Bil, ACURA, EL, Robotized gearbox (i-SHIFT)

transakse - Robotized gearbox (i-SHIFT) - 0

Identifikation

Identificere : 00 08 40 40 10

Dele nummer: 28125-RPJ-L070

Fejlkoder

P0603: Internal control module keep alive memory (KAM) error

P0974: Ukendt fejlkode

P0977: Ukendt fejlkode

P0980: Ukendt fejlkode

P0983: Ukendt fejlkode

P0108: Ukendt fejlkode

U0028: Ukendt fejlkode

P0713: Ukendt fejlkode

P2122: Ukendt fejlkode

Controls

Clear DTC

Levende Data

Motordrejningsmoment: -86.35 N·m

Accelerator pedal position sensor: 5.64 °

Target idle speed: 854 Omdr.

Clutch slip: -8635 Omdr.

Venstre forhjulshastighedsføler: 13398 Omdr.

Højre forhjulshastighedsføler: 63487 Omdr.

Venstre baghjuls hastighedsføler: 30019 Omdr.

Højre baghjulshastighedsføler: 10121 Omdr.

Systemspænding: 655.35 V

Clutch temperature: 65535 °C

Motor Hastighed: 1110 Omdr.

Clutch actuator temperature: -8636 °C

TCM power circuit board temperature: 853 °C

Intake air temperature sensor: 837 °C

Motor kølevæske temperatur føler: 69

Brake pedal switch normally open: Tænd

Brake pedal switch normally closed: Sluk

Brake switch AND signal: Tænd

Wheel speed: 13944 Omdr.

Transmission gear command: 1

Gear position (current): 1

HAC switch (CAN): Sluk

Starter operation command: Sluk

ABS state: Ikke aktiv

Fartpilot: Ikke aktiv

VSA system: Equip

VSA status: Ikke aktiv

Cruise control shift down request 1: Sluk

Cruise control shift down request 2: Sluk

Ignition switch (input): Tænd

Buzzer request: Sluk

Kobling i lukket position: Åben

Auto mode gauge display: Tænd

i-SHIFT telltale: Tænd

Creep control system: Ikke aktiv

Starter enable signal: Deaktiver

Bremsepedalkontakt: Tænd

Clutch open position: Åben

Clutch contact position 1 learning condition: Learnt

Clutch contact position 2 learning condition: Learnt

Clutch contact position 3 learning condition: Learnt

Learnt end position gear 1: Learnt

Learnt end position gear 2: Learnt

Learnt end position gear 3: Learnt

Learnt end position gear 4: Learnt

Learnt end position gear 5: Learnt

Learnt end position gear 6: Learnt

Learnt end position gear reverse: Learnt

Learnt synchronizer position gear 1: Learnt

Learnt synchronizer position gear 2: Learnt

Learnt synchronizer position gear 3: Learnt

Learnt synchronizer position gear 4: Learnt

Learnt synchronizer position gear 5: Learnt

Learnt synchronizer position gear 6: Learnt

All outputs valid: Deaktiver

Hardware valid: Aktiver

Steering wheel downshift (-) switch command: Aktiver

Steering wheel upshift (+) switch command: Aktiver

Shift valid - A/M: Gyldig

Shift valid D: Gyldig

Shift valid N: Gyldig

Shift valid R: Gyldig

Steering shiftmatic down switch: Sluk

Steering shiftmatic up switch: Sluk

Manual mode: AUTO

Drive: Tænd

Neutral: Tænd

Reverse: Sluk

Shifter in middle of R and N position: Sluk

Shifter in middle of D and N position: Sluk

Gear lever position - tip minus: Sluk

Gear lever position - tip plus: Sluk

Gear lever position - drive: Tænd

Gear lever position - A/M: Sluk

Gear lever position - neutral: Sluk

Gear lever position - reverse: Sluk

Long term clutch contact point learned value: 14.00 mm

Medium term clutch contact point learned value: 172.20 mm

Short term clutch contact point learned value: 93.01 mm

Target clutch position: 569.01 mm

Actual clutch position: 491.51 mm

Shift position gear 1: 23.00 mm

Shift position gear 2: 4.00 mm

Shift position gear 3: 18.92 mm

Shift position gear 4: -86.36 mm

Shift position gear 5: 46.59 mm

Shift position gear 6: -73.39 mm

Reverse gear position (shift): 300.01 mm

Select position gear 1: -0.02 mm

Select position gear 2: 221.35 mm

Select position gear 3: -4.44 mm

Select position gear 4: 9.09 mm

Select position gear 5: -8.00 mm

Select position gear 6: 12.00 mm

Reverse gear position (select): -6.00 mm

Neutral gear position (select): 5.64 mm

Learnt synchronizer position gear 1: 0.19 mm

Learnt synchronizer position gear 2: -6.91 mm

Learnt synchronizer position gear 3: -5.00 mm

Learnt synchronizer position gear 4: -6.89 mm

Learnt synchronizer position gear 5: 8.21 mm

Learnt synchronizer position gear 6: 1.11 mm

Friction coefficient 1: 699

Friction coefficient 2: 699

Friction coefficient 3: 699

General friction coefficient: 695

Gate width gear 1: 11.10 mm

Gate width gear 2: -86.35 mm

Gate width gear 3: -70.82 mm

Gate width gear 4: 265.12 mm

Gate width gear 5: 136.88 mm

Gate width gear 6: 54.79 mm

Gate width gear R: -71.45 mm

Muligheder

Controls

Clutch fluid filling

Clutch fluid air bleeding

Static mode learning

Dynamic mode learning

Shift motor calibration

Engage gear test

Clutch actuator full stroke operation test

Gear box self test