Car, OPEL, Meriva, 2007, Z18XE - Simtec 71

VIN no: W0L0TGF3532053399

Part number alpha code: 55557447

Hardware number: SIE 0116102000

Software number: 6577925108

Software version: 1025

Existing ECU type approval no: S01001

System: Z18XE

Repair shop code or tester serial number: O200035275

Programming date: 20 16 01 29

Identifier: 16 05

Vehicle manufacturer specific: O405101C

Vehicle manufacturer specific: M2Q5102A

Vehicle manufacturer specific: 6577925202

Vehicle manufacturer specific: 1210

P0351 [1]: Ignition coil 1/A - circuit high voltage

Clear DTC

Oil level: Normal

Engine oil level status: Ok

Cooling fan relay 1: Off

Cooling fan relay 2: Off

Cooling fan relay 3: Off

Power supply relay: Off

Fuel pump relay: Off

Normal engine operating temperature: Active

Intake manifold valve 1: Not active

Throttle position sensor: Idle

Knock control (B1): Off

O2 sensor 1, bank 1 loop control: Closed

EGR valve: Off

Evaporative emission (EVAP) system, canister purge valve: Off

Air/Fuel ratio sensor 1, bank 1: Rich

O2 sensor 1, bank 1 heater: On

Air/Fuel ratio sensor 2, bank 1: Rich

O2 sensor 2, bank 1 heater: On

Idle speed offset: Heating

Check engine telltale: Off

Service vehicle soon telltale: Off

Electronic throttle control (ETC) limp home mode: Not active

A/C relay: Off

A/C information switch: Off

A/C cut-off mode: Ok

P/N switch: R-D-3-2-1 12V

Torque control: Not active

Brake pedal switch 2: Off

Clutch pedal switch: On

Vehicle speed in cruise control range: Not active

Cruise control tip switch: Not active

Brake pedal switch 1: Off

Cruise control: Off

Battery voltage: 14.27 V

Engine speed: 0 rpm

Target idle speed: 625 rpm

Vehicle speed sensor: 0 km/h

Acceleration sensor: 0 m/s²

Engine coolant temperature sensor: 1.59 V

Engine coolant temperature sensor: 90 °C

Intake air temperature sensor: 2.75 V

Intake air temperature sensor: 6 °C

Mass air flow sensor: 0.51 V

Mass air flow sensor: 11 kg/h

Accelerator pedal position sensor 1: 0.96 V

Accelerator pedal position sensor 2: 0.47 V

Calculated accelerator pedal position: 0 %

Throttle position sensor 1: 0.63 V

Throttle position sensor 2: 4.39 V

Calculated throttle position: 9 %

EGR valve: 0.00 V

EGR valve command: 13 %

Evaporative emission (EVAP) system, canister purge valve: 2 %

Fuel level sensor: 5.84 V

Ignition dwell time: 2 ms

Injection time bank 1: 3 ms

Ignition angle: 12 °

A/C pressure sensor: 0.61 V

A/C load signal: Active

A/C pressure sensor: 4260 kPa

Knock sensor signal (B1): 0.35 V

Knock retard angle cylinder 1: 0 °

Knock retard angle cylinder 2: 0 °

Knock retard angle cylinder 3: 0 °

Knock retard angle cylinder 4: 0 °

Short term fuel trim bank 1: -0 %

O2 sensor 1, bank 1: 0.784 V

O2 sensor 2, bank 1: 0.745 V

Electronic throttle control (ETC) learn counter: 0

Relative engine load: -50 %

Long term fuel trim (part load): -50 %

Long term fuel trim (full load): -50 %

Immobilizer function programmed: Yes

BCM: vehicle-ID is programmed: No

BCM: status of vehicle-ID: Incorrect

Instrument: vehicle-ID: No

Instrument: status of vehicle-ID: Incorrect

Security wait time: Not active

Fuel pump relay

Ignition coil

EGR valve

Evaporative emission (EVAP) system, canister purge valve

Intake manifold valve 1

Electronic throttle control (ETC)

A/C relay

Cooling fan relay 1

Cooling fan relay 2

Cooling fan relay 3

Cooling fan relay 4

Check engine telltale

Service vehicle soon telltale

Evaporative emission (EVAP) system, canister purge valve

Electronic throttle control (ETC)

EGR Control

Idle rpm control

Injectors

ECU learn reset

Adjust idle speed

Edit configuration

Edit CAN configuration