
Target throttle position: 327.7 °
Target throttle position at idle: 327.7 °
VTEC solenoid valve: Tænd
VTEC oil pressure switch: Tænd
Rocker arm oil control solenoid Bank1: Tænd
VTEC oil pressure switch bank 1: Tænd
Rocker arm oil control solenoid Bank2: Tænd
VTEC oil pressure switch bank 2: Tænd
Return signal VTEC solenoid valve: Tænd
VTEC indicator command: Tænd
Camshaft position: 107.5 °
Rocker arm oil pressure switch: Tænd
Solenoid 2 return signal: Tænd
Rocker arm oil control solenoid 2: Tænd
Solenoid 1 return signal: Tænd
Rocker arm oil control solenoid 1: Tænd
Estimated air pressure (PA): 255 kPa
Indsprøjtnings tid B2: 262.14 ms
Rocker arm oil pressure sensor (B): 65535 kPa
Return signal VTEC (VCM) solenoid valve: Tænd
VTEC (VCM) solenoid valve: Sluk
Rocker arm oil pressure switch B bank 1: Tænd
Intake manifold tuning (IMT) system, valve switch: Åben
Intake manifold tuning (IMT) system, valve command: Åben
Mainshaft speed: Not available Omdr.
Countershaft speed: 255 km/h
Reverse lock solenoid: Tænd
Gear position: Not available
Gear position (current): Not available
Start clutch or torque converter slip ratio: 255 kPa
Tank luft ventil: 100 %
Evaporative emission (EVAP) system, canister vent valve: Tænd
EVAP vent solenoid valve return signal: Tænd
Fuel filler cap: Lukket
Trykføler til brændstoftank: 8.27 kPa
Brændstofniveau: 100 %
Fuel level average: 6554 %
A/C pressure sensor: -0.00 MPa
Fuel pressure on fuel rail (Gauge): 765
Brændstoftrykføler: 66 MPa
Differential pressure, intake manifold: 66 MPa
Brændstoftemperaturføler: 215.0 °C
Trykføler til brændstoftank: 65.5 MPa
Fuel tank temperature sensor: 215.0 °C
Fuel meter control: 100 %
Power supply relay: Tænd
Low fuel telltale: Tænd
Injector mode control condition: Tænd
Fuel rail pressure regulator P2 switch: Tænd
Fuel tank pressure sensor (fine): -0.25 Pa
Vehicle status: Not available
Driving status: Not available
Kommando til A/C-kompressor: Tænd
Idle stop control: Tænd
A/C compressor target speed: 65535 Omdr.
Hastighed for A/C-kompressor: 65535 Omdr.
A/C power consumption: -0.00 kW
IMA output command: -0.00 kW
Ladetilstand: 655 %
IMA output: -0.00 kW
High voltage battery temperature: 215.0 °C
DC/DC converter control: 25.5 V
Driving status: Not available
Torque requested by driver: -0.02 N·m
VSA control torque: -0.02 N·m
Cruise request torque: -0.02 N·m
Torque control request (AT): -0.02 N·m
Request regenerative brake torq: -0.02 N·m
Torque request: -0.02 N·m
Target engine torque: -0.02 N·m
Requested IMA motor torque: -0.02 N·m
IMA motor torque: -0.02 N·m
Auto idle stop does not occur (A/C): Ingen
Auto idle stop does not occur (Brake): Ingen
Auto idle stop does not occur (Idle stop switch): Ingen
Auto idle stop does not occur (Clutch pedal position switch): Exist
Auto idle stop does not occur (NP switch): Exist
Auto idle stop does not occur (PCU): Exist
Ladetrykføler: 5.00 V
Turbocharger boost pressure: 874 kPa
Turbocharger boost pressure upper limit: 874 kPa
Bi-fuel: Ikke defineret
Normal judgment information: Normal
Wake-up signal record: Tænd
Turbocharger boost control solenoid valve: 100 %
Turbocharger wastegate solenoid: 100 %
Turbocharger bypass solenoid: Tænd
Turbocharger bypass solenoid valve return: Tænd
Output duty to HCU (heater control unit): 255 %
Power consumption of HCU (heater control unit): 510 W
Neutral position sensor 1: 4.97 V
Neutral position sensor 2: 4.97 V
Motorolietemperaturføler: 4.98 V
Rocker arm oil pressure sensor A: 65535 kPa
Rocker arm oil control solenoid A return: Tænd
Rocker arm oil control solenoid A: Tænd
Rocker arm oil control solenoid B return: Tænd
Rocker arm oil control solenoid B: Tænd
Rocker arm oil pressure switch A: Tænd
Rocker arm oil pressure switch B: Tænd
Rocker arm oil control solenoid A: Tænd
Rocker arm oil control solenoid A return: Tænd
Rocker arm oil control solenoid B: Tænd
Rocker arm oil control solenoid B return: Tænd
Upper shutter grill initial learning: Completed
Lower shutter grill initial learning: Completed
Rocker arm oil control solenoid A Bank1: Tænd
Rocker arm oil control solenoid B Bank1: Tænd
Rocker arm oil control solenoid A Bank2: Tænd
Rocker arm oil control solenoid A Bank1 return: Tænd
Rocker arm oil control solenoid B Bank1 return: Tænd
Rocker arm oil control solenoid A Bank2 return: Tænd
Rear rocker arm oil pressure switch: Tænd
Front rocker arm oil pressure switch: Tænd
Valve pause system status: 255
TMU brake pressure: 65535 kPa
TMU brake pressure: 4.98 V
TMU oil pressure pump speed: 65535 Omdr.
TMU Hi/Low solenoid signal: Tænd
TMU brake solenoid signal: Tænd
Turbocharger boost pressure sensor bank 2: 5.00 V
Turbocharger boost pressure bank 2: 6554 mmHg
Camshaft position sensor bank 2: 108 °
Mass air flow sensor bank 1: 655.4 g/sek
Mass air flow sensor bank 2: 655.4 g/sek
Intake air temperature sensor bank 2: 5.00 V
Intake air temperature sensor bank 2: 215 °C
Throttle position sensor 1, bank 2: 5.00 V
Throttle position sensor 2, bank 2: 5.00 V
Throttle position sensor bank 2: 65535.0 °
Lambda sonde / O2 sensor 1, bank 1: 5.00 V
Oil temperature sensor: 5.00 V
Oil temperature: 215 °C
Intake air temperature sensor: 5.00 V
Indsugningslufttemperatur: 215 °C
Variable oil pump: Tænd
Check engine telltale status: Sluk
Distance since check engine telltale on: 0 km
Idle speed: Sluk
Fuel cut-off: Sluk
Deceleration brændstoflukning: Sluk
VTC status: Sluk
Service check signal: Åben
Mass air flow sensor - high resolution: 6553.5 mg
Tid siden motor start: 0 sek
Trip distance: 0.0 m
Kilometer tæller: 16777215 km
P/N switch: Parkering/frigear
Power steering pressure switch: Sluk
Starter switch: Tænd
ELD sensor output: 1.019 V
ELD (Electrical load detector): 0.0 A
Secondary air injection system pump relay: Tænd
Target idle speed: 0 Omdr.
Idle learn: Komplet
Køleventilator: 255 %
A/C setting temperature: 5.00 V
A/C temperature sensor: 215 °C
A/C pressure: 65.53 MPa
Starter relay signal: Deaktiver
Estimated electric load level: 0.0 A
Starter cut-off relay: 5.00 V
Knock advance: 3.7 °
Knock retard angle: 127.5 °
Knock sensor: 0.00 V
Knock control (B1): 1.99
Knock control (EGR): 0.00
Catalyst temperature sensor: 6488.0 °C
Catalyst temperature sensor 1, bank 1: 6489.6 °C
Catalyst temperature sensor 1, bank 2: -40.0 °C
Power supply relay: Sluk
Fuel pump relay: Sluk
VTC control valve solenoid: 0 %
Target camshaft position: -20.0 °
Knock sensor: 0.00 V
Fuel pump control: Sluk %
Start-up IAT sensor: -40 °C
Coolant temperature at engine start: -40 °C
Intake air temperature sensor 1 block heater information: Not exist
Fejltænding: 0
Misfire (1 cyl - 8 cyl): Nej; Nej; Nej; Nej; Nej; Nej; Nej; Nej
Multi cylinders misfire count: 0 rad/s
Misfire B cylinder 1: 0
Misfire B cylinder 2: 0
Misfire B cylinder 3: 0
Misfire B cylinder 4: 0
Misfire B cylinder 5: 0
Misfire B cylinder 6: 0
Cycles of misfire B: 0
Misfire cylinder 1: 0
Misfire cylinder 2: 0
Misfire cylinder 3: 0
Misfire cylinder 4: 0
Misfire cylinder 5: 0
Misfire cylinder 6: 0
Cycles of misfire: 0
Cruise main switch: Tænd
Cruise set switch: Tænd
Cruise control "Resume" switch: Tænd
Cruise control "Cancel" switch: Tænd
Clutch pedal switch 2: Åben
Cruise control telltale: Tænd
Fartpilotkontakt: Ikke defineret
Bremsepedalkontakt: Tænd
Brake pedal switch 2: Tænd
Cruise brake switch/idle stop switch: Lukket
Brake fluid pressure sensor A: 3653 kPa
Brake fluid pressure sensor B: 3653 kPa
Battery fan return signal: Tænd
Battery fan command: Tænd
Maximum engine speed: 16384 Omdr.
EGR air flow gap: 6554 %
Oil level: 127.5 mm
Motorolietemperaturføler: 215.0 °C
Oil level monitor condition: Aktiv
Motorolietemperaturføler: 215.0 °C
Speeder pedal positions føler N1: 327.7 %
Speeder pedal position N2: 327.7 %
Throttlle position module VSA request: 100.0 °
Requested throttle valve position by cruise control module: 100.0 °
Electronic throttle control (ETC) motor duty: 99 %
Throttle actuator control module relay: Tænd
Throttle actuator supply: Sluk
Throttle actuator supply, bank 2: Sluk
Sportsprogram: Tænd
DBW stuck ratio: 100.0 %
A/F imbalance measurement value: 512.00
A/F imbalance measurement value bank 1: 512
A/F imbalance measurement value bank 2: 512
Current misfire, cylinder 1: 0
Current misfire, cylinder 2: 0
Current misfire, cylinder 3: 0
Current misfire, cylinder 4: 0
Current misfire, cylinder 5: 0
Current misfire, cylinder 6: 0
Idle stop permit time (A/C): 0 sek
Idle stop release counter: 0 sek
Exhaust camshaft duty cycle: 0.00 %
Exhaust camshaft actual position: 0.0 °
Exhaust camshaft target position: 0.0 °
A/F sensor signal plus: 5.00 V
A/F sensor signal minus: 5.00 V
A/F sensor impedance: 510.0 Ohm
Air/Fuel heater duty: 128 %
O2 sensor 2 output: 5.00 V
O2 sensor 1, bank 1 heater duty cycle: 128 %
O2 sensor 2, bank 1 output: 5.00 V
O2 sensor bank 1 heater: 128 %
O2 sensor 2, bank 2 output: 5.00 V
O2 sensor bank 2 heater: 128 %
A/F sensor supply: 4.97 V
A/F sensor heater duty: 128 %
A/F sensor 1, bank 1 mode: Not available
A/F sensor 1, bank 1 pump cell: 25.5 V
A/F sensor 1, bank 1 VS cell signal: 25.5 V
A/F sensor 1, bank 1 supply: 25.5 V
A/F sensor 1, bank 1 impedance: 510.0 Ohm
A/F sensor 1, bank 2 mode: Not available
A/F sensor 1, bank 2 pump cell: 25.5 V
A/F sensor 1, bank 2 VS cell signal: 25.5 V
A/F sensor 1, bank 2 supply: 25.5 V
A/F sensor 1, bank 2 impedance: 510.0 Ohm
Crankshaft sensor disappearance counter: 255
Crankshaft sensor noise counter: 255
Camshaft position sensor "B" disappearance counter: 255
Camshaft position sensor "B" noise counter: 255
Camshaft position sensor "A" disappearance counter: 255
Camshaft position sensor "A" noise counter: 255
Camshaft position sensor 2 disappearance counter: 255
Camshaft position sensor 2 noise counter: 255
Camshaft position sensor 2 disappearance counter: 255
Camshaft position sensor 2 noise counter: 255
Crankshaft position sensor "A" noise counter: 255
Crankshaft position sensor "B" noise counter: 255
Camshaft position sensor noise counter: 255
Crankshaft sensor disappearance counter for the crank angle 6 deg timing system: 65535
Crankshaft sensor noise counter for the crank angle 6 deg timing system: 65535
TDC pulse disappearance counter for the crank angle 6 deg timing system: 65535
TDC pulse noise counter for the crank angle 6 deg timing system: 65535
Catalyst monitor temperature condition B1: OK
Catalyst monitor temperature condition B2: OK
Catalyst monitor efficiency condition: OK
Catalyst monitor efficiency condition B1: OK
Catalyst monitor efficiency condition B2: OK
Batteristrømføler: -0.01 A
Vehicle battery estimated temperature: 215.0 °C
Battery resistance estimated: 25.5 mOhm
Cylinder 1 crank speed: 120 rad/s
Cylinder 2 crank speed: 120 rad/s
Cylinder 3 crank speed: 120 rad/s
Cylinder 4 crank speed: 120 rad/s
Cylinder 5 crank speed: 120 rad/s
Cylinder 6 crank speed: 120 rad/s
The number of driving cycle as which misfire was detected: 255
LAF (Lean Air Flow) sensor, bank 1: Learning incomplete
LAF (Lean Air Flow) sensor, bank 2: Learning incomplete
Idle stop inhibit (AT/CVT: precondition): Stoppet
Idle stop inhibit (PCU): Stoppet
Idle stop inhibit (DC/DC converter): Stoppet
Idle stop inhibit (Brake system): Stoppet
Idle stop inhibit (Battery management system): Stoppet
Idle stop inhibit (HVAC): Stoppet
Idle stop inhibit (ABS/VSA unit): Stoppet
Idle stop inhibit (EPS unit): Stoppet
Idle stop inhibit (Seat belt unfastened): Stoppet
Idle stop inhibit (Hood open): Stoppet
Idle stop inhibit (Idle stop cancel switch): Stoppet
Idle stop inhibit (barometnc air pressure): Stoppet
Idle stop inhibit (drive mode): Stoppet
Idle stop inhibit (AT/CVT: transition condition): Stoppet
Idle stop inhibit (Inclined state): Stoppet
Idle stop inhibit (Operating condition): Stoppet
Idle stop inhibit (Driving history): Stoppet
Idle stop inhibit (Precondition): Stoppet
Idle stop inhibit (starting assist brake): Stoppet
Idle stop inhibit (Vehicle stop judgment): Stoppet
Idle stop inhibit (Battery charging): Normal
Idle stop inhibit (large battery internal resistance): Stoppet
Idle stop inhibit (Battery deterioration): Stoppet
Battery performance degradation: Abnormal
Battery internal resistance: 25.5 mOhm
Idle stop inhibit (Low battery voltage): Stoppet
Idle stop inhibit (EDLC): Stoppet
Idle stop inhibit (Hood open history): Stoppet
Idle stop inhibit (Low voltage capacitor): Stoppet
Charge and discharge (Ultracapacitor): Ikke defineret
Target charging voltage (Ultracapacitor): 25.5 V
Target discharging voltage (Ultracapacitor): 25.5 V
Drive instruction value (Ultracapacitor): Ikke defineret
DC/DC converter status: Operating
DC/DC converter input error 2: Fejl
DC/DC converter input error 1: Fejl
DC/DC converter output error 2: Fejl
DC/DC converter output error 1: Fejl
DC/DC converter internal error: Fejl
DC/DC converter CST(Converter start trigger) error: Fejl
Target fuel pressure direct injection system: 655 MPa
Brændstoftrykføler: 655 MPa
Relief valve: Åben
Relief valve: Abnormal
Brændstoftrykføler: 4.98 V
Entry of ACGF duty outputs value: 655.35 %
Fuel learning: Not completed
Knocking signal input which was processed: 255.0 V
Trykføler til brændstoftank: -0 kPa
Absolute pressure of ELCM (Evaporative Leak Check System) pressure sensor: -0 kPa
Lid open solenoid: Åben
Heater core temperature: 6553.5 °C
HEV system start-up complete: Sluk
Electric water pump target speed: 65535 Omdr.
Water pump speed: 65535 Omdr.
VTEC control changes to "high V/T": Tænd
System start-up status (hybrid): Ikke defineret
Drive device status (hybrid): Ikke defineret
Target torque (drive motor or generator motor): 1310.7 N·m
Motor control direction mode: Ikke defineret
Intake air temperature sensor: 5.00 V
Intake air temperature sensor: 215 °C
Target torque (idle speed): -0.0 N·m
Idle device torque: -0.0 N·m
Target crank end torque value: -0.0 N·m
Target idle torque correction learning: -0.0 N·m
Idle torque: Indlært
Knock retard angle cylinder 1: 128 °
Knock retard angle cylinder 2: 128 °
Knock retard angle cylinder 3: 128 °
Knock retard angle cylinder 4: 128 °
Fuel injector heater duty: 100 %
Injector heater power: 510 W
CNG control unit battery voltage: 9.3 V
CNG control unit IG1 voltage: 14.9 V
CNG tank shut-off valve: Tænd
CNG tank pressure regulator shut-off valve: Tænd
CNG tank internal combustion pressure sensor: 2.93 V
CNG tank fuel pressure sensor: 126 bar
CNG rail pressure sensor: 1.68 V
CNG rail pressure sensor: 4780 mbar
CNG rail temperature sensor: 1.93 V
CNG rail temperature: 61 °C
Wastegate learning: Not completed
Wastegate freezing: No freeze
Waste gate position sensor: 2.3 V
Waste gate position sensor: 1.625 mm
Waste gate position target: 0.149 mm
Wastegate battery voltage: 8.6 V
Wastegate learned value: 2.390 V
Waste gate duty: 86 %
MAP føler: 306 kPa
Wastegate freezing, bank 2: Freeze
Wastegate learning, bank 2: Completed
Waste gate position sensor, bank 2: 5.00 V
Waste gate position sensor, bank 2: -0.001 mm
Wastegate learned value, bank 2: -0.001 V
Waste gate duty, bank 2: -1 %
Camshaft position sensor "A" disappearance counter, bank 2: 255
Camshaft position sensor "A" noise counter, bank 2: 255
Fuel factor study valve cylinder 1: 1
Fuel factor study valve cylinder 2: 0
Fuel factor study valve cylinder 3: 1
Fuel factor study valve cylinder 4: 1
Fuel factor study valve cylinder 5: 0
Fuel factor study valve cylinder 6: 2
VTC control valve solenoid, bank 2: 44 %
VTC status, bank 2: Tænd
Exhaust camshaft bank 2 duty cycle: 100 %
Exhaust camshaft bank 2 actual position: 14.4 °
Exhaust camshaft control, bank 2: Tænd
Electronic throttle control (ETC) motor duty, bank 2: 46 %
Turbocharger bypass solenoid valve return, bank 2: Sluk
Turbocharger bypass solenoid, bank 2: Sluk
Mass air flow sensor bank 2: 1.69 V
Active control engine mount (ACM) control relay: Tænd
ACM unit supply voltage: 3276.75 V
ACM actuator supply voltage: 3276.75 V
Front ACM actuator current: 655.4 A
Rear ACM actuator current: 655.4 A
RFP(Reactive Force Pedal) forced customize: Ikke defineret
RFP(Reactive Force Pedal) forced command: Parameter high limit kg
RFP(Reactive Force Pedal) forced current: Ikke defineret
Sports mode preset: Ikke defineret
Muligheder
Controls
Crank (CKP) pattern clear
Crank (CKP) pattern learning
ECU Reset
Reset throttle position sensor learn
Idle stop starter counter clear
E-VTC learning
Udgangs test
Controls
Fuel pump OFF
All injectors stop
One injector stop
A/C clutch
EVAP-test
Battery fan
VTEC (VCM) test
VTC test
LEB - Petrol - 1
Identifikation
Identificere : 0597020101
Dele nummer: 37805-PWA-Y520
Fejlkoder
P0108: Manifold absolute pressure (MAP) sensor - circuit high voltage
P0107: Manifold absolute pressure (MAP) sensor - circuit low voltage
P0420: Catalyst system bank 1 - efficiency below threshold
P0125: Engine coolant temperature (ECT) sensor - range/performance
P1399: Misfire detection, unidentified cylinder
Controls
Clear DTC
Levende Data
Cooling fan control by ECM: Ja
Fuel pump relay: Sluk
Check motor fejllampe: Sluk
Tændings vinkel: 9.8 °
Indsprøjtnings tid B1: 18.90 ms
Target idle speed actuator: 0 %
A/T lockup A: Sluk
Power steering switch: Sluk
Service check signal: Åben
Starter switch: Sluk
A/C clutch: Tænd
A/C-kontakt: Tænd
Bremsepedalkontakt: Tænd
A/T D4 switch: Sluk
P/N switch: P, N
ACG control: 12.5 V
Generator L terminal: 0 %
ELD (Electrical load detector): 1.8 A
Batteri spænding: 15.9 V
A/T D3 switch: Sluk
A/T lockup B: 0 %
Langsigtet brændstofafstemning, række 1: 0.79
Kortsigtet brændstofafstemning række 1: 0.31
O2 sensor loop control bank 1: Åben sløjfe
Lambda sonde / O2 sensor 1, bank 1: 2.98 V
Gasspjælds positions føler: 0.2 °
MAP føler: 102 kPa
Intake air temperature sensor: -28.4 °C
Motor kølevæske temperatur føler: 56.0 °C
Køretøjets hastighed sensor: 0 km/h
Motor Hastighed: 0 Omdr.
Udgangs test
Muligheder
Controls
O2 sensor test
ECU Reset