Bil, PEUGEOT, EXPERT 3, 9HH - EDC17C10 BR2

PSA reference: 96 61 64 21 80

ECU manufacturer: Siemens

Additional number: 96 79 04 92 80

Softwareversion: 01 15

Software reference: 79 17 53

U1213: Intersystems CAN. One of parameters present in a datastream sent by ABS/ESP is invalid

P0401: Air circuit. Quantity of cold air greater than the setting (after Sales)

Clear DTC

Camshaft and crankshaft synchronization: Ja

Status of last learning of EGR valve: Done

Last turbo initialisation: Done

Initialised initial position of EGR valve lower limit: 19 %

Motor Hastighed: 447.2 Omdr.

Fuel flow regulator: 70 %

Target fuel pressure: 175 bar

Fuel pressure measured: 16 bar

Calculated injected flow: 11.4 mg/impulse

Injector 1 correction value: -46.7 mg/impulse

Injector 2 correction value: -30.7 mg/impulse

Injector 3 correction value: -32.5 mm³/stk

Injector 4 correction value: -36.5 mm³/stk

Brændstoftemperaturføler: 85 °C

Injector opening correction strategies activation status: Aktiv

Injection time cylinder 1: 0.5 ms

Injection time cylinder 2: 2.5 ms

Injection time cylinder 3: 13.1 ms

Injection time cylinder 4: 28.1 ms

High pressure fuel pump: 2451.0 mA

Fuel rail pressure reference value: No limitation

Air flow sensor: 75 °C

Intake air temperature sensor: 52 °C

Turbocharging pressure reference value: 200 mbar

Measured turbo pressure: 2783 mbar

Barometrisk tryk føler: 1925 mbar

Turbo position repeat: 44 %

Køretøjets hastighed sensor: 5 km/h

Status for fartpilotsystem: Aktiv

Clutch pedal: Nedtrykket

Hastighedsbegrænser: Inaktiv

Main brake information: Nedtrykket

Brake pedal redundant: Nedtrykket

Accelerator pedal point of resistance sensor: Not exceeded

Speeder pedal positions føler N1: 400 mV

Speeder pedal position N2: 175 mV

Accelerator pedal position sensor: 10 %

Gear transmission ratio: Parking

Gearbox type: Manuelt

Cruise control speed setting: 120 km/h

Speed limiter speed setting: 120 km/h

Generator: 500 ms

Batteri spænding: 13.60 V

Motor kølevæske temperatur føler: 83 °C

Cooling fan reference speed: 32 %

Køleventilatorhastighed: 175 %

A/C circuit pressure: 2.6 bar

Oil pressure: Utilstrækkeligt

Oil level: 202 mV

Motor status: Driven starting

Cylinder 1 injector code: F7 7F 9B D0

Cylinder 2 injector code: 01 F0 E0 28

Cylinder 3 injector code: 0E 01 C2 18

Cylinder 4 injector code: 0E 23 00 48

Locking of the ECU: Låst

Statspærrestatus: Matched ECU

Problem detected when transmitting the unlock code: The programming status of the engine immobiliser cannot be read

Cooling fan high speed

Cooling fan low speed

Fuel flow regulator

EGR-ventil

Power supply relay

Pre-post heating relay control

Additional heating

Additive pump

Cylinder head replacement

EGR exchanger replacement

EGR valve change

High Pressure pump replacement

Injectors replacement