Bil, CITROEN, BERLINGO, CAN, NFU - Bosch ME7.4.5
NFU - Bosch ME7.4.5 - 0
Identifikation
PSA reference: 96 52 55 23 80
ECU manufacturer: Bosch
Additional number: 96 52 55 23 80
Softwareversion: 13 81
Software reference: 67 24 20
Stel nr.: VF77J5FK0BJ576127
Motortype: 5FK
Model: Berlingo B9
Fejlkoder
P0463: Fuel gauge - circuit open
Controls
Clear DTC
Levende Data
Lambda sonde / O2 sensor 1, bank 1: 165 mV
Lambda sonde / O2 sensor 2, bank 1: 770 mV
Injection time cylinder 1: 3.11 ms
O2 sensor 1 heater duty cycle: 88.0 %
O2 sensor 2 heater duty cycle: 88.0 %
Canister electrovalve duty cycle: 16 %
Canister load estimation: 0 %
Injection time cylinder 2: 3.11 ms
Injection time cylinder 3: 3.06 ms
Injection time cylinder 4: 3.06 ms
Optimum ignition angle: 29 °
Maximum ignition angle: 29 °
Minimum ignition angle: -24 °
Ignition angle applied to each cylinder: 6 °
Knock retard angle cylinder 1: 0 °
Knock retard angle cylinder 2: 0 °
Knock retard angle cylinder 3: 0 °
Knock retard angle cylinder 4: 0 °
Cruise control/speed limiter: 255 km/h
Gearbox gear engaged: 0
Motor Hastighed: 734 Omdr.
Køretøjs hastighed : 0 km/h
Speeder pedal positions føler N1: 400 mV
Speeder pedal position N2: 200 mV
Recalculated accelerator position: 0.0 %
Generatorbelastning: 37 %
Refrigerant circuit pressure: 12.0 bar
Batteri spænding: 14.1 V
Accelerator pedal position sensor: 5000 mV
Air temperature: 48 °C
Kølemiddeltemperatur: 98 °C
Cooling fan reference speed: 51 %
Køleventilatorhastighed: 49 %
Reference manifold pressure: 330 mbar
Measured manifold pressure: 330 mbar
Throttle position sensor reference value: 1 °
Gasspjælds positions føler: 2 °
Gasspjældpositionsføler 1: 580.00 mV
Gasspjældpositionsføler 2: 4400.00 mV
Reference filling: 23 %
Calculated filling: 23 %
Luft masse måler: 8.0 kg/h
Engine torque obtained by managing ignition advance (setting): 0 %
Engine torque obtained by managing air flow (setting): 3 %
Engine torque obtained by managing ignition advance (actual): 0 %
Engine torque obtained by managing air flow (actual): 2 %
Estimated resistive torque: 8 %
Torque required by driver: 0 %
O2 sensor 1, bank 1 loop control: Lukket sløjfe
O2 sensor 2, bank 1 loop control: Åben sløjfe
Brake pedal switch 1: Udløst
Brake pedal switch 2: Udløst
Clutch sensor information: Udløst
Accelerator pedal point of resistance sensor: Udløst
Gearbox type: M/T
Engine operation: Tomgang
Status for fartpilotsystem: Prohibited
Speed limiter status: On standby
Power relay: Ja
Cooling fan high speed relay: Nej
Cooling fan low speed relay: Ja
A/C request: Nej
Compressor power relief reference: 0
Camshaft and crankshaft synchronization: Ja
Immobilizer
Locking of the ECU: Ulåst
Statspærrestatus: Matched ECU
Problem detected when transmitting the unlock code: The programming status of the engine immobiliser cannot be read
Udgangs test
Controls
Electronic throttle control (ETC)
Indsprøjtnings dyse 1
Indsprøjtnings dyse 2
Indsprøjtnings dyse 3
Indsprøjtnings dyse 4
Brændstofpumperelæ
Evaporative emission (EVAP) system, canister purge valve
Cooling fan high speed
Cooling fan low speed
Ignition coil cylinder 1+4
Ignition coil cylinder 2+3
Muligheder
Controls
ECU learn reset