Bil, PEUGEOT, 407, 5FS - MEV17.4.2 CAN

PSA reference: 96 63 19 37 80

ECU manufacturer: Bosch

Additional number: 96 66 93 42 80

Softwareversion: 15 85

Software reference: 67 31 40

P2177: Mixture regulation fault mixture too lean

Clear DTC

Motor Hastighed: 0

Batteri spænding: 12.00 V

Motor kølevæske temperatur føler: 0.0 °C

Injection time cylinder 1: 0.0 ms

Injection time cylinder 2: 0.0 ms

Injection time cylinder 3: 0.0 ms

Injection time cylinder 4: 0.0 ms

Upstream richness: 0.8 mixture

O2 sensor 1, bank 2 loop control: Lukket sløjfe

Lambda sonde / O2 sensor 1, bank 1: 1.4880 V

Lambda sonde / O2 sensor 2, bank 1: Fed

O2 sensor 2, bank 1 loop control: Åben sløjfe

Lambda sonde / O2 sensor 2, bank 1: 0.4608 V

O2 sensor 1 heater duty cycle: 0.0 %

O2 sensor 2 heater duty cycle: 0.0 %

Upstream mixture correction factor: -0.0 %

Downstream mixture correction factor: -0.0 %

Canister load estimation: 8 %

Richness reference: 1.000 mixture

Canister electrovalve duty cycle: 10 %

Optimum ignition angle: 25.0 °

Maximum ignition angle: 27.0 °

Minimum ignition angle: -13.0 °

Ignition angle cylinder 1: -1 °

Ignition angle cylinder 2: -1 °

Ignition angle cylinder 3: -1 °

Ignition angle cylinder 4: -1 °

Knock retard angle cylinder 4: 7 °

Knock retard angle cylinder 3: 0 °

Knock retard angle cylinder 2: 0 °

Knock retard angle cylinder 1: 0 °

Advance on base reference: 7 °

Outside air temperature: 13 °C

Reference air quantity corrected: 54 %

Measured air quantity corrected: 99 %

Unprocessed reference air quantity: 83.3 %

Unprocessed measured air quantity: 0.8 %

Luft masse måler: 1.5 kg/h

Reference relative pressure in the manifold: 50.0 mbar

Measured relative pressure in the manifold: 1000.0 mbar

Throttle position sensor reference value: 80 °

Throttle position sensor measured value: 12 °

Throttle position sensor voltage copy 1: 1.010 V

Throttle position sensor voltage copy 2: 3.980 V

Inlet camshaft dephaser position reference value: 59 °

Inlet camshaft dephaser position measurement: 59 °

Inlet camshaft dephaser electrovalve duty cycle: 0 %

Inlet camshaft dephaser: Not dephased

Exhaust camshaft dephaser: Not dephased

Target mass air flow: 13.4 kg/h

Modelled intake air pressure: 970 mbar

Inlet air pressure regulator: Ikke aktiv

Correction factor for the inlet pressure: 1.0

Air quantity regulator: Ikke aktiv

Correction factor for the air quantity: 1.0

Exhaust camshaft dephaser position reference value: 122.0 °

Exhaust camshaft dephaser position measurement: 119.0 °

Exhaust camshaft dephaser solenoid valve duty cycle: 6 %

Throttle control duty cycle: 99 %

Direction of control of the throttle: Åbner

Intake air temperature sensor: 0 °C

Motorolietemperaturføler: 130.0 °C

Barometrisk tryk føler: 1000 mbar

Accelerator pedal min position learning 1: 8.3 mV

Accelerator pedal min position learning 2: 8.5 mV

Learning of the accelerator pedal max position 1: 72.6 mV

Learning of the accelerator pedal max position 2: 72.3 mV

Operating zones initialised: 100 %

Adaptation of crankshaft target under deceleration: Done

Friction torque adaptive values in relation to the coolant temperature: 1.6 %

Programming throttle limits: Done

Need for throttle limits learning: Nej

Learning limp home position 1: 1.015 V

Learning limp home position 2: 3.980 V

Learning of throttle minimum limit position 1: 0.527 V

Learning of throttle minimum limit position 2: 4.453 V

Indicated engine torque adaptive values: 1 %

Mixture at idle adaptive values: -0.0 %

Transitory mixture adaptive values: -0.0 %

Downstream sensor mixture adaptive values: -0.0 %

Knock adaption cylinder 4: 0 °

Knock adaption cylinder 3: 0 °

Knock adaption cylinder 2: 0 °

Knock adaption cylinder 1: 0 °

Inlet camshaft dephaser: Ikke programmeret

Value for initialising the lower limit of the inlet camshaft dephaser: 153 °

Exhaust camshaft dephaser: Ikke programmeret

Value for initialising the upper limit of the exhaust camshaft dephaser: 53 °

First programming of the inlet camshaft dephaser: Programmeret

First programming of the exhaust camshaft dephaser: Programmeret

Engine torque obtained by managing ignition angle (setting): 12

Engine torque obtained by managing air flow (setting): 12

Engine torque obtained by managing ignition angle (actual): 0

Engine torque obtained by managing air flow (actual): 0 %

Estimated resistive torque: 21 %

Driver requirement torque: 0 %

Variable valve lift motor duty cycle: 5

Variable valve lift motor supply: Controlled

Variable valve lift motor supply: 12.40 V

Measured valve lift: 9.530 mm

Valve lift reference value: 9.560

Learning angular position corresponding to the min lift of the valves: 0.000 °

Learning angular position corresponding to the max lift of the valves: 0.000 °

Valve stops programming status: Done

Valve stop programming required: Nej

Motorfunktions-status: Normal operation

Control direction of the variable valve lifting motor: Åbner

Current consumed by the variable valve lift motor during programming: 0 A

Current consumed by the variable valve lift motor: 0.0 A

Filling error: 2.0

Temperature variable valve lift motor: 0 °C

Status initial programming low and high valve stops: Cancellation of the programming due to the engine conditions

Required engine speed: 1150 Omdr.

Køretøjets hastighed sensor: 0 km/h

Speeder pedal positions føler N1: 0.390 V

Speeder pedal position N2: 0.200 V

Recalculated accelerator position 1: 0.0 %

Recalculated accelerator position 2: 0.0 %

Cruise control reference speed: 255 km/h

Status for fartpilotsystem: Aktiv

Speed limit reference speed: 255 km/h

Vehicle speed limit: Aktiv

Brake pedal switch 1: Udløst

Brake pedal switch 2: Udløst

Clutch position sensor:

Accelerator pedal point of resistance sensor: Crossed

Handbrake:

Gear engaged: P-A/T

Control unit condition: Låst

Motor status: Cut off stalled

Engine operation: Pedal was pressed

ECU wakeup status: Main wake up

Brændstofniveau: 30 L

Engine stopping time: 2217 sek

Coolant temperature at the last engine stop: 1 °C

Controlled thermostat control setting: 0

Engine coolant temperature reference: 62 °C

Control coolant pump actuator: Inaktiv

Cooling fan high speed relay: Inaktiv

Cooling fan low speed relay: Inaktiv

Fan assembly relay: Nej

Estimation of the mechanical power consumed by A/C compressor: 0 W

Compressor power relief reference: A/C compressor cut

Generator progressive charge reference: 12000 ms

Reference voltage: 10.60 V

Temperature controlled generator: 0 °C

Generator current sensor: 0 A

Generator: 0 %

Refrigerant circuit pressure: 2.2 bar

Power supply: 4.990 V

Number ECU reset: 0

Measured oil level: 0.000 V

Measured oil pressure: 1023 mbar

Oil pressure reference: 500 mbar

Oil pump electrovalve control value: 99 %

Power relay: Ikke aktiv

Starter relay control: Ikke aktiv

ECU temperature: 2 °C

Modelled coolant temperature (plausibility): 0 °C

Oil pump operating mode: Regulation

Noise value measured by the knock detector: 0.0000 mV

Knock detection threshold: 0.0000

Locking of the ECU: Ulåst

Statspærrestatus: After-sales status

Problem detected when transmitting the unlock code: No problem

Electronic throttle control (ETC)

Indsprøjtnings dyse 1

Indsprøjtnings dyse 2

Indsprøjtnings dyse 3

Indsprøjtnings dyse 4

Ignition coil 1

Ignition coil 2

Ignition coil 3

Ignition coil 4

Evaporative emission (EVAP) system, canister purge valve

Cooling fan high speed

Cooling fan low speed

Power supply relay

Additional heating relay

Coolant pump

Thermostat test

Variable valve lift procedure

Motor relay: variable valve lift

Oil pumpe

ECU learn reset

Check timing adjustment