Car, OPEL, Meriva, 2007, Z16SE - Multec (H)
Z16SE - Multec (H) - 0
Identification
VIN no: W0L0XCF2523026411
Repair shop code or tester serial number:
Programming date: FF FF FF FF
Hardware number: DEL 0115351289
Part number alpha code: 09364469 EU
Software number: DNZY
Software version: 4
Existing ECU type approval no: D02001
System: Z16SE
Identifier: 15 A5
Vehicle manufacturer specific: P0802A06
DTC
P0340 [0]: Camshaft position sensor - incorrect signal
P0120 [8]: Throttle position sensor (TPS) 1/A-2/B correlation
P1550 [B]: Electronic throttle control (ETC) power management
P1550 [A]: Electronic throttle control (ETC) limited performance
Controls
Clear DTC
Data stream
Cooling fan relay 1: Off
Cooling fan relay 2: Off
Cooling fan relay 3: Off
Ignition status: Off
Power supply relay: Off
Engine oil pressure: Low pressure
Fuel pump relay: Off
Full load enrichment: Active
Throttle position sensor: Full load
Knock control (B1): On
Deceleration fuel cut-off: Active
O2 sensor 1, bank 1 loop control: Open
EGR valve: Off
Evaporative emission (EVAP) system, canister purge valve: Off
Air/Fuel ratio sensor 1, bank 1: Lean
O2 sensor 1, bank 1 heater: Off
Air/Fuel ratio sensor 2, bank 1: Lean
O2 sensor 2, bank 1 heater: Off
Accelerator pedal position at idle position: Not active
Idle speed offset: Not active
Check engine telltale: Off
Service vehicle soon telltale: On
Electronic throttle control (ETC) limp home mode:
A/C relay: Off
A/C information switch: Off
A/C cut-off mode:
P/N switch: R-D-3-2-1 12V
Neutral control: Present
Torque control: Off
Brake pedal switch 2: Off
Clutch pedal switch: Not active
Vehicle speed in cruise control range: Active
Cruise control tip switch: I+O (Set+Off)
Brake pedal switch 1: On
Cruise control: Off
Oil pressure 1: Low pressure
Oil pressure 2: Low pressure
Oil pressure switch: Not active
Battery voltage: 2 V
Engine speed: 8001 rpm
Idle speed offset: 139 rpm
Target idle speed: 1825 rpm
Vehicle speed sensor: 0 km/h
Acceleration sensor: -5 m/s²
Engine coolant temperature sensor: 0.10 V
Engine coolant temperature sensor: 52 °C
Intake air temperature sensor: 3.16 V
Intake air temperature sensor: -20 °C
MAP sensor: 0.18 V
MAP sensor: 35 kPa
Accelerator pedal position sensor 1: -- V
Accelerator pedal position sensor 2: -- V
Calculated accelerator pedal position: -- %
Throttle position sensor 1: -- V
Throttle position sensor 2: -- V
Calculated throttle position: -- %
EGR valve: -- V
EGR valve command: -- %
Evaporative emission (EVAP) system, canister purge valve: -- %
Fuel level sensor: -- V
Fuel level sensor: -- V
Fuel level sensor: -- %
Fuel level sensor: -- L
Ignition dwell time: -- ms
Injection time bank 1: -- ms
Ignition angle: -- °
A/C pressure sensor: -- V
A/C pressure sensor: -- kPa
Torque control request (AT): -- N·m
Requested torque (ESP): -- N·m
Knock retard angle cylinder 1: -- °
Knock retard angle cylinder 2: -- °
Knock retard angle cylinder 3: -- °
Knock retard angle cylinder 4: -- °
Short term fuel trim bank 1: -- %
Misfire: --
Long term fuel trim bank 1: -- %
Oil level: --
Engine oil level status: --
Fuel system switch state: --
Thermostat heater control: -- %
Port deactivation position sensor: -- V
Radiator coolant temperature: -- °C
Radiator coolant temperature: -- V
Oil level: --
Engine oil level status: --
Immobilizer
Immobilizer function programmed: No
BCM: vehicle-ID is programmed: Yes
BCM: status of vehicle-ID: Correct
Instrument: vehicle-ID: Yes
Instrument: status of vehicle-ID: Incorrect
Security wait time: Not active
Actuators test
Controls
Power supply relay
Fuel pump relay
Ignition coil
EGR valve
Port deactivation test
Evaporative emission (EVAP) system, canister purge valve
Electronic throttle control (ETC)
A/C relay
Cooling fan relay 1
Cooling fan relay 2
Cooling fan relay 3
Fuel system switch LED test
Check engine telltale
Service vehicle soon telltale
EGR Control
Evaporative emission (EVAP) system, canister purge valve
Electronic throttle control (ETC)
Injectors
Instantaneous tank content control
Utility
Controls
ECU learn reset
Reset O2 loop block learn map
Adjust idle speed
Configuration
Controls
Edit configuration
Edit CAN configuration