Car, HOLDEN, Trax, 2018, Engine - Engine control module

Engine - Engine control module - 0

Identification

VIN no: W0LGT8EBXA1007787

Subscriber ID: O100057235

Programming date: 8209

Identifier: 00 00

System code: 00

XML configuration compatibility identifier: 1

XML data file part number: 0

XML data file alpha code:

Previous subscriber ID: *10MDZ7

2nd previous subscriber ID: *10MDZ7

Manufacturer enable counter (MEC): 0

ECU diagnostic address: --

Detected component: --

Manufacturer`s traceability number: --

Broadcast code: --

Boot software part number: 0

Software module 1 identifier: 12654173

Software module 2 identifier: 55577673

Software module 3 identifier: 55577209

Software module 4 identifier: 55577673

Software module 5 identifier: 55573530

Software module 6 identifier: 55573530

Software module 7 identifier: 55573530

Software module 8 identifier: 55573530

Software module 9 identifier: --

Software module 10 identifier: --

End model part number: 55577619

Base model part number: 55574337

Software part number alpha code: --

Software module 1 identifier alpha code: AA

Software module 2 identifier alpha code: AA

Software module 3 identifier alpha code: --

Software module 4 identifier alpha code: --

Software module 5 identifier alpha code: --

Software module 6 identifier alpha code: --

Software module 7 identifier alpha code: --

Software module 8 identifier alpha code: --

Software module 9 identifier alpha code: --

Software module 10 identifier alpha code: --

End model part number alpha code: 00

Base model part number alpha code: 00

DTC

Controls

Clear DTC

Data stream

Indicated fuel consumption: -- L

Real fuel consumption: -- L

EVAP monitor complete: --

Engine load: 0.0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim: -100 %

Long term fuel trim: -100 %

MAP sensor: 0 kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0.00 km/h

Ignition timing: -64.0 °

Intake air temperature sensor 1: -40 °C

Intake air temperature sensor: -40 °C

Mass air flow sensor: 0.00 g/sec

Throttle position sensor: 0.0 %

EVAP purge solenoid valve command: 0 %

Remaining fuel in tank: 0.0 %

Warm-ups since DTC cleared: 0 Counts

Distance since DTC cleared: 0 km

Fuel tank pressure sensor: 0.00 in. H2O

Baro: 0.0 kPa

Calculated catalyst temperature: -40.00 °C

EVAP monitor enabled this ignition cycle: --

Ignition 1 signal: 0.00 V

Air/Fuel equivalence ratio command: 0.00

Ambient air temperature: -40 °C

Idle speed adjustment: -- rpm

Idle speed correction: -- rpm

Accelerator pedal position sensor 1: 0.0 %

Accelerator pedal position sensor 2: 0 %

Target throttle position: 0 %

Electronic throttle control (ETC) system forced engine shutdown: No

Reduced engine power: Inactive

Wide open throttle: No

APP sensor 1 and 2: Agree

Electronic throttle control (ETC) motor: Enabled

Throttle position sensors 1 and 2: Agree

Cooling fan relays 2 and 3 command: Off

Cooling fan relay 1 command: Off

A/C request: No

A/C cut-off due to A/C pressure out of range: No

A/C Off for WOT: No

A/C compressor clutch relay command: Off

Brake pedal position sensor fully released learn status: Incomplete

Extended travel brake pedal position signal: Inactive

Brake pedal position circuit signal: Open

Brake pedal position sensor signal: Released

Clutch pedal starter inhibit switch: On

Clutch pedal switch: Released

Reverse position switch: Off

O2 sensor 2, bank 1 heater: Off

O2 sensor 1, bank 1 heater: Off

Engine oil pressure switch: Ok

Change engine oil indicator command: Off

Low engine oil level indicator command: Off

Low engine oil pressure indicator command: Off

Engine oil level switch: Ok

Fuel volatility: Low

Cold start: No

EVAP vent solenoid valve command: Not Venting

P/N switch: In gear

Engine controls ignition relay command: Off

Ignition accessory signal: Off

Fuel enrichment - hot catalyst: No

Fuel enrichment - hot coolant: Inactive

Power enrichment: Inactive

Fuel pump relay command: Off

Fuel control loop status: Open

Deceleration fuel cut-off: Inactive

Fuel trim learn: Disabled

Throttle position performance test: Ok

MAP performance test 2: Ok

MAP performance test 1: Ok

MAF performance test: Ok

A/C high side pressure sensor: 0.00 V

Fuel tank pressure sensor: 0.00 V

Engine oil temperature calculated: -40 °C

Fuel level sensor: 0.00 V

Crankshaft position active counter: 0 Counts

Crankshaft position resync counter: 0 Counts

Coolant temperature at engine start: -40 °C

Fuel trim memory cell: 0

Torque management ignition timing retard: 0.0 °

Knock retard: 0.0 °

Calculated air flow: 0.00 g/sec

Target idle speed: 0 rpm

Total number of misfire: 0 Counts

Misfire historic, cylinder 1: 0 Counts

Misfire historic, cylinder 2: 0 Counts

Misfire historic, cylinder 3: 0 Counts

Misfire historic, cylinder 4: 0 Counts

Current misfire, cylinder 2: 0 Counts

Current misfire, cylinder 1: 0 Counts

Current misfire, cylinder 3: 0 Counts

Current misfire, cylinder 4: 0 Counts

Cycles of misfire data: 0 Counts

Warm-ups without emission malfunctions: 0 Counts

Warm-ups without non-emission malfunctions: 0 Counts

Accelerator pedal position sensors: 0.0 %

Throttle position: 0.0 %

Throttle position sensor 1: 0.0 %

Throttle position sensor 2: 0.0 %

Throttle position sensor 2: 0.00 V

Throttle position sensor 1: 0.00 V

Accelerator pedal position sensor 2: 0.00 V

Accelerator pedal position sensor 1: 0.00 V

Injection time bank 1: 0.00 ms

Total knock retard: 0.0 °

Mass air flow sensor: 0 Hz

Misfire diagnostic engine speed: 0 rpm

Misfire diagnostic engine load: 0.0 %

EVAP service bay test result: No test result

EVAP service bay test abort reason: None

EVAP service bay test status: Waiting for purge enable

Fuel tank rated capacity: 0 L

Accelerator pedal position: 0.0 %

Remaining fuel in tank: 0.00 L

Catalyst monitor test counter: 0 Counts

Turbocharger wastegate solenoid valve control circuit high voltage test status: Malfunction

Turbocharger wastegate solenoid valve control circuit low voltage test status: Malfunction

Turbocharger wastegate solenoid valve control circuit open test status: Malfunction

MIL control circuit high voltage test status: Malfunction

MIL control circuit low voltage test status: Malfunction

MIL control circuit open test status: Malfunction

Fuel pump relay control circuit high voltage test status: Malfunction

Fuel pump relay control circuit low voltage test status: Malfunction

Fuel pump relay control circuit open test status: Malfunction

A/C compressor clutch relay control circuit high voltage test status: Malfunction

A/C compressor clutch relay control circuit low voltage test status: Malfunction

A/C compressor clutch relay control circuit open test status: Malfunction

Throttle position sensor 1 fully close learn: 0.00 V

Throttle position sensor 2 fully close learn: 0.00 V

Engine off time: 00:00:00

Throttle motor PWM control signal: 0 %

Intake camshaft position actuator solenoid valve control circuit high voltage test status: Malfunction

Intake camshaft position actuator solenoid valve control circuit low voltage test status: Malfunction

Intake camshaft position actuator solenoid valve control circuit open test status: Malfunction

Exhaust camshaft position actuator solenoid valve control circuit high voltage test status: Malfunction

Exhaust camshaft position actuator solenoid valve control circuit low voltage test status: Malfunction

Exhaust camshaft position actuator solenoid valve control circuit open test status: Malfunction

Ignition coil 1 control circuit high voltage test status: Malfunction

Ignition coil 1 control circuit low voltage test status: Malfunction

Ignition coil 1 control circuit open test status: Malfunction

Ignition coil 2 control circuit high voltage test status: Malfunction

Ignition coil 2 control circuit low voltage test status: Malfunction

Ignition coil 2 control circuit open test status: Malfunction

Ignition coil 3 control circuit high voltage test status: Malfunction

Ignition coil 3 control circuit low voltage test status: Malfunction

Ignition coil 3 control circuit open test status: Malfunction

Ignition coil 4 control circuit high voltage test status: Malfunction

Ignition coil 4 control circuit low voltage test status: Malfunction

Ignition coil 4 control circuit open test status: Malfunction

Cylinder 1 injector control circuit high voltage test status: Malfunction

Cylinder 1 injector control circuit low voltage test status: Malfunction

Cylinder 1 injector control circuit open test status: Malfunction

Cylinder 2 injector control circuit high voltage test status: Malfunction

Cylinder 2 injector control circuit low voltage test status: Malfunction

Cylinder 2 injector control circuit open test status: Malfunction

Cylinder 3 injector control circuit high voltage test status: Malfunction

Cylinder 3 injector control circuit low voltage test status: Malfunction

Cylinder 3 injector control circuit open test status: Malfunction

Cylinder 4 injector control circuit high voltage test status: Malfunction

Cylinder 4 injector control circuit low voltage test status: Malfunction

Cylinder 4 injector control circuit open test status: Malfunction

EVAP purge solenoid valve control circuit high voltage test status: Malfunction

EVAP purge solenoid valve control circuit low voltage test status: Malfunction

EVAP purge solenoid valve control circuit open test status: Malfunction

EVAP vent solenoid valve control circuit high voltage test status: Malfunction

EVAP vent solenoid valve control circuit low voltage test status: Malfunction

EVAP vent solenoid valve control circuit open test status: Malfunction

Cooling fan relay 1 control circuit high voltage test status: Malfunction

Cooling fan relay 1 control circuit low voltage test status: Malfunction

Cooling fan relay 1 control circuit open test status: Malfunction

Cooling fan relays 2 and 3 control circuit high voltage test status: Malfunction

Cooling fan relays 2 and 3 control circuit low voltage test status: Malfunction

Cooling fan relays 2 and 3 control circuit open test status: Malfunction

Camshaft position sensor: 0 rpm

Crankshaft position sensor: 0 rpm

O2 sensor 1, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit open test status: Malfunction

O2 sensor 2, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit open test status: Malfunction

5V reference voltage circuit 1: 0.00 V

5V reference voltage circuit 2: 0.00 V

O2 sensor 1, bank 1 heater: 0 %

O2 sensor 1, bank 1 heater: 0.0 A

O2 sensor 2, bank 1 heater: 0.0 A

Engine controls ignition relay control circuit high voltage test status: Malfunction

Engine controls ignition relay control circuit low voltage test status: Malfunction

Engine controls ignition relay control circuit open test status: Malfunction

Engine controls ignition relay feedback signal: 0.00 V

Cruise control: Inactive

A/C disengagement 1st history: None

A/C disengagement 2nd history: None

A/C disengagement 3rd history: None

A/C disengagement 4th history: None

A/C disengagement 5th history: None

A/C disengagement 6th history: None

A/C disengagement 7th history: None

A/C disengagement 8th history: None

Turbocharger bypass solenoid valve control circuit high voltage test status: Malfunction

Turbocharger bypass solenoid valve control circuit low voltage test status: Malfunction

Turbocharger bypass solenoid valve command: Inactive

Turbocharger bypass solenoid valve control circuit open test status: Malfunction

A/C high side pressure sensor: 0.00 kPa

EVAP service bay test inhibit reason: None

Engine off evap service bay test abort reason: None

Engine off evap service bay test inhibit reason: None

Engine off evap service bay test result: None

Distance to enable engine off evap service bay test: 0.0 km

Fuel trim system test state: Disabled

Short term fuel trim test average: -100 %

Long term fuel trim test average: -100 %

Long term fuel trim test average without purge: -100 %

Knocking detected, cylinder 2: No

Knocking detected, cylinder 4: No

Knocking detected, cylinder 3: No

Knocking detected, cylinder 1: No

Injector disabled, cylinder 4 - misfire detected: No

Injector disabled, cylinder 3 - misfire detected: No

Injector disabled, cylinder 2 - misfire detected: No

Injector disabled, cylinder 1 - misfire detected: No

Exhaust camshaft position command: 0 %

Intake camshaft position command: 0 %

O2 sensor 2, bank 1 heater: 0 %

Exhaust camshaft position: 0.0 °

Intake camshaft position: 0.0 °

Exhaust camshaft target position: 0.0 °

Intake camshaft position target: 0.0 °

Exhaust camshaft position variance: 0.0 °

Intake camshaft position variance: 0.0 °

Exhaust camshaft position active counter: 0 Counts

Intake camshaft position active counter: 0 Counts

Transmission oil temperature: -40 °C

Output shaft speed sensor: 0.00 rpm

Torque delivered signal: 0.00 N·m

MAP sensor: 0.00 V

Intake air temperature sensor 1 at start: -40 °C

Start-up IAT sensor: -40 °C

Intake air temperature sensor 2: -40 °C

Barometric pressure sensor: 0.00 V

Intake manifold tuning (IMT) system, control valve control circuit high voltage test status: Malfunction

Intake manifold tuning (IMT) system, control valve control circuit low voltage test status: Malfunction

Intake manifold tuning (IMT) system, control valve control circuit command: Off

Intake manifold tuning (IMT) system, control valve control circuit open test status: Malfunction

Intake manifold tuning (IMT) system, control valve feedback signal: 0 %

Intake manifold tuning (IMT) system, control valve learn: Inactive

Intake manifold tuning (IMT) system, control valve position:

Clutch pedal position sensor: 0.00 V

Clutch pedal position sensor learned apply position: 0.00 V

Clutch pedal position learn status: Performed successfully

Clutch pedal position sensor learned release position: 0.00 V

Clutch pedal position sensor: 0 %

MIL requested by DTC: No

Check engine telltale: Off

5V reference voltage circuit 4: Ok

5V reference voltage circuit 3: Ok

5V reference voltage circuit 2: Ok

5V reference voltage circuit 1: Ok

Fuel economy actual: 0.0 L/h

Replicated transmission OSS signal: 0 rpm

Torque request inhibit - minimum torque: No

Torque request inhibit - fuel: No

Torque request inhibit - TAC limit: No

Torque request inhibit - ignition timing: No

Torque request inhibit - ignition timing advance: No

Torque request inhibit - TAC: No

Torque request inhibit - minimum idle: No

5V reference voltage circuit 3: 0.00 V

5V reference voltage circuit 4: 0.00 V

Engine coolant thermostat heater command: 0 %

Engine coolant thermostat heater control circuit high voltage test status: Malfunction

Engine coolant thermostat heater control circuit low voltage test status: Malfunction

Engine coolant thermostat heater control circuit open test status: Malfunction

Radiator coolant temperature sensor: -40 °C

Target engine coolant temperature: -40 °C

Throttle body idle air flow compensation: 0 %

Generator indicator command: Off

Catalyst monitor test result: No decision

Catalyst monitor not at idle test conditions met: No

Catalyst monitor test state: Inactive

Reduced engine power history: None

Intake air temperature sensor 2: -40 °C

Power mode: Off

Ignition 1 signal: Off

Accelerator pedal position sensor 2 - circuit status: Ok

Accelerator pedal position sensor 1 - circuit status: Ok

Brake pedal position sensor: 0.00 V

Brake pedal position sensor learned released position: 0.00 V

Brake pedal position sensor: 0 %

Engine calibration monitoring identifier: Not programmed

Engine calibration monitoring: Not present

Calculated barometric pressure: 0.0 kPa

Intake air temperature sensor 2: 0 Hz

Ambient humidity: 0 %

Intake air humidity sensor: 0 %

O2 sensor 1, bank 1: 0.00 V

O2 sensor 2, bank 1: 0.00 V

Driver requested axle torque: -22534 N·m

Accelerator pedal position sensor 1 learned applied position: 0.0 %

Accelerator pedal position sensor 2 learned applied position: 0.0 %

Boost pressure sensor: 0.00 V

Current gear: In progress

Accelerator pedal position sensor 1 learned released position: 0.00 V

Accelerator pedal position sensor 2 learned released position: 0.00 V

Target booster pressure: 0.00 kPa

Turbocharger wastegate solenoid valve command: 0 %

Turbocharger bypass solenoid valve command: 0 %

Boost pressure sensor: 0.00 kPa

Cruise control, PTO and traction control data

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0.00 km/h

Ignition timing: -64.0 °

Ignition 1 signal: 0.00 V

Target throttle position: 0 %

Extended travel brake pedal position signal: Inactive

Brake pedal position circuit signal: Open

Brake pedal position sensor signal: Released

Clutch pedal switch: Released

Engine oil level switch: Ok

Starter relay command: Off

Torque management ignition timing retard: 0.0 °

Target idle speed: 0 rpm

Throttle position: 0.0 %

Cruise control disengagement 1st history: Brake pedal applied

Cruise control disengagement 2nd history: Brake pedal applied

Cruise control disengagement 3rd history: Brake pedal applied

Cruise control disengagement 4th history: Brake pedal applied

Cruise control disengagement 5th history: Brake pedal applied

Cruise control disengagement 6th history: Brake pedal applied

Cruise control disengagement 7th history: Brake pedal applied

Cruise control disengagement 8th history: Brake pedal applied

Accelerator pedal position: 0.0 %

Cruise control "On"/"Off" switch: Off

Cruise control "Cancel" switch: Inactive

Cruise control "Accelerate" switch: Off

Cruise control: Inactive

Cruise control "Set" switch: Inactive

Torque delivered signal: 0.00 N·m

Traction control: Inactive

Engine drag control status: Inactive

Replicated transmission OSS signal: 0 rpm

Cruise control inhibit reason: Brake pedal applied

Cruise control switch: Undetermined state

Driver requested axle torque: -22534 N·m

Electrical and immobilizer data

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0.00 km/h

Ignition 1 signal: 0.00 V

Brake pedal position circuit signal: Open

Brake pedal position sensor signal: Released

Clutch pedal starter inhibit switch: On

Engine oil pressure switch: Ok

Starter relay command: Off

P/N switch: In gear

Engine controls ignition relay command: Off

Ignition accessory signal: Off

Crank request signal: No

Generator F terminal signal: 0.0 %

Immobilizer fuel enable: No

ECM in immobilizer fail enable mode: No

Immobilizer fuel disable: Inactive

Immobilizer fuel disable until ignition off: No

Accelerator pedal position: 0.0 %

Starter relay control circuit high voltage test status: Malfunction

Starter relay control circuit low voltage test status: Malfunction

Starter relay control circuit open test status: Malfunction

Generator L - terminal command: 0.0 %

Engine controls ignition relay control circuit high voltage test status: Malfunction

Engine controls ignition relay control circuit low voltage test status: Malfunction

Engine controls ignition relay control circuit open test status: Malfunction

Engine controls ignition relay feedback signal: 0.00 V

Generator L-terminal circuit high voltage test status: Malfunction

Generator L-terminal circuit low voltage test status: Malfunction

Generator L - terminal command: Off

Generator L-terminal circuit open test status: Malfunction

ECM response source: Ignition switch start

ECM authentication status: Unknown

ECM challenge status: Invalid

Immobilizer security information programmed: No

Immobilizer system status: Standby

Immobilizer password learn : Inactive

Immobilizer security code accepted: No

Immobilizer security code function: Not present

Immobilizer security code programmed: No

Immobilizer security code lockout: No

Immobilizer password learn scan tool delay: Inactive

Immobilizer auto learn counter: 0

Immobilizer automatic learn timer: 0 sec

Immobilizer environment device 2: Ok

Immobilizer environment device 3: Ok

Immobilizer module identification: Incomplete

Immobilizer environment device 4: Ok

Immobilizer transponder identification: Inactive

Immobilizer ECM identifier: Ok

Immobilizer environment device 1: Ok

Immobilizer transponder key: Ok

Immobilizer module security code programmed: No

Immobilizer transponder key identification: Ok

Immobilizer module environment identification: Inactive

Immobilizer security level: 0

Immobilizer password programmed: No

Immobilizer post-release state: Inactive

Immobilizer post-release passive state: Inactive

Immobilizer pre-release state: Inactive

Immobilizer release state: Inactive

MIL requested by DTC: No

Electric power management inhibit reason: None

Immobilizer valid response received time: 0 ms

Generator indicator command: Off

Power mode: Off

Ignition 1 signal: Off

Immobilizer security code lockout active timer: 0 ms

Immobilizer security code programming counter: 0 Counts

Immobilizer security code reset counter: 0 Counts

VIN programing counter: 0 Counts

Engine oil level warning event data

Distance since last oil level warning: 0 km

Distance since last oil pressure warning: 0 km

Engine overspeed event data

Maximum engine speed when engine overspeed detected: 0.0 rpm

Engine speed when engine overspeed detected: 0.0 rpm

Vehicle speed when engine overspeed detected: 0 km/h

Accelerator pedal position when engine overspeed detected: 0.0 %

Engine oil temperature when engine overspeed detected: -40 °C

Current gear when engine overspeed detected: 1

MAF when engine overspeed detected: 0.00 g/sec

Odometer when engine overspeed detected: 0 km

Engine overspeed counter: 0 Counts

Engine overspeed: Not present

Total engine overspeed time: 0 ms

Engine load: 0.0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim: -100 %

Long term fuel trim: -100 %

MAP sensor: 0 kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0.00 km/h

Ignition timing: -64.0 °

Intake air temperature sensor 1: -40 °C

Mass air flow sensor: 0.00 g/sec

EVAP purge solenoid valve command: 0 %

Remaining fuel in tank: 0.0 %

Warm-ups since DTC cleared: 0 Counts

Distance since DTC cleared: 0 km

Baro: 0.0 kPa

Calculated catalyst temperature: -40.00 °C

Ignition 1 signal: 0.00 V

Air/Fuel equivalence ratio command: 0.00

Ambient air temperature: -40 °C

Target throttle position: 0 %

Extended travel brake pedal position signal: Inactive

Brake pedal position circuit signal: Open

Brake pedal position sensor signal: Released

P/N switch: In gear

Engine controls ignition relay command: Off

Ignition accessory signal: Off

Crank request signal: No

Fuel enrichment - hot catalyst: No

Fuel enrichment - hot coolant: Inactive

Power enrichment: Inactive

Fuel control loop status: Open

Deceleration fuel cut-off: Inactive

Fuel trim learn: Disabled

Throttle position performance test: Ok

MAP performance test 2: Ok

MAP performance test 1: Ok

MAF performance test: Ok

Engine oil temperature calculated: -40 °C

Target idle speed: 0 rpm

Distance since first malfunction: 0 km

Distance since last malfunction: 0 km

Ignition cycles with malfunction since 1st malfunction: 0 Counts

Ignition cycles without malfunction since last malfunction: 0 Counts

Ignition cycles without completed test since 1st malfunction: 0 Counts

Throttle position: 0.0 %

Mass air flow sensor: 0 Hz

Accelerator pedal position: 0.0 %

Remaining fuel in tank: 0.00 L

Engine off time: 00:00:00

5V reference voltage circuit 1: 0.00 V

5V reference voltage circuit 2: 0.00 V

Engine controls ignition relay control circuit high voltage test status: Malfunction

Engine controls ignition relay control circuit low voltage test status: Malfunction

Engine controls ignition relay control circuit open test status: Malfunction

Engine controls ignition relay feedback signal: 0.00 V

Turbocharger bypass solenoid valve control circuit high voltage test status: Malfunction

Turbocharger bypass solenoid valve control circuit low voltage test status: Malfunction

Turbocharger bypass solenoid valve control circuit open test status: Malfunction

Transmission fluid temperature sensor: -40 °C

Output shaft speed sensor: 0.00 rpm

Torque delivered signal: 0.00 N·m

Intake air temperature sensor 1 at start: -40 °C

Intake air temperature sensor 2: -40 °C

Barometric pressure sensor: 0.00 V

Intake manifold tuning (IMT) system, control valve feedback signal: 0 %

5V reference voltage circuit 4: Ok

5V reference voltage circuit 3: Ok

5V reference voltage circuit 2: Ok

5V reference voltage circuit 1: Ok

5V reference voltage circuit 3: 0.00 V

5V reference voltage circuit 4: 0.00 V

Intake air temperature sensor 2: -40 °C

Power mode: Off

Intake air temperature sensor 2: 0 Hz

Ambient humidity: 0 %

Intake air humidity sensor: 0 %

O2 sensor 1, bank 1: 0.00 V

O2 sensor 2, bank 1: 0.00 V

Driver requested axle torque: -22534 N·m

Distance this driving cycle: 0 km

Target booster pressure: 0.00 kPa

Turbocharger wastegate solenoid valve command: 0 %

Turbocharger bypass solenoid valve command: 0 %

Boost pressure sensor: 0.00 kPa

Calibration history

Calibration history buffer: Unlocked

Engine calibration part number history 1: --

Calibration verification number history 1: --

Engine calibration part number history 1 counter: --

Engine calibration part number history 2: --

Calibration verification number history 2: --

Engine calibration part number history 2 counter: --

Engine calibration part number history 3: --

Calibration verification number history 3: --

Engine calibration part number history 3 counter: --

Engine calibration part number history 4: --

Calibration verification number history 4: --

Engine calibration part number history 4 counter: --

Engine calibration part number history 5: --

Calibration verification number history 5: --

Engine calibration part number history 5 counter: --

Engine calibration part number history 6: --

Calibration verification number history 6: --

Engine calibration part number history 6 counter: --

Engine calibration part number history 7: --

Calibration verification number history 7: --

Engine calibration part number history 7 counter: --

Engine calibration part number history 8: --

Calibration verification number history 8: --

Engine calibration part number history 8 counter: --

Engine calibration part number history 9: --

Calibration verification number history 9: --

Engine calibration part number history 9 counter: --

Engine calibration part number history 10: --

Calibration verification number history 10: --

Engine calibration part number history 10 counter: --

VIN no: --

Inspection / Maintenance data

Engine coolant temperature sensor: -40 °C

MAP sensor: 0 kPa

Vehicle speed sensor: 0.00 km/h

Intake air temperature sensor 1: -40 °C

Remaining fuel in tank: 0.0 %

Baro: 0.0 kPa

Misfire monitor enabled this ignition cycle: No

Misfire monitor complete this ignition cycle: No

Fuel system monitor enabled this ignition cycle: No

Fuel system monitor complete this ignition cycle: No

Component monitor enabled this ignition cycle: No

Component monitor complete this ignition cycle: No

Catalyst monitor enabled this ignition cycle: --

O2S/HO2S monitor enabled this ignition cycle: --

EVAP monitor enabled this ignition cycle: --

HO2S heater monitor enabled this ignition cycle: --

Secondary air injection system monitor enabled this ignition cycle: --

EGR/Camshaft position monitor enabled this ignition cycle: --

Catalyst monitor complete this ignition cycle: --

O2S/HO2S monitor complete this ignition cycle: --

EVAP monitor complete this ignition cycle: --

HO2S heater monitor complete this ignition cycle: --

Secondary air injection system monitor complete this ignition cycle: --

EGR/Camshaft position monitor complete this ignition cycle: --

Ignition 1 signal: 0.00 V

Ambient air temperature: -40 °C

Brake pedal position circuit signal: Open

Brake pedal position sensor signal: Released

Clutch pedal switch: Released

Cold start: No

Coolant temperature at engine start: -40 °C

Remaining fuel in tank: 0.00 L

Engine off time: 00:00:00

Intake air temperature sensor 1 at start: -40 °C

MIL requested by DTC: No

Check engine telltale: Off

Inspection / Maintenance system status data

Number of DTC: 0

Check engine telltale request: No

Misfire monitor enabled: No

Misfire monitor complete: Yes

Fuel system monitor enabled: No

Fuel system monitor complete: Yes

Component monitor enabled: No

Component monitor complete: Yes

Catalyst monitor enabled: --

Catalyst monitor enabled: --

O2S/HO2S monitor enabled: --

EVAP monitor enabled: --

HO2S heater monitor enabled: --

Secondary air injection system monitor enabled: --

EGR/Camshaft position monitor enabled: --

Catalyst monitor complete: --

Catalyst monitor complete: --

O2S/HO2S monitor complete: --

EVAP monitor complete: --

HO2S heater monitor complete: --

Secondary air injection system monitor complete: --

EGR/Camshaft position monitor complete: --

Actuators test

Controls

A/C compressor clutch relay

Exhaust camshaft position actuator

Exhaust camshaft position actuator solenoid valve

Intake camshaft position actuator

Intake camshaft position actuator solenoid valve

Compression test

Compression test

Cooling fan relay 1

Cooling fan relay 2

Cooling fan relays 2 and 3

Cooling fan relays 1, 2 and 3

Engine coolant thermostat heater

Engine controls ignition relay

Engine speed

Throttle position

Throttle position

Evaporative emission (EVAP) system, canister purge valve

EVAP purge/seal

Evaporative emission (EVAP) system, canister vent valve

Cylinder power balance

Depressurize fuel system

Fuel injector balance

Fuel pump relay

Fuel pump enable

Fuel control loop status

Generator L terminal

Idle ignition timing

Ignition timing retard

Check engine telltale

Intake manifold tuning (IMT) system, valve control

O2 sensor 1, bank 1 heater

O2 sensor 2, bank 1 heater

EVAP service bay test

Starter relay

Turbocharger bypass solenoid valve

Turbocharger wastegate solenoid valve