Bil, ACURA, TL, Robotized gearbox (i-SHIFT)

Identificere : 00 08 40 40 10

Dele nummer: 28125-RPJ-L070

P0603: Internal control module keep alive memory (KAM) error

P0974: Ukendt fejlkode

P0977: Ukendt fejlkode

P0980: Ukendt fejlkode

P0983: Ukendt fejlkode

P0108: Ukendt fejlkode

U0028: Ukendt fejlkode

P0713: Ukendt fejlkode

P2122: Ukendt fejlkode

Clear DTC

Motordrejningsmoment: -86.35 N·m

Accelerator pedal position sensor: 5.64 °

Target idle speed: 854 Omdr.

Clutch slip: -8635 Omdr.

Venstre forhjulshastighedsføler: 13398 Omdr.

Højre forhjulshastighedsføler: 63487 Omdr.

Venstre baghjuls hastighedsføler: 30019 Omdr.

Højre baghjulshastighedsføler: 10121 Omdr.

Systemspænding: 655.35 V

Clutch temperature: 65535 °C

Motor Hastighed: 1110 Omdr.

Clutch actuator temperature: -8636 °C

TCM power circuit board temperature: 853 °C

Intake air temperature sensor: 837 °C

Motor kølevæske temperatur føler: 69

Brake pedal switch normally open: Tænd

Brake pedal switch normally closed: Sluk

Brake switch AND signal: Tænd

Wheel speed: 13944 Omdr.

Transmission gear command: 1

Gear position (current): 1

HAC switch (CAN): Sluk

Starter operation command: Sluk

ABS state: Ikke aktiv

Fartpilot: Ikke aktiv

VSA system: Equip

VSA status: Ikke aktiv

Cruise control shift down request 1: Sluk

Cruise control shift down request 2: Sluk

Ignition switch (input): Tænd

Buzzer request: Sluk

Kobling i lukket position: Åben

Auto mode gauge display: Tænd

i-SHIFT telltale: Tænd

Creep control system: Ikke aktiv

Starter enable signal: Deaktiver

Bremsepedalkontakt: Tænd

Clutch open position: Åben

Clutch contact position 1 learning condition: Learnt

Clutch contact position 2 learning condition: Learnt

Clutch contact position 3 learning condition: Learnt

Learnt end position gear 1: Learnt

Learnt end position gear 2: Learnt

Learnt end position gear 3: Learnt

Learnt end position gear 4: Learnt

Learnt end position gear 5: Learnt

Learnt end position gear 6: Learnt

Learnt end position gear reverse: Learnt

Learnt synchronizer position gear 1: Learnt

Learnt synchronizer position gear 2: Learnt

Learnt synchronizer position gear 3: Learnt

Learnt synchronizer position gear 4: Learnt

Learnt synchronizer position gear 5: Learnt

Learnt synchronizer position gear 6: Learnt

All outputs valid: Deaktiver

Hardware valid: Aktiver

Steering wheel downshift (-) switch command: Aktiver

Steering wheel upshift (+) switch command: Aktiver

Shift valid - A/M: Gyldig

Shift valid D: Gyldig

Shift valid N: Gyldig

Shift valid R: Gyldig

Steering shiftmatic down switch: Sluk

Steering shiftmatic up switch: Sluk

Manual mode: AUTO

Drive: Tænd

Neutral: Tænd

Reverse: Sluk

Shifter in middle of R and N position: Sluk

Shifter in middle of D and N position: Sluk

Gear lever position - tip minus: Sluk

Gear lever position - tip plus: Sluk

Gear lever position - drive: Tænd

Gear lever position - A/M: Sluk

Gear lever position - neutral: Sluk

Gear lever position - reverse: Sluk

Long term clutch contact point learned value: 14.00 mm

Medium term clutch contact point learned value: 172.20 mm

Short term clutch contact point learned value: 93.01 mm

Target clutch position: 569.01 mm

Actual clutch position: 491.51 mm

Shift position gear 1: 23.00 mm

Shift position gear 2: 4.00 mm

Shift position gear 3: 18.92 mm

Shift position gear 4: -86.36 mm

Shift position gear 5: 46.59 mm

Shift position gear 6: -73.39 mm

Reverse gear position (shift): 300.01 mm

Select position gear 1: -0.02 mm

Select position gear 2: 221.35 mm

Select position gear 3: -4.44 mm

Select position gear 4: 9.09 mm

Select position gear 5: -8.00 mm

Select position gear 6: 12.00 mm

Reverse gear position (select): -6.00 mm

Neutral gear position (select): 5.64 mm

Learnt synchronizer position gear 1: 0.19 mm

Learnt synchronizer position gear 2: -6.91 mm

Learnt synchronizer position gear 3: -5.00 mm

Learnt synchronizer position gear 4: -6.89 mm

Learnt synchronizer position gear 5: 8.21 mm

Learnt synchronizer position gear 6: 1.11 mm

Friction coefficient 1: 699

Friction coefficient 2: 699

Friction coefficient 3: 699

General friction coefficient: 695

Gate width gear 1: 11.10 mm

Gate width gear 2: -86.35 mm

Gate width gear 3: -70.82 mm

Gate width gear 4: 265.12 mm

Gate width gear 5: 136.88 mm

Gate width gear 6: 54.79 mm

Gate width gear R: -71.45 mm

Clutch fluid filling

Clutch fluid air bleeding

Static mode learning

Dynamic mode learning

Shift motor calibration

Engage gear test

Clutch actuator full stroke operation test

Gear box self test