PKW, CITROEN, SPACETOURER, EDC17C60

Motor - EDC17C60 - 0

Identifikation

Steuergerät-Hersteller: Bosch

Ausrüstungsnummer: 98 06 46 04 80

Softwareversion: FF FF

Edition calibration: FF FF

Software reference: 92 25 57

Zusatznummer: 98 06 46 04 80

FIN: VF3LRHNYHES119264

Motortyp: HNY

Modell: Unbekannt

Fehlercode

P057F: Battery "A" state of charge performance

Controls

Fehlercode löschen

Ist-Werte

Motordrehzahl: 0 UpM

Fahrgeschwindigkeit: 170.2 km/h

Main brake switch: Freigegeben

Kupplungspedalschalter: --

Geber für Fahrpedal 1: 51.2 mV

Geber für Fahrpedal 2: 49.4 mV

Accelerator pedal point of resistance sensor: Tight spot not crossed

Calculated gear: --

Berichtigte Kühlmitteltemperatur: -- °C

Engine coolant temperature reference: 1 °C

Internal combustion engine status: Nicht erlaubt

Außenlufttemperatur : 250 °C

Geber für Kühlmitteltemperatur: -263.0 °C

Starting authorisation coming from the gearbox ECU: Autorisiert

Geber für Kraftstoffdruck: 2.3 Bar

A/C circuit pressure: 36.0 Bar

Engine management ECU: 0.00 V

Supply voltage 5V N1: Fehler

Supply voltage 5V N2: Fehler

Supply voltage 5V N3: Fehler

Supply voltage 5V N4: Fehler

Öldruck: 0.0 Bar

Geber für Kraftstofftemperatur: 221.8 °C

Relais 1 für Kühlgebläse: Nicht aktiviert

Relais 2 für Kühlgebläse: Aktiviert

Fan assembly: Nicht aktiviert

Steuergerät Temperatur: 0 °C

Condition of neutral sensor: Falsch

Rückwärtsgang-Schalter: Reverse gear not engaged

Fuel rail pressure setting: 274 Bar

Fuel pressure measured in the high pressure rail: 1.7 Bar

Fuel pressure regulator control duty cycle: 107.5 %

Position Drosselklappe: 710.2 %

Air metering valve position setting: 708.2 %

Air flow valve duty cycle: 317.0 %

Kurbelwellendrehzahl: 2000.0 UpM

Secondary brake switch: Freigegeben

Oil pressure reference: 0.0 Bar

Luftdrucksensor: 255 mbar

Geber für Gaspedalstellung: 36.6 %

Ancillaries battery charge: 79.5 %

Sensor Kupplungspedalposition: 204.8 %

Sensor Kupplungspedalposition: --

Low pressure fuel pump control duty cycle: 16.0 %

Cruise control reference speed: 0 UpM

Speed limit reference speed: 0 UpM

Turbo position reference value: 11138.4 %

Measured turbo pressure: 4.4 Bar

Turbocharger compressor intake air: -246.6 °C

Sensor Position Drosselklappe: 2.43 V

Sensor Schaufelstellung Turbolader: 9.21 V

Luftmassenmesser: 256 mg/strk

Turbocharger valve duty cycle: 56 %

First initialisation of the turbo: Nicht fertig

Turbo pressure: 0.1 Bar

Air flow reference: 25.6 mg/strk

Geber für Fahrpedal 1: 56.0 %

Geber für Fahrpedal 2: 0.0 %

Ancillaries battery: 200.5 °C

Motordrehzahl (Nockenwelle): 15999.5 UpM

Controlled air inlet module: No movement

Generatorlast: 0 %

Kühlgebläse-Drehzahl: 0 %

Cruise control status (RVV): Fehler

Drivetrain: Geschlossen

Cruise control status (LVV): AUS

Starter control: Nein

Motordrehmoment: -- N·m

Minimum voltage of the battery during starting: -- V

Getriebe: Parken

Turbo position repeat: 650.2 %

Movement of the piloted air inlet module: Jammed

Luftmassenmesser: -- kg/h

Cylinder 1 injector code: 10 11 12 13

Cylinder 2 injector code: 10 11 12 13

Cylinder 3 injector code: 10 11 12 13

Cylinder 4 injector code: 10 11 12 13

Coolant outlet housing position reference value: 75.6 %

Coolant outlet housing control duty cycle: 200.2 %

Sensor Position AGR-Ventil: 68.5 %

Position of the coolant outlet housing: 0.0 %

Position AGR-Ventil: 715.2 %

EGR valve open cycle ratio: 163.8 %

Distance remaining before filling the urea tank: 50 km

Authorisation of injection of the urea fluid based on the pressure: Nein

Authorisation of injection of the urea fluid based on the temperature: Not authorised

Volume of urea fluid remaining in the urea tank: 0.017 L

Zurückgelegte Strecke seit letzter DPF-Regeneration: 4080.4 km

Urea reservoir heating power: -- %

Estimated rate of dilution of the engine oil: 0.0 %

Diesel Particulate filter (DPF) differential pressure: 16390 mbar

Diesel Particulate filter (DPF) regeneration status: None requested

Estimated carbon content of the engine oil: 0.0 %

Condition of the engine oil anti-dilution protection: Inaktiv

Average distance between the last 10 regenerations: 4080.0 km

Diesel Particulate filter (DPF) soot mass: 0.000 g

Quantity of additive deposited in the filter: 128.0 g

Authorisation of regeneration: Not authorized

Additive tank: -- ml

Wasser im Kraftstoff: Fehlen

Abgastemperatur vor Katalysator, Bank 1: 1366.1 °C

DPF rate of clogging with cinders: 6375.1 %

Diesel Particulate filter (DPF) distance remaining before replacement: 4224 km

Diesel Particulate filter (DPF) distance since last changed: 522560 km

DPF estimate of the thermal ageing: 11362.0 %

Distance since last oil change under arduous driving conditions: 6554.0 km

Next oil change: 0 km

Sensor Position AGR-Ventil: 2.77 V

Status of first learning of EGR valve: Fertig

First initialisation of the air mixer: Fertig

Urea heated pipe heating power: 0.6 %

NOx content downstream of the deNOx catalytic converter: 2048 ppm

Urea fluid pressure: 68.906 Bar

NOx content upstream of the deNOx catalytic converter: -- ppm

DeNOx system: Urea gauge-pump module stopped

Estimate of the thermal ageing of the deNOx catalytic converter: 7.1

DeNOx catalytic converter: 175.2 °C

NOx sensor exhaust gas estimated pressure: 4.3 Bar

Einspritzventil 1 Korrekturwert: 0.065

Einspritzventil 2 Korrekturwert: 1.333

Einspritzventil 3 Korrekturwert: 0.049

Einspritzventil 4 Korrekturwert: 0.017

Short term regeneration capacity: 100 %

Long term regeneration capacity: 100 %

Position Drosselklappe: 173 °C

Reference value for the quantity of urea fluid to be injected: 1024.0 mg/s

EGR lower limit learning: Nicht fertig

EGR upper limit learning: Fertig

NOx sensor heater: Nicht aktiviert

Abgastemperatur vor Katalysator, Bank 2: -- °C

DeNOx system bleed: Warten

Volume of urea fluid measured in the urea reservoir: -- L

DeNOx catalytic converter urea load: 33.0 g

Fuel flow regulator: 49.7 A

Calculated injected flow: 24.4 mg/strk

Last learning of the air mixer lower limit: Nicht fertig

Last learning of the air mixer upper limit: Nicht fertig

Last learning of the turbocharger lower limit: Nicht fertig

Last learning of the turbocharger upper limit: Fertig

Quantity of urea solution injected: 4.0 mg/strk

Fuel tank level minimum: Minimum level not reached

Volume of additive remaining in the reservoir: -- ml

Urea tank temperature: 1 °C

First additive status: Terminated

Richness calculated by oxygen sensor: 1

Vacuum available in the braking circuit: Inadequate braking assistance

Stop authorised by the electromotor sub-assembly ECU: Nein

Stop authorised by the engine subsystem: Nein

Stop authorised by the BSI ECU: Nein

Stop authorised by the transaxle ECU: Nein

Stop authorised by the power steering ECU: Nein

Stopping authorised by the ESP ECU: Nein

Stop authorised by the ECUs for the suspension and wheels: Nein

Request for restarting sent by the electric motor sub-assembly ECU: Nein

Request restart engine ECU: Nein

Request for restarting sent by the BSI ECU: Nein

Request for restarting sent by transaxle ECU: Nein

Request for restarting sent by the power steering ECU: Nein

Request for restarting issued by the ESP ECU: Nein

Request for restarting sent by the ECUs for the suspension and wheels: Nein

Ancillary drive belt replacement required: --

Inhibiting of starting or restarting by the engine management ECU: Not inhibited

Voltage at terminals of the power accumulator: 0.00 V

Power accumulator temperature: 98.4 °C

State of health of battery: 0 %

Driver present: Abwesend

ECO mode: Aktiv

Stop/start: Nicht definiert

Engine start/stop switch: Button released

Istwert Motordrehmoment: -2048.0 N·m

Voltage retaining device: Passiv

Estimate of total resistance of the voltage retaining device: 08 FF

Voltage retaining device: 1364.8 °C

Power accumulator voltage reference value: -- V

Latest cause of engine cut-off: No cut-off

Last cause of no stopping of the engine: 0

Vacuum in the vacuum circuit: 388 mbar

Voltage retaining device ECU restart authorisation: Nein

Request for restarting sent by the voltage retaining device ECU: Nein

Stop authorised by the voltage retaining device ECU: Nein

Stopping authorised by the 12 V network: Nein

Battery discharge authorisation status: --

Convergence of state of health of battery: Nein

Power accumulator thermal limitation: Nein

Central voltage retaining device thermal limitation: Nein

Battery charge: -- V

Starting inhibiting control (information by wire): Nein

Causes of failure of the first engine restart: 0

Causes of failure of the second engine restart: 0

Causes of failure of the third engine restart: 0

Batteriespannung: Nicht definiert

Control unit condition: Not locked

Wegfahrsperre-Zustand: Programmed 3 Times

Engine speed on deactivation of the cruise control (last cause): 8000 UpM

Start/stop information

Ancillaries battery charge: 79.5 %

Sensor Kupplungspedalposition: --

Ancillaries battery: 200.5 °C

Drivetrain: Geschlossen

Vacuum available in the braking circuit: Inadequate braking assistance

Stop authorised by the electromotor sub-assembly ECU: Nein

Stop authorised by the engine subsystem: Nein

Stop authorised by the BSI ECU: Nein

Stop authorised by the transaxle ECU: Nein

Stop authorised by the power steering ECU: Nein

Stopping authorised by the ESP ECU: Nein

Stop authorised by the ECUs for the suspension and wheels: Nein

Request for restarting sent by the electric motor sub-assembly ECU: Nein

Request restart engine ECU: Nein

Request for restarting sent by the BSI ECU: Nein

Request for restarting sent by transaxle ECU: Nein

Request for restarting sent by the power steering ECU: Nein

Request for restarting issued by the ESP ECU: Nein

Request for restarting sent by the ECUs for the suspension and wheels: Nein

Ancillary drive belt replacement required: --

Inhibiting of starting or restarting by the engine management ECU: Not inhibited

Voltage at terminals of the power accumulator: 0.00 V

Power accumulator temperature: 98.4 °C

State of health of battery: 0 %

ECO mode: Aktiv

Stop/start: Nicht definiert

Engine start/stop switch: Button released

Istwert Motordrehmoment: -2048.0 N·m

Voltage retaining device: Passiv

Estimate of total resistance of the voltage retaining device: 08 FF

Voltage retaining device: 1364.8 °C

Power accumulator voltage reference value: -- V

Last cause of no stopping of the engine: 0

Vacuum in the vacuum circuit: 388 mbar

Voltage retaining device ECU restart authorisation: Nein

Request for restarting sent by the voltage retaining device ECU: Nein

Stop authorised by the voltage retaining device ECU: Nein

Stopping authorised by the 12 V network: Nein

Battery discharge authorisation status: --

Convergence of state of health of battery: Nein

Power accumulator thermal limitation: Nein

Central voltage retaining device thermal limitation: Nein

Current driving (over the last 20 kilometers)

No vehicle stop authorisation: 0

No power steering stopping authorisation: 0

No chassis stop authorisation: 0

Inadequate braking assistance: 10

No engine stop authorisation: 20

No electromotor subassembly stop authorisation: 30

No restart torque stop authorisation: 40

No gearbox stopping authorisation: 50

Driving between last 20 and 40 kilometers

No vehicle stop authorisation: 255

No power steering stopping authorisation: 135

No chassis stop authorisation: 17

Inadequate braking assistance: 1

No engine stop authorisation: 20

No electromotor subassembly stop authorisation: 24

No restart torque stop authorisation: 19

No gearbox stopping authorisation: 31

Driving between last 40 and 60 kilometers

No vehicle stop authorisation: 255

No power steering stopping authorisation: 135

No chassis stop authorisation: 17

Inadequate braking assistance: 21

No engine stop authorisation: 20

No electromotor subassembly stop authorisation: 24

No restart torque stop authorisation: 19

No gearbox stopping authorisation: 10

DPF information

Zurückgelegte Strecke seit letzter DPF-Regeneration: 4080.4 km

Diesel Particulate filter (DPF) differential pressure: 16390 mbar

Diesel Particulate filter (DPF) regeneration status: None requested

Average distance between the last 10 regenerations: 4080.0 km

Diesel Particulate filter (DPF) soot mass: 0.000 g

Quantity of additive deposited in the filter: 128.0 g

Authorisation of regeneration: Not authorized

Abgastemperatur vor Katalysator, Bank 1: 1366.1 °C

DPF rate of clogging with cinders: 6375.1 %

Diesel Particulate filter (DPF) distance remaining before replacement: 4224 km

Diesel Particulate filter (DPF) distance since last changed: 522560 km

DPF estimate of the thermal ageing: 11362.0 %

Distance since last oil change under arduous driving conditions: 6554.0 km

Short term regeneration capacity: 100 %

Long term regeneration capacity: 100 %

NOx sensor heater: Nicht aktiviert

Abgastemperatur vor Katalysator, Bank 2: -- °C

Volume of additive remaining in the reservoir: -- ml

First additive status: Terminated

Richness calculated by oxygen sensor: 1

Zusatzinformation

Cylinder 1 injector code: 10 11 12 13

Cylinder 2 injector code: 10 11 12 13

Cylinder 3 injector code: 10 11 12 13

Cylinder 4 injector code: 10 11 12 13

Wegfahrsperre

Locking of the ECU: --

Wegfahrsperre-Zustand: --

Problem detected when transmitting the unlock code: --

Stellgliedtest

Controls

Ventil für Abgasrückführung

Magnetventil Turboladersteuerung

Low pressure fuel pump

Cylinder combustion quality

Pressure rising and falling test

Engine compressions test

Dienst­programme

Controls

Austausch Einspritzventile

Filling level of urea tank

Befüllung des Additivreservoirs oder beutels

DPF-Regeneration

DeNOx catalytic converter regeneration

DeNOx system fault reinitialisation

Urea injector replacement

Programming air mixer stops

Programming EGR valve stops

Programming turbocharger stops

EGR valve service cleaning