Car, CHEVROLET, Equinox, 2017, 1.5L (LYX) - 1.5L (LYX)

VIN no: W0LGT8EBXA1007787

Software module 1 identifier: 12654173

Software module 2 identifier: 55577673

Software module 3 identifier: 55577209

Software module 4 identifier: 55577673

Software module 5 identifier: 55573530

Software module 6 identifier: 55573530

Software module 7 identifier: 55573530

Software module 8 identifier: 55573530

Software module 9 identifier: --

Software module 10 identifier: --

End model part number: 55577619

Base model part number: 55574337

Clear DTC

EVAP monitor complete: --

Engine load: 0.0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim: -100 %

Long term fuel trim: -100 %

Fuel pressure sensor: 0 kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Intake air temperature sensor 1: -40 °C

Intake air temperature sensor: -40 °C

Mass air flow sensor: 0.00 g/sec

Fuel rail pressure sensor: 0.0 MPa

EVAP purge solenoid valve command: 0 %

Remaining fuel in tank: 0.0 %

Warm-ups since DTC cleared: 0 Counts

Fuel tank pressure sensor: 0.00 in. H2O

Baro: 0.0 kPa

Calculated catalyst temperature: -40 °C

EVAP monitor complete this ignition cycle: --

Air/Fuel equivalence ratio command: 0.00

Air/Fuel equivalence ratio command: 0.00 lambda

Ambient air temperature: -40 °C

Idle speed correction: -- rpm

Target throttle position: 0 %

Current fuel type:

Fuel alcohol content: 0 %

Engine oil type: Conventional

Electronic throttle control (ETC) system forced engine shutdown: No

Reduced engine power: Inactive

Wide open throttle: No

APP sensor 1 and 2: Agree

Electronic throttle control (ETC) motor: Enabled

Throttle position sensors 1 and 2: Agree

Cooling fan relay 1 command: Off

A/C request: No

A/C cut-off due to A/C pressure out of range: No

A/C Off for WOT: No

A/C compressor operation: Not allowed

Brake pedal fully released position learned: No

Brake pedal position sensor fully released learn status: Incomplete

Brake pedal position sensor signal: No

Extended travel brake pedal position signal: Released

Brake pedal position circuit signal: Released

Clutch pedal starter inhibit switch: On

Upshift Indicator command: Off

Clutch pedal switch: Released

Reverse position switch: Off

Reverse inhibit solenoid actuator command: Allowed

O2 sensor 2, bank 1 heater: Off

Change engine oil indicator command: Off

Low engine oil pressure indicator command: Off

Engine oil level switch: Ok

Fuel volatility: Low

Cold start: No

EVAP vent solenoid valve command: Not Venting

Engine controls ignition relay command: Off

Fuel enrichment - hot catalyst: No

Fuel enrichment - hot coolant: Inactive

Power enrichment: Inactive

Fuel pump: Off

Fuel control loop status: Open

Deceleration fuel cut-off: Inactive

Fuel trim learn: Disabled

Throttle position performance test: Ok

MAP performance test 2: Ok

MAP performance test 1: Ok

MAF performance test: Ok

Ignition 1 signal: 0.00 V

A/C high side pressure sensor: 0.00 V

Fuel tank pressure sensor: 0.00 V

Engine oil temperature calculated: -40 °C

Fuel level sensor right tank: 0.00 V

Fuel level sensor: 0.00 V

Crankshaft position active counter: 0 Counts

Crankshaft position resync counter: 0 Counts

Coolant temperature at engine start: -40 °C

Fuel trim memory cell: 0

Torque management ignition timing retard: 0.0 °

Knock retard: 0 °

Calculated air flow: 0.00 g/sec

Target idle speed: 0 rpm

Total number of misfire: 0 Counts

Misfire historic, cylinder 1: 0 Counts

Misfire historic, cylinder 2: 0 Counts

Misfire historic, cylinder 3: 0 Counts

Misfire historic, cylinder 4: 0 Counts

Current misfire, cylinder 2: 0 Counts

Current misfire, cylinder 1: 0 Counts

Current misfire, cylinder 3: 0 Counts

Current misfire, cylinder 4: 0 Counts

Cycles of misfire data: 0 Counts

Warm-ups without emission malfunctions: 0 Counts

Warm-ups without non-emission malfunctions: 0 Counts

Distance since DTC cleared: 0 km

EVAP malfunction history: None

Accelerator pedal position sensors: 0 %

Throttle position: 0 %

Accelerator pedal position sensor 1: 0 %

Accelerator pedal position sensor 2: 0 %

Throttle position sensor 1: 0 %

Throttle position sensor 2: 0 %

Throttle position sensor 2: 0.00 V

Throttle position sensor 1: 0.00 V

Accelerator pedal position sensor 2: 0.00 V

Accelerator pedal position sensor 1: 0.00 V

Injection time bank 1: 0.00 ms

Total knock retard: 0 °

Mass air flow sensor: 0 Hz

Misfire diagnostic engine speed: 0 rpm

Misfire diagnostic engine load: 0 %

EVAP service bay test result: No test result

EVAP service bay test abort reason: None

EVAP service bay test status: Waiting for purge enable

Fuel tank rated capacity: 0 L

Accelerator pedal position: 0 %

Remaining fuel in tank: 0 L

Torque delivered signal: 0 N·m

Fuel level sensor left tank: 0.00 V

Catalyst monitor test counter: 0 Counts

Turbocharger wastegate solenoid valve control circuit high voltage test status: Malfunction

Turbocharger wastegate solenoid valve control circuit low voltage test status: Malfunction

Turbocharger wastegate solenoid valve control circuit open test status: Malfunction

MIL control circuit high voltage test status: Malfunction

MIL control circuit low voltage test status: Malfunction

MIL control circuit open test status: Malfunction

Fuel pump relay control circuit high voltage test status: Malfunction

Fuel pump relay control circuit low voltage test status: Malfunction

Fuel pump relay control circuit open test status: Malfunction

A/C compressor clutch relay control circuit high voltage test status: Malfunction

A/C compressor clutch relay control circuit low voltage test status: Malfunction

A/C compressor clutch relay control circuit open test status: Malfunction

Cooling fan motor command: 0 %

Engine off time: 00:00:00

Throttle motor PWM control signal: 0 %

Intake camshaft position actuator solenoid valve control circuit high voltage test status: Malfunction

Intake camshaft position actuator solenoid valve control circuit low voltage test status: Malfunction

Intake camshaft position actuator solenoid valve control circuit open test status: Malfunction

Exhaust camshaft position actuator solenoid valve control circuit high voltage test status: Malfunction

Exhaust camshaft position actuator solenoid valve control circuit low voltage test status: Malfunction

Exhaust camshaft position actuator solenoid valve control circuit open test status: Malfunction

Ignition coil 1 control circuit high voltage test status: Malfunction

Ignition coil 1 control circuit low voltage test status: Malfunction

Ignition coil 1 control circuit open test status: Malfunction

Ignition coil 2 control circuit high voltage test status: Malfunction

Ignition coil 2 control circuit low voltage test status: Malfunction

Ignition coil 2 control circuit open test status: Malfunction

Ignition coil 3 control circuit high voltage test status: Malfunction

Ignition coil 3 control circuit low voltage test status: Malfunction

Ignition coil 3 control circuit open test status: Malfunction

Ignition coil 4 control circuit high voltage test status: Malfunction

Ignition coil 4 control circuit low voltage test status: Malfunction

Ignition coil 4 control circuit open test status: Malfunction

EVAP purge solenoid valve control circuit high voltage test status: Malfunction

EVAP purge solenoid valve control circuit low voltage test status: Malfunction

EVAP purge solenoid valve control circuit open test status: Malfunction

EVAP vent solenoid valve control circuit high voltage test status: Malfunction

EVAP vent solenoid valve control circuit low voltage test status: Malfunction

EVAP vent solenoid valve control circuit open test status: Malfunction

Cooling fan relay 1 control circuit high voltage test status: Malfunction

Cooling fan relay 1 control circuit low voltage test status: Malfunction

Cooling fan relay 1 control circuit open test status: Malfunction

Camshaft position sensor: 0 rpm

Crankshaft position sensor: 0 rpm

O2 sensor 1, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 1, bank 1 heater: Off

O2 sensor 1, bank 1 heater control circuit open test status: Malfunction

O2 sensor 2, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit open test status: Malfunction

Engine oil pressure sensor: 0 kPa

5V reference voltage circuit 1: 0.00 V

5V reference voltage circuit 2: 0.00 V

Fuel pressure regulator high control circuit command: 0 %

O2 sensor 1, bank 1 heater: 0 %

O2 sensor 1, bank 1 heater: 0.0 A

O2 sensor 2, bank 1 heater: 0.0 A

Engine controls ignition relay control circuit high voltage test status: Malfunction

Engine controls ignition relay control circuit low voltage test status: Malfunction

Engine controls ignition relay control circuit open test status: Malfunction

Engine controls ignition relay feedback signal: 0.0 V

Cruise control: Inactive

Brake booster pressure sensor: 28.00 kPa

A/C disengagement 1st history: None

A/C disengagement 2nd history: None

A/C disengagement 3rd history: None

A/C disengagement 4th history: None

A/C disengagement 5th history: None

A/C disengagement 6th history: None

A/C disengagement 7th history: None

A/C disengagement 8th history: None

Turbocharger bypass solenoid valve control circuit high voltage test status: Malfunction

Turbocharger bypass solenoid valve control circuit low voltage test status: Malfunction

Turbocharger bypass solenoid valve command: Inactive

Turbocharger bypass solenoid valve control circuit open test status: Malfunction

Fuel level sensor reference command: 0 %

EVAP service bay test inhibit reason: None

Engine off evap service bay test abort reason: None

Engine off evap service bay test inhibit reason: None

Engine off evap service bay test result: None

Distance to enable engine off evap service bay test: 0.0 km

Fuel trim system test state: Disabled

Short term fuel trim test average: -100 %

Long term fuel trim test average: -100 %

Long term fuel trim test average without purge: -100 %

Knocking detected, cylinder 4: No

Knocking detected, cylinder 3: No

Knocking detected, cylinder 2: No

Knocking detected, cylinder 1: No

Injector disabled, cylinder 4 - misfire detected: No

Injector disabled, cylinder 3 - misfire detected: No

Injector disabled, cylinder 2 - misfire detected: No

Injector disabled, cylinder 1 - misfire detected: No

Exhaust camshaft position command: 0 %

Intake camshaft position command: 0 %

O2 sensor 2, bank 1 heater: 0 %

Exhaust camshaft target position: 0.0 °

Exhaust camshaft position variance: 0 °

Intake camshaft position variance: 0 °

Exhaust camshaft position active counter: 0 Counts

Intake camshaft position active counter: 0 Counts

Transmission oil temperature: -40 °C

Output shaft speed sensor: 0 rpm

Internal mode switch: --

Engine controls ignition relay feedback 2 signal: 0.0 V

Transmission range command: Undefined

Moving selector lever out of park position: Not allowed

Backup park lock actuator active - system low voltage: No

Parking brake: Unknown state

Park brake request to park brake system: Not requested

P/N switch: Indeterminate

Electric parking brake: Not available

Automatic braking availability: Not available

Automatic braking status: Ok

Engine oil pressure control test counter: 0 Counts

Calculated engine oil pressure: 0 kPa

Oil level warning counter highway: 0

Oil level warning counter country road: 0

Oil level warning counter city: 0

Distance since last oil level warning: 0 km

Distance since last oil pressure warning: 0 km

MAP sensor: 0.00 V

Start-up IAT sensor: -40 °C

Intake air temperature sensor 1 at start: -40 °C

Intake air temperature sensor 2: -40 °C

Barometric pressure sensor: 0.00 V

Clutch pedal position sensor: 0.00 V

Clutch pedal position sensor learned apply position: 0.00 V

Clutch pedal position learn status: Performed successfully

Clutch pedal position sensor learned release position: 0.00 V

Clutch pedal position sensor: 0 %

Service vehicle soon (SVS) indicator command: Off

MIL requested by DTC: No

MIL command: Off

5V reference voltage circuit 4: Ok

5V reference voltage circuit 3: Ok

5V reference voltage circuit 2: Ok

5V reference voltage circuit 5: Ok

5V reference voltage circuit 1: Ok

Fuel composition learn: Inactive

Recommended maximum fuel alcohol content exceeded: No

Fuel economy actual: 0.0 L/h

Replicated transmission OSS signal: 0 rpm

Torque request inhibit - minimum torque: No

Torque request inhibit - fuel: No

Torque request inhibit - TAC limit: No

Torque request inhibit - ignition timing: No

Torque request inhibit - ignition timing advance: No

Torque request inhibit - TAC: No

Torque request inhibit - minimum idle: No

5V reference voltage circuit 3: 0.00 V

5V reference voltage circuit 4: 0.00 V

Engine coolant thermostat heater command: 0.0 %

Engine coolant thermostat heater control circuit high voltage test status: Malfunction

Engine coolant thermostat heater control circuit low voltage test status: Malfunction

Engine coolant thermostat heater control circuit open test status: Malfunction

Radiator coolant temperature sensor: -40 °C

Target engine coolant temperature: -40 °C

Throttle body idle air flow compensation: 0 %

Catalyst monitor test result: No decision

Catalyst monitor not at idle test conditions met: No

Catalyst monitor test state: Inactive

Reduced engine power history: None

Intake air temperature sensor 2: -40 °C

Power mode: Off

Cylinder 1 injector control circuit status: Ok

Cylinder 2 injector control circuit status: Ok

Cylinder 3 injector control circuit status: Ok

Cylinder 4 injector control circuit status: Ok

Fuel pressure regulator control circuit high voltage test status: Malfunction

Fuel pressure regulator control circuit low voltage test status: Malfunction

Fuel pressure regulator control circuit command: Off

Fuel pressure regulator control circuit open test status: Malfunction

Fuel pressure regulator high control circuit high voltage test status: Malfunction

Fuel pressure regulator high control circuit low voltage test status: Malfunction

Fuel pressure regulator high control circuit command: Off

Fuel pressure regulator high control circuit open test status: Malfunction

Fuel rail pressure regulator command: 0 °

MAP sensor: 0 kPa

Ignition coil supply voltage: Off

Recommended maximum fuel alcohol content when recommended maximum fuel alcohol content exceeded: 0 %

Recommended maximum fuel alcohol content: 0 %

Fuel alcohol content when recommended maximum fuel alcohol content exceeded: 0 %

Ambient air temperature when recommended maximum fuel alcohol content exceeded: -40 °C

Ignition cycles since recommended maximum fuel alcohol content exceeded: 0 Counts

Distance since recommended maximum fuel alcohol content exceeded: 0 km

Fuel consumed since recommended maximum fuel alcohol content exceeded: 0 L

Refueling events since recommended maximum fuel alcohol content exceeded: 0 Counts

Fuel composition sensor: 0 Hz

Ignition 1 signal: Off

Ignition accessory signal: Off

Accelerator pedal position sensor 2 - circuit status: Ok

Accelerator pedal position sensor 1 - circuit status: Ok

Brake pedal position sensor: 0.00 V

Brake pedal position sensor learned released position: 0.00 V

Brake pedal position sensor: 0 %

Fuel injector driver supply voltage: 0.0 V

Fuel economy mode: Inactive

Boost pressure: 0 kPa

Calculated barometric pressure: 0 kPa

Intake air temperature sensor 2: 0 Hz

Ambient humidity: 0 %

Intake air humidity sensor: 0 %

Specific humidity: 0.00 %

O2 sensor 1, bank 1: 0.00 V

O2 sensor 2, bank 1: 0.00 V

MAF sensor supply voltage control circuit high voltage test status: Malfunction

MAF sensor supply voltage control circuit low voltage test status: Malfunction

MAF sensor supply voltage command: Off

MAF sensor supply voltage control circuit open test status: Malfunction

Engine oil absolute pressure sensor: 0 kPa

Engine oil pressure: 0 kPa

Engine speed during misfire history 1: 0 rpm

Engine load during misfire history 1: -- %

Engine speed during misfire history 2: 0 rpm

Engine load during misfire history 2: -- %

Engine speed during misfire history 3: 0 rpm

Engine load during misfire history 3: -- %

Engine speed during misfire history 4: 0 rpm

Engine load during misfire history 4: -- %

Target fuel pressure: 0 kPa

Short term fuel pump trim: 0.00

Long term fuel pump trim: 0.00

Fuel pressure sensor: 0.0 V

Fuel pump: 0.00 A

Active grille air shutter 1 position command: 0 %

Active grille air shutter 2 position command: 0 %

Active grille air shutter 1 position: 0 %

Active grille air shutter position: 0 %

Active grille air shutter 2 position: 0 %

EVAP test: Waiting

EVAP test monitor: Undetermined state

Intake manifold pressure: 0 kPa

Fuel rail pressure sensor initial learn: Incomplete

Fuel rail pressure sensor learn: Inactive

Hood position: Closed

Heater coolant pump relay control circuit high voltage test status: Malfunction

Heater coolant pump relay control circuit low voltage test status: Malfunction

Heater coolant pump relay command: Off

Heater coolant pump relay control circuit open test status: Malfunction

Axle torque: -22534 N·m

Driver requested axle torque: -22534 N·m

Fuel rail temperature sensor 1: -40 °C

Fuel rail temperature sensor 2: -40 °C

Start-Up fuel rail temperature 1: -40 °C

Start-Up fuel rail temperature 2: -40.0 °C

Intake camshaft position actuator park lock solenoid valve control circuit high voltage test status: Malfunction

Intake camshaft position actuator park lock solenoid valve control circuit low voltage test status: Malfunction

Intake camshaft position actuator park lock solenoid valve command: On

Intake camshaft position actuator park lock solenoid valve control circuit open test status: Malfunction

Exhaust camshaft position: 0 °

Intake camshaft position: 0 °

Intake camshaft position target: 0 °

Fuel pump driver control module 5V reference 1: 0.00 V

Fuel pump driver control module 5V reference 2: 0.00 V

Fuel pump driver control module 5V reference 2 circuit status: Ok

Fuel pump driver control module 5V reference 1 circuit status: Ok

ISS/OSS supply voltage: Ok

Accelerator pedal position sensor 1 learned applied position: 0 %

Accelerator pedal position sensor 2 learned applied position: 0 %

Neutral position sensor: 0.0 %

Neutral position sensor: Neutral

Intake air temperature sensor 2 at start: -40 °C

Boost pressure sensor: 0.00 V

Auxiliary coolant pump relay command: Inactive

Target fuel rail pressure: 0.0 MPa

Fuel rail pressure sensor: 0.00 V

Current gear: Unknown

Accelerator pedal position sensor 1 learned released position: 0.00 V

Accelerator pedal position sensor 2 learned released position: 0.00 V

Target booster pressure: 0 kPa

Turbocharger wastegate solenoid valve command: 0 %

Turbocharger bypass solenoid valve command: 0 %

Boost pressure sensor: 0 kPa

Engine oil pressure control solenoid valve control circuit high voltage test status: Malfunction

Engine oil pressure control solenoid valve control circuit low voltage test status: Malfunction

Engine oil pressure control solenoid valve command: High pressure

Engine oil pressure control solenoid valve control circuit open test status: Malfunction

Intake air temperature sensor 3 at start: -40 °C

Battery voltage: 0.0 V

Battery voltage: 0.0 V

Transmission accumulator solenoid valve control circuit high voltage test status: Malfunction

Transmission accumulator solenoid valve control circuit low voltage test status: Malfunction

Transmission accumulator solenoid valve command: Off

Transmission accumulator solenoid valve control circuit open test status: Malfunction

Distance since excessive clutch slip detected: 0 km

Fuel rail temperature sensor 1: 0 Counts

Fuel rail temperature sensor 2: 0 Counts

5V reference voltage circuit 5: 0.00 V

5V reference voltage circuit 5: 0.00 V

Backup park lock position: Drive

Backup park lock status: Standby

Selector lever position send by chassis control module to transmission range control module: None

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Reduced engine power: Inactive

A/C request: No

A/C compressor operation: Not allowed

Brake pedal position sensor signal: No

Clutch pedal starter inhibit switch: On

Clutch pedal switch: Released

Reverse position switch: Off

Starter relay command: Off

Ignition 1 signal: 0.00 V

Generator F terminal signal: 0.0 %

Target idle speed: 0 rpm

Accelerator pedal position: 0 %

Generator L - terminal command: 0.0 %

Engine controls ignition relay feedback signal: 0.0 V

Brake booster pressure sensor: 28.00 kPa

Auxiliary transmission fluid pump relay command: Off

MIL requested by DTC: No

Reduced engine power history: None

Power mode: Off

MAP sensor: 0 kPa

Ignition accessory signal: Off

Stop/Start disable mode: Inactive

Intake manifold pressure: 0 kPa

Hood position: Closed

System OFF: No

Stop/start system status:

Autostop disable reason - hood ajar: No

Autostop disable reason - ECM request: No

Autostop disable reason - run/crank not active: No

Autostop disable reason - acceleration request: No

Autostop disable reason - minimum engine run time not met: No

Autostop disable reason - control function active: No

Autostop disable reason - ignition switch start: No

Autostop disable reason - engine coolant temperature out of range: No

Autostop disable reason - system optimization: No

Autostop disable reason - transmission in reverse: No

Autostop disable reason - system voltage low: No

Autostop disable reason - invalid data received: No

Autostop disable reason - vehicle speed too high: No

Autostop disable reason - reduced engine power active: No

Autostart inhibit reason - hood ajar: No

Autostart inhibit reason - ECM request: No

Autostart inhibit reason - run/crank not active: No

Autostart inhibit reason - system malfunction: No

Autostart inhibit reason - control function active: No

Autostart inhibit reason - autostart not commanded: No

Autostart inhibit reason - ECM malfunction: No

Autostart inhibit reason - crank aborted: No

Autostart inhibit reason - autostart/autostop malfunction: No

Autostart inhibit reason - driver exited vehicle: No

Autostart inhibit reason - engine coolant temperature out of range: No

Autostart reason - maximum autostop time exceeded: No

Autostart reason - reduced engine power active: No

Autostart reason - system malfunction: No

Autostart reason - system optimization: No

Autostart reason - transmission in reverse: No

Autostart reason - system voltage low: No

Autostart reason - invalid data received: No

Autostart reason - vehicle speed too high: No

Autostart reason - acceleration request: No

Autostart reason - minimum engine run time not met: No

Autostart reason - control function active: No

Autostart reason - ignition switch start: No

Autostart reason - engine coolant temperature out of range: No

Autostart reason - hood ajar: No

Autostart reason - ECM request: No

Autostop disable reason - 12V start counter exceeded: No

Autostop disable reason - brake pedal released: No

Autostop disable reason - vehicle inclination: No

Autostop disable reason - brake booster weak vacuum: No

Autostop disable reason - A/C request: No

Autostop disable reason - accelerator pedal pressed: No

Autostop disable reason - low-voltage battery voltage low: No

Autostop disable reason - low-voltage battery state of health low: No

Autostop disable reason - engine speed high: No

Autostop disable reason - low-voltage battery state of charge low: No

Autostop disable reason - wheel slip detected: No

Autostop disable reason - low-voltage battery discharge current high: No

Autostop disable reason - vehicle speed threshold not reached: No

Autostop disable reason - intake manifold weak vacuum: No

Autostop disable reason - maximum vehicle stop time exceeded: No

Autostop disable reason - starter system malfunction: No

Autostop disable reason - generator load high: No

Autostop disable reason - clutch pedal applied: No

Autostop disable reason - stop/start select switch: No

Autostop disable reason - low-voltage battery temperature out of range: No

Autostop disable reason - idle boost mode active: No

Autostop disable reason - low-voltage battery state of function low: No

Autostart reason - low-voltage battery discharge current high: No

Autostart reason - brake pedal released: No

Autostart Reason - inclination: No

Autostart reason - brake booster weak vacuum: No

Autostart reason - A/C request: No

Autostart reason - accelerator pedal pressed: No

Autostart reason - low-voltage battery voltage low: No

Autostart reason - clutch pedal applied: No

Autostart reason - low-voltage battery state of function low: No

Autostart reason - driver exited vehicle: No

Autostart reason - low-voltage battery state of health low: No

Autostart reason - stop/start select switch: No

Autostart reason - low-voltage battery state of charge low: No

Neutral position sensor: Neutral

Autostop disable reason - system malfunction: --

DC/DC converter engine crank signal input: No

Engine crank command: No

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Baro: 0.0 kPa

Reduced engine power: Inactive

A/C request: No

A/C compressor operation: Not allowed

Brake pedal position circuit signal: Released

Starter relay command: Off

Remote vehicle start request signal: Off

Ignition 1 signal: 0.00 V

Generator F terminal signal: 0.0 %

Engine oil temperature calculated: -40 °C

Target idle speed: 0 rpm

Accelerator pedal position: 0 %

Generator L - terminal command: 0.0 %

Engine controls ignition relay feedback signal: 0.0 V

Brake booster pressure sensor: 28.00 kPa

Engine controls ignition relay feedback 2 signal: 0.0 V

P/N switch: Indeterminate

MIL requested by DTC: No

Catalyst monitor test state: Inactive

Reduced engine power history: None

Reduced engine power history: None

MAP sensor: 0 kPa

Ignition 1 signal: Off

Ignition accessory signal: Off

EVAP test: Waiting

Intake manifold pressure: 0 kPa

Hood position: Closed

Engine stopping: No

System OFF: No

Engine running: No

Engine off: No

Engine starting: No

Engine stalled: No

Engine autostopped: No

Autostop disable reason - hood ajar: No

Autostop disable reason - ECM request: No

Autostop disable reason - run/crank not active: No

Autostop disable reason - acceleration request: No

Autostop disable reason - auxiliary transmission fluid pump/accumulator not available: No

Autostop disable reason - minimum engine run time not met: No

Autostop disable reason - control function active: No

Autostop disable reason - ignition switch start: No

Autostop disable reason - engine coolant temperature out of range: No

Autostop disable reason - engine coolant temperature out of range: No

Autostop disable reason - remote vehicle start request: No

Autostop disable reason - system optimization: No

Autostop disable reason - transmission in reverse: No

Autostop disable reason - system voltage low: No

Autostop disable reason - invalid data received: No

Autostop disable reason - vehicle speed too high: No

Autostop disable reason - Hybrid/EV battery pack temperature: No

Autostop disable reason - TCM request: No

Autostop disable reason - reduced engine power active: No

Autostop disable reason - transmission range: No

Autostop disable reason - transmission range: No

Autostart inhibit reason - hood ajar: No

Autostart inhibit reason - ECM request: No

Autostart inhibit reason - run/crank not active: No

Autostart inhibit reason - system malfunction: No

Autostart inhibit reason - control function active: No

Autostart inhibit reason - autostart not commanded: No

Autostart inhibit reason - ECM malfunction: No

Autostart inhibit reason - crank aborted: No

Autostart inhibit reason - autostart/autostop malfunction: No

Autostart inhibit reason - compression test: No

Autostart inhibit reason - engine stop required: No

Autostart inhibit reason - TCM request: No

Autostart inhibit reason - remote vehicle start disabled: No

Autostart inhibit reason - driver exited vehicle: No

Autostart inhibit reason - engine coolant temperature out of range: No

Autostart inhibit reason - calibration override: No

Autostart reason - maximum autostop time exceeded: No

Autostart reason - transmission fluid temperature out of range: No

Autostart reason - TCM demand: No

Autostart reason - reduced engine power active: No

Autostart reason - system malfunction: No

Autostart reason - remote vehicle start request: No

Autostart reason - system optimization: No

Autostart reason - transmission in reverse: No

Autostart reason - system voltage low: No

Autostart reason - invalid data received: No

Autostart reason - vehicle speed too high: No

Autostart reason - acceleration request: No

Autostart reason - auxiliary transmission fluid pump/accumulator not available: No

Autostart reason - minimum engine run time not met: No

Autostart reason - control function active: No

Autostart reason - ignition switch start: No

Autostart reason - engine coolant temperature out of range: No

Autostart reason - transmission range: No

Autostart reason - hood ajar: No

Autostart reason - ECM request: No

Autostop disable reason - 12V start counter exceeded: No

Autostop disable reason - brake pedal released: No

Autostop disable reason - vehicle inclination: No

Autostop disable reason - brake booster weak vacuum: No

Autostop disable reason - A/C request: No

Autostop disable reason - accelerator pedal pressed: No

Autostop disable reason - low-voltage battery voltage low: No

Autostop disable reason - low-voltage battery state of health low: No

Autostop disable reason - engine speed high: No

Autostop disable reason - low-voltage battery state of charge low: No

Autostop disable reason - wheel slip detected: No

Autostop disable reason - low-voltage battery discharge current high: No

Autostop disable reason - vehicle speed threshold not reached: No

Autostop disable reason - intake manifold weak vacuum: No

Autostop disable reason - maximum vehicle stop time exceeded: No

Autostop disable reason - starter system malfunction: No

Autostop disable reason - generator load high: No

Autostop disable reason - clutch pedal applied: No

Autostop disable reason - stop/start select switch: No

Autostop disable reason - low-voltage battery temperature out of range: No

Autostop disable reason - idle boost mode active: No

Autostop disable reason - low-voltage battery state of function low: No

Autostop disable reason - passenger compartment heater on: No

Autostop disable reason - driver exited vehicle: No

Autostart reason - low-voltage battery discharge current high: No

Autostart reason - brake pedal released: No

Autostart Reason - inclination: No

Autostart reason - brake booster weak vacuum: No

Autostart reason - A/C request: No

Autostart reason - accelerator pedal pressed: No

Autostart reason - low-voltage battery voltage low: No

Autostart reason - clutch pedal applied: No

Autostart Reason - passenger compartment heater on: No

Autostart reason - low-voltage battery state of function low: No

Autostart reason - driver exited vehicle: No

Autostart reason - low-voltage battery state of health low: No

Autostart reason - stop/start select switch: No

Autostart reason - low-voltage battery state of charge low: No

Low-voltage battery current: 0.00 A

Low-voltage battery temperature: -40 °C

Low-voltage battery state of function: 0.00 V

Low-voltage battery state of health: 0 %

Low-voltage battery state of charge: 0.0 %

Fuel rail temperature sensor 1: -40 °C

Engine crank time: 0 ms

Battery voltage high resolution: 0.00 V

Battery voltage: 0.0 V

Starter pinion solenoid actuator relay command: Off

Transmission accumulator solenoid valve command: Off

Battery type: Default

Battery capacity: 0.00 Ah

Autostop disable reason - parking maneuver detected: No

Autostop disable reason - MAF sensor test in progress: No

Autostop disable reason - MAP sensor test in progress: No

Autostop disable reason - barometric pressure too low: No

Autostop disable reason - fuel temperature too high: No

Autostop disable reason - high engine rotating torque: No

Autostop disable reason - O2 sensor test in progress: --

Autostop disable reason - misfire test in progress: --

Autostop disable reason - engine speed test in progress: --

Autostop disable reason - EVAP system test in progress: --

Autostop disable reason - system malfunction: --

Autostop disable reason - system malfunction: --

Autostop disable reason - engine coolant temperature test in progress: --

Autostop disable reason - fuel injector test in progress: --

Autostop disable reason - catalyst test in progress: --

Autostop disable reason - catalyst not at operating temperature: --

Autostop disable reason - engine oil temperature too high: --

Autostop disable reason - intake manifold temperature too high: --

Autostop disable reason - fuel system test in progress: --

Autostop disable reason - turbocharger temperature too high: --

Autostop disable reason - fuel pressure test in progress: --

Autostop disable reason - engine stop/start test in progress: --

DC/DC converter output voltage 2 performance test status - engine cranking: Inactive

DC/DC converter ignition 1 signal: Off

DC/DC converter output voltage 1 performance test status - engine cranking: Inactive

DC/DC converter output voltage 2 performance test status - engine running / off: Inactive

DC/DC converter engine crank signal input: No

DC/DC converter output voltage 1 performance test status - engine running / off: Inactive

Filtered system voltage: 0.0 V

Filtered system voltage prior to engine crank: 0.0 V

DC/DC converter output voltage sensor circuit 1: 0.0 V

DC/DC converter output voltage sensor circuit 2: 0.0 V

DC/DC converter output voltage 1 variance - engine running / off: 0.0 V

DC/DC converter output voltage 2 variance - engine running / off: 0.0 V

DC/DC converter output voltage 1 variance - engine cranking: 0.0 V

DC/DC converter output voltage 2 variance - engine cranking: 0.0 V

Minimum filtered system voltage - last engine crank: 0.00 V

Minimum DC/DC converter output voltage on circuit 1 - last engine crank: 0.0 V

Minimum DC/DC converter output voltage on circuit 2 - last engine crank: 0.0 V

Battery sensor module battery state information: Not available

Battery sensor module reset occurred - using estimated state of charge: No

Engine hood switch: Closed

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Target throttle position: 0 %

Brake pedal position sensor signal: No

Extended travel brake pedal position signal: Released

Brake pedal position circuit signal: Released

Clutch pedal switch: Released

Engine oil level switch: Ok

Starter relay command: Off

Ignition 1 signal: 0.00 V

Brake booster pressure sensor: 0.0 V

Torque management ignition timing retard: 0.0 °

Target idle speed: 0 rpm

Throttle position: 0 %

Cruise control disengagement 1st history: Brake pedal applied

Cruise control disengagement 2nd history: Brake pedal applied

Cruise control disengagement 3rd history: Brake pedal applied

Cruise control disengagement 4th history: Brake pedal applied

Cruise control disengagement 5th history: Brake pedal applied

Cruise control disengagement 6th history: Brake pedal applied

Cruise control disengagement 7th history: Brake pedal applied

Cruise control disengagement 8th history: Brake pedal applied

Accelerator pedal position: 0 %

Torque delivered signal: 0 N·m

Cruise control "On"/"Off" switch: Off

Cruise control "Set/Coast" switch: Off

Cruise control "Cancel" switch: Inactive

Cruise control "Resume/Accelerate" switch: Off

Cruise control: Inactive

Brake booster pressure sensor: 28.00 kPa

Replicated transmission OSS signal: 0 rpm

Cruise control inhibit reason: Brake pedal applied

Cruise control switch: Undetermined state

Hood position: Closed

Driver requested axle torque: -22534 N·m

Battery voltage: 0.0 V

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Brake pedal position sensor signal: No

Brake pedal position circuit signal: Released

Clutch pedal starter inhibit switch: On

Starter relay command: Off

Engine controls ignition relay command: Off

Remote vehicle start request signal: Off

Crank request signal: No

Ignition 1 signal: 0.00 V

Generator F terminal signal: 0.0 %

Accelerator pedal position: 0 %

Starter relay control circuit high voltage test status: Malfunction

Starter relay control circuit low voltage test status: Malfunction

Starter relay control circuit open test status: Malfunction

Generator L - terminal command: 0.0 %

Engine controls ignition relay control circuit high voltage test status: Malfunction

Engine controls ignition relay control circuit low voltage test status: Malfunction

Engine controls ignition relay control circuit open test status: Malfunction

Engine controls ignition relay feedback signal: 0.0 V

Generator L-terminal circuit high voltage test status: Malfunction

Generator L-terminal circuit low voltage test status: Malfunction

Generator L - terminal command: Off

Generator L-terminal circuit open test status: Malfunction

Remote vehicle start disable history 1: None

Remote vehicle start disable history 2: None

Remote vehicle start disable history 3: None

Remote vehicle start disable history 4: None

Remote vehicle start disable history 5: None

Remote vehicle start disable history 6: None

Remote vehicle start disable history 7: None

Remote vehicle start disable history 8: None

ECM response source: Ignition switch start

ECM authentication status: Unknown

ECM challenge status: Invalid

Immobilizer security information programmed: No

Immobilizer system status: Standby

Immobilizer password learn : Inactive

Immobilizer security code accepted: No

Immobilizer security code function: Not present

Immobilizer security code programmed: No

Immobilizer security code lockout: No

Immobilizer password learn scan tool delay: Inactive

Immobilizer auto learn counter: 0

Immobilizer automatic learn timer: 0 sec

P/N switch: Indeterminate

MIL requested by DTC: No

Immobilizer valid response received time: 0 ms

Power mode: Off

Ignition 1 signal: Off

Ignition accessory signal: Off

Engine oil pressure: 0 kPa

Hood position: Closed

Low-voltage battery current: 0.00 A

Low-voltage battery temperature: -40 °C

Low-voltage battery state of function: 0.00 V

Low-voltage battery state of health: 0 %

Low-voltage battery state of charge: 0.0 %

Battery voltage high resolution: 0.00 V

Battery voltage: 0.0 V

Starter pinion solenoid actuator relay command: Off

Immobilizer security code lockout active timer: 0 ms

Immobilizer security code programming counter: 0 Counts

Immobilizer security code reset counter: 0 Counts

VIN programing counter: 0

Maximum engine speed when engine overspeed detected: 0.0 rpm

Engine speed when engine overspeed detected: 0.0 rpm

Vehicle speed when engine overspeed detected: 0 km/h

Accelerator pedal position when engine overspeed detected: 0.0 %

Engine oil temperature when engine overspeed detected: -40 °C

Current gear when engine overspeed detected: Unknown

MAF when engine overspeed detected: 0.00 g/sec

Odometer when engine overspeed detected: 0 km

Engine overspeed counter: 0 Counts

Engine overspeed: Not present

Total engine overspeed time: 0 ms

Calibration history buffer: Unlocked

Engine calibration part number history 1: --

Calibration verification number history 1: --

Engine calibration part number history 1 counter: --

Engine calibration part number history 2: --

Calibration verification number history 2: --

Engine calibration part number history 2 counter: --

Engine calibration part number history 3: --

Calibration verification number history 3: --

Engine calibration part number history 3 counter: --

Engine calibration part number history 4: --

Calibration verification number history 4: --

Engine calibration part number history 4 counter: --

Engine calibration part number history 5: --

Calibration verification number history 5: --

Engine calibration part number history 5 counter: --

Engine calibration part number history 6: --

Calibration verification number history 6: --

Engine calibration part number history 6 counter: --

Engine calibration part number history 7: --

Calibration verification number history 7: --

Engine calibration part number history 7 counter: --

Engine calibration part number history 8: --

Calibration verification number history 8: --

Engine calibration part number history 8 counter: --

Engine calibration part number history 9: --

Calibration verification number history 9: --

Engine calibration part number history 9 counter: --

Engine calibration part number history 10: --

Calibration verification number history 10: --

Engine calibration part number history 10 counter: --

VIN no: --

Engine load: 0.0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim: -100 %

Long term fuel trim: -100 %

Fuel pressure sensor: 0 kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Intake air temperature sensor 1: -40 °C

Mass air flow sensor: 0.00 g/sec

Fuel rail pressure sensor: 0.0 MPa

EVAP purge solenoid valve command: 0 %

Remaining fuel in tank: 0.0 %

Warm-ups since DTC cleared: 0 Counts

Fuel tank pressure sensor: 0.00 in. H2O

Baro: 0.0 kPa

Calculated catalyst temperature: -40 °C

Air/Fuel equivalence ratio command: 0.00

Air/Fuel equivalence ratio command: 0.00 lambda

Ambient air temperature: -40 °C

Target throttle position: 0 %

Fuel alcohol content: 0 %

A/C request: No

A/C cut-off due to A/C pressure out of range: No

A/C Off for WOT: No

A/C compressor operation: Not allowed

Brake pedal position sensor signal: No

Brake pedal position circuit signal: Released

Clutch pedal starter inhibit switch: On

Upshift Indicator command: Off

Clutch pedal switch: Released

Reverse position switch: Off

O2 sensor 2, bank 1 heater: Off

Engine oil pressure switch: Ok

Change engine oil indicator command: Off

Low engine oil level indicator command: Off

Low engine oil pressure indicator command: Off

Engine oil level switch: Ok

Fuel volatility: Low

Cold start: No

Crank request signal: No

Fuel enrichment - hot catalyst: No

Fuel enrichment - hot coolant: Inactive

Power enrichment: Inactive

Fuel control loop status: Open

Deceleration fuel cut-off: Inactive

Fuel trim learn: Disabled

Ignition 1 signal: 0.00 V

Coolant temperature at engine start: -40 °C

Fuel trim memory cell: 0

Target idle speed: 0 rpm

Distance since DTC cleared: 0 km

Distance since first malfunction: 0 km

Distance since last malfunction: 0 km

Ignition cycles with malfunction since 1st malfunction: 0 Counts

Ignition cycles without malfunction since last malfunction: 0 Counts

Ignition cycles without completed test since 1st malfunction: 0 Counts

Accelerator pedal position sensors: 0 %

Throttle position: 0 %

Injection time bank 1: 0.00 ms

Total knock retard: 0 °

Accelerator pedal position: 0 %

Remaining fuel in tank: 0 L

Torque delivered signal: 0 N·m

Engine off time: 00:00:00

Camshaft position sensor: 0 rpm

Crankshaft position sensor: 0 rpm

O2 sensor 1, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 1, bank 1 heater: Off

O2 sensor 1, bank 1 heater control circuit open test status: Malfunction

O2 sensor 2, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit open test status: Malfunction

5V reference voltage circuit 1: 0.00 V

5V reference voltage circuit 2: 0.00 V

Cruise control "On"/"Off" switch: Off

Cruise control "Set/Coast" switch: Off

Cruise control "Cancel" switch: Inactive

Cruise control "Resume/Accelerate" switch: Off

Cruise control: Inactive

ECM response source: Ignition switch start

ECM authentication status: Unknown

ECM challenge status: Invalid

Immobilizer security information programmed: No

Immobilizer password learn : Inactive

Knocking detected, cylinder 4: No

Knocking detected, cylinder 3: No

Knocking detected, cylinder 2: No

Knocking detected, cylinder 1: No

Exhaust camshaft target position: 0.0 °

A/T output speed: 0 rpm

P/N switch: Indeterminate

Start-up IAT sensor: -40 °C

Intake air temperature sensor 2: -40 °C

5V reference voltage circuit 3: 0.00 V

5V reference voltage circuit 4: 0.00 V

Immobilizer valid response received time: 0 ms

Power mode: Off

MAP sensor: 0 kPa

Ignition accessory signal: Off

O2 sensor 1, bank 1: 0.00 V

O2 sensor 2, bank 1: 0.00 V

Exhaust camshaft position: 0 °

Intake camshaft position: 0 °

Intake camshaft position target: 0 °

ISS/OSS supply voltage: Ok

Engine coolant temperature sensor: -40 °C

Vehicle speed sensor: 0 km/h

Intake air temperature sensor 1: -40 °C

Remaining fuel in tank: 0.0 %

Baro: 0.0 kPa

Catalyst monitor enabled this ignition cycle: --

O2S/HO2S monitor enabled this ignition cycle: --

EVAP monitor enabled this ignition cycle: --

HO2S heater monitor enabled this ignition cycle: --

EGR/Camshaft position monitor enabled this ignition cycle: --

Catalyst monitor complete this ignition cycle: --

O2S/HO2S monitor complete this ignition cycle: --

EVAP monitor complete this ignition cycle: --

HO2S heater monitor complete this ignition cycle: --

EGR/Camshaft position monitor complete this ignition cycle: --

Ambient air temperature: -40 °C

Fuel alcohol content: 0 %

Brake pedal position sensor signal: No

Brake pedal position circuit signal: Released

Clutch pedal switch: Released

Cold start: No

Ignition 1 signal: 0.00 V

Coolant temperature at engine start: -40 °C

Remaining fuel in tank: 0 L

Engine off time: 00:00:00

Start-up IAT sensor: -40 °C

MIL requested by DTC: No

MIL command: Off

Calculated barometric pressure: 0 kPa

Inspection/Maintenance drive cycle vehicle speed time complete: No

Inspection/Maintenance drive cycle propulsion system active time complete: No

Inspection/Maintenance drive cycle idle time complete: No

Number of DTC: --

Check engine telltale request: --

Misfire monitor enabled: --

Misfire monitor complete: --

Fuel system monitor enabled: --

Fuel system monitor complete: --

Component monitor enabled: --

Component monitor complete: --

Catalyst monitor enabled: --

Catalyst monitor enabled: --

O2S/HO2S monitor enabled: --

EVAP monitor enabled: --

HO2S heater monitor enabled: --

Secondary air injection system monitor enabled: --

EGR/Camshaft position monitor enabled: --

Catalyst monitor complete: --

Catalyst monitor complete: --

O2S/HO2S monitor complete: --

EVAP monitor complete: --

HO2S heater monitor complete: --

Secondary air injection system monitor complete: --

EGR/Camshaft position monitor complete: --

Fuel pressure drop - cylinder 1 injector: -- kPa

Fuel pressure drop - cylinder 2 injector: -- kPa

Fuel pressure drop - cylinder 3 injector: -- kPa

Fuel pressure drop - cylinder 4 injector: -- kPa

A/C compressor clutch relay

Exhaust camshaft position actuator

Intake camshaft position actuator

Intake camshaft position actuator solenoid valve

Exhaust camshaft position actuator solenoid valve

Cooling fan

Engine oil pressure control solenoid valve

Engine speed

Throttle position

Evaporative emission (EVAP) system, canister purge valve

Evaporative emission (EVAP) system, canister vent valve

EVAP purge/seal

Fuel control loop status

Cylinder power balance

Depressurize fuel system

Fuel injector balance

Fuel pump enable

Fuel trim enable

Fuel pressure

Generator L terminal

Ignition timing retard

Check engine telltale

Crankshaft position variation learn

HO2S heater learn

Ambient air temperature calculation reset

Reset oil life

Fuel rail pressure relief valve learned values reset

Fuel trim reset

Intake system learned values reset

Throttle body idle air flow compensation reset

Brake pedal position sensor learn

Remote vehicle start disable history reset