Car, OPEL, Insignia, 2012, 1.8L (2H0) - E83

Vehicle Identification Number (VIN): W0LGT8EBXA1007787

Body type: Station wagon

Subscriber ID: O100057235

Programming date: 8209

System code: 18

Identifier: 18 05

XML configuration compatibility identifier: 1

XML data file part number: 0

XML data file alpha code:

Previous subscriber ID: *10MDZ7

2nd previous subscriber ID: *10MDZ7

Manufacturer enable counter (MEC): 68

ECU diagnostic address: 11

Detected component: Engine control module

Manufacturer`s traceability number: 86AAYF2110837002

Broadcast code: H8AA

Boot software part number: 12639237

Software module 1 identifier: 12654173

Software module 2 identifier: 55577673

Software module 3 identifier: 55577209

Software module 4 identifier: 55577673

Software module 5 identifier: 55573530

Software module 6 identifier: 55573530

Software module 7 identifier: 55573530

Software module 8 identifier: 55573530

Software module 9 identifier: 55580831

Software module 10 identifier: 55711903

End model part number: 55577619

Base model part number: 55574337

Software part number alpha code: CA

Software module 1 identifier alpha code: AA

Software module 2 identifier alpha code: AA

Software module 3 identifier alpha code: AA

Software module 4 identifier alpha code: AA

Software module 5 identifier alpha code: AA

Software module 6 identifier alpha code: AA

Software module 7 identifier alpha code: BA

Software module 8 identifier alpha code: RA

Software module 9 identifier alpha code: EA

Software module 10 identifier alpha code: EA

End model part number alpha code: 00

Base model part number alpha code: 00

P0121: Throttle position sensor (TPS) 1/A/single - range/performance

P0251: Fuel pressure regulator 1/single - control circuit

P0135: O2 sensor 1, bank 1 heater - range/performance

Clear DTC

Engine load: 0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim: -100 %

Long term fuel trim: -100 %

MAP sensor: -- kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Intake air temperature sensor: -40 °C

Mass air flow sensor: 0.00 g/sec

O2 sensor 1, bank 1: 0.000 V

O2 sensor 2, bank 1: 0.000 V

Engine running time: 00:00:00

EVAP purge solenoid valve command: 0 %

Remaining fuel in tank: 0 %

Warm-ups since DTC cleared: 0 Counts

Distance since DTC cleared: 0 km

Baro: 0 kPa

Calculated catalyst temperature: -40 °C

Control module voltage: 0.00 V

Air/Fuel equivalence ratio command: 0.00

Air/Fuel equivalence ratio command: 0.00 lambda

Ambient air temperature: -40 °C

Idle speed adjustment: 195 rpm

Idle speed correction: 195 rpm

Target throttle position: 0 %

Electronic throttle control (ETC) system forced engine shutdown: No

Reduced engine power: Inactive

Wide open throttle: No

APP sensor 1 and 2: Agree

Electronic throttle control (ETC) motor: Enabled

Throttle position sensors 1 and 2: Agree

Cooling fan relays 2 and 3 command: Off

Cooling fan relay 1 command: Off

A/C request: No

A/C cut-off due to A/C pressure out of range: No

A/C Off for WOT: No

A/C compressor clutch relay command: Off

TCC/Cruise control brake pedal switch: Released

Clutch pedal starter inhibit switch: On

Clutch pedal: No

Reverse position switch: Off

O2 sensor 2, bank 1 heater: Off

O2 sensor 1, bank 1 heater: Off

Engine oil pressure switch: Ok

Change engine oil indicator command: Off

Low engine oil level indicator command: Off

Low engine oil pressure indicator command: Off

Engine oil level switch: Ok

Cold start: No

Engine controls ignition relay command: Off

Ignition accessory signal: Off

Fuel enrichment - hot catalyst: No

Fuel enrichment - hot coolant: Inactive

Power enrichment: Inactive

Fuel pump relay command: Off

Fuel control loop status: Open

Deceleration fuel cut-off: Inactive

Fuel trim learn: Disabled

Throttle position performance test: Ok

MAP performance test 2: Ok

MAP performance test 1: Ok

MAF performance test: Ok

A/C high side pressure sensor: 0.00 V

Engine oil temperature calculated: -40 °C

Fuel level sensor: 0.00 V

Traction control torque request signal: -- %

Crankshaft position active counter: 0 Counts

Crankshaft position resync counter: 0 Counts

Coolant temperature at engine start: -40 °C

Traction control torque delivered signal: -- %

Fuel trim memory cell: 0

Torque management ignition timing retard: 0.0 °

Knock retard: 0 °

Calculated air flow: 0.00 g/sec

Target idle speed: 0 rpm

Total number of misfire: 0 Counts

Misfire historic, cylinder 1: 0 Counts

Misfire historic, cylinder 2: 0 Counts

Misfire historic, cylinder 3: 0 Counts

Misfire historic, cylinder 4: 0 Counts

Current misfire, cylinder 2: 0 Counts

Current misfire, cylinder 1: 0 Counts

Current misfire, cylinder 3: 0 Counts

Current misfire, cylinder 4: 0 Counts

Cycles of misfire data: 0 Counts

Warm-ups without emission malfunctions: 0 Counts

Warm-ups without non-emission malfunctions: 0 Counts

Accelerator pedal position sensors: 0 %

Throttle position: 0 %

Accelerator pedal position sensor 1: 0 %

Accelerator pedal position sensor 2: 0 %

Throttle position sensor 1: 0 %

Throttle position sensor 2: 0 %

Throttle position sensor 2: 0.00 V

Throttle position sensor 1: 0.00 V

Accelerator pedal position sensor 2: 0.00 V

Accelerator pedal position sensor 1: 0.00 V

Injection time bank 1: 0.00 ms

Total knock retard: 0 °

Mass air flow sensor: 0 Hz

Misfire diagnostic engine speed: 0 rpm

Misfire diagnostic engine load: 0 %

Fuel tank rated capacity: 0 L

Accelerator pedal position: 0 %

Remaining fuel in tank: 0 L

Torque delivered signal: 0 N·m

Catalyst monitor test counter: 0 Counts

MIL control circuit high voltage test status: Malfunction

MIL control circuit low voltage test status: Malfunction

MIL control circuit open test status: Malfunction

Fuel pump relay control circuit high voltage test status: Malfunction

Fuel pump relay control circuit low voltage test status: Malfunction

Fuel pump relay control circuit open test status: Malfunction

A/C compressor clutch relay control circuit high voltage test status: Malfunction

A/C compressor clutch relay control circuit low voltage test status: Malfunction

A/C compressor clutch relay control circuit open test status: Malfunction

Throttle position sensor 1 fully close learn: 0.00 V

Throttle position sensor 2 fully close learn: 0.00 V

Engine off time: 00:00:00

Throttle motor PWM control signal: 0 %

Intake camshaft position actuator solenoid valve control circuit high voltage test status: Malfunction

Intake camshaft position actuator solenoid valve control circuit low voltage test status: Malfunction

Intake camshaft position actuator solenoid valve control circuit open test status: Malfunction

Exhaust camshaft position actuator solenoid valve control circuit high voltage test status: Malfunction

Exhaust camshaft position actuator solenoid valve control circuit low voltage test status: Malfunction

Exhaust camshaft position actuator solenoid valve control circuit open test status: Malfunction

Ignition coil 1 control circuit high voltage test status: Malfunction

Ignition coil 1 control circuit low voltage test status: Malfunction

Ignition coil 1 control circuit open test status: Malfunction

Ignition coil 2 control circuit high voltage test status: Malfunction

Ignition coil 2 control circuit low voltage test status: Malfunction

Ignition coil 2 control circuit open test status: Malfunction

Ignition coil 3 control circuit high voltage test status: Malfunction

Ignition coil 3 control circuit low voltage test status: Malfunction

Ignition coil 3 control circuit open test status: Malfunction

Ignition coil 4 control circuit high voltage test status: Malfunction

Ignition coil 4 control circuit low voltage test status: Malfunction

Ignition coil 4 control circuit open test status: Malfunction

Cylinder 1 injector control circuit high voltage test status: Malfunction

Cylinder 1 injector control circuit low voltage test status: Malfunction

Cylinder 1 injector control circuit open test status: Malfunction

Cylinder 2 injector control circuit high voltage test status: Malfunction

Cylinder 2 injector control circuit low voltage test status: Malfunction

Cylinder 2 injector control circuit open test status: Malfunction

Cylinder 3 injector control circuit high voltage test status: Malfunction

Cylinder 3 injector control circuit low voltage test status: Malfunction

Cylinder 3 injector control circuit open test status: Malfunction

Cylinder 4 injector control circuit high voltage test status: Malfunction

Cylinder 4 injector control circuit low voltage test status: Malfunction

Cylinder 4 injector control circuit open test status: Malfunction

EVAP purge solenoid valve control circuit high voltage test status: Malfunction

EVAP purge solenoid valve control circuit low voltage test status: Malfunction

EVAP purge solenoid valve control circuit open test status: Malfunction

Cooling fan relay 1 control circuit high voltage test status: Malfunction

Cooling fan relay 1 control circuit low voltage test status: Malfunction

Cooling fan relay 1 control circuit open test status: Malfunction

Cooling fan relays 2 and 3 control circuit high voltage test status: Malfunction

Cooling fan relays 2 and 3 control circuit low voltage test status: Malfunction

Cooling fan relays 2 and 3 control circuit open test status: Malfunction

Camshaft position sensor: 0 rpm

Crankshaft position sensor: 0 rpm

O2 sensor 1, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit open test status: Malfunction

O2 sensor 2, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit open test status: Malfunction

5V reference voltage circuit 1: 0.00 V

5V reference voltage circuit 2: 0.00 V

O2 sensor 1, bank 1 heater: 0 %

O2 sensor 1, bank 1 heater: 0.0 A

O2 sensor 2, bank 1 heater: 0.0 A

Engine controls ignition relay control circuit high voltage test status: Malfunction

Engine controls ignition relay control circuit low voltage test status: Malfunction

Engine controls ignition relay control circuit open test status: Malfunction

Engine controls ignition relay feedback signal: 0.00 V

Cruise control: Inactive

A/C disengagement 1st history: None

A/C disengagement 2nd history: None

A/C disengagement 3rd history: None

A/C disengagement 4th history: None

A/C disengagement 5th history: None

A/C disengagement 6th history: None

A/C disengagement 7th history: None

A/C disengagement 8th history: None

A/C high side pressure sensor: 0 kPa

Fuel trim system test state: Disabled

Short term fuel trim test average: -100 %

Long term fuel trim test average: -100 %

Long term fuel trim test average without purge: -100 %

Knocking detected, cylinder 4: No

Knocking detected, cylinder 3: No

Knocking detected, cylinder 2: No

Knocking detected, cylinder 1: No

Injector disabled, cylinder 4 - misfire detected: No

Injector disabled, cylinder 3 - misfire detected: No

Injector disabled, cylinder 2 - misfire detected: No

Injector disabled, cylinder 1 - misfire detected: No

Exhaust camshaft position command: 0 %

Intake camshaft position command: 0 %

O2 sensor 2, bank 1 heater: 0 %

Exhaust camshaft position: 0 °

Intake camshaft position: 0 °

Exhaust camshaft target position: 0 °

Intake camshaft position target: 0 °

Exhaust camshaft position variance: 0 °

Intake camshaft position variance: 0 °

Exhaust camshaft position active counter: 0 Counts

Intake camshaft position active counter: 0 Counts

Output shaft speed sensor: 0 rpm

Distance since last oil level warning: 0 km

Distance since last oil pressure warning: 0 km

MAP sensor: 0.00 V

Intake manifold pressure: 0 kPa

Start-up IAT sensor: -40 °C

Intake manifold tuning (IMT) system, control valve control circuit high voltage test status: Malfunction

Intake manifold tuning (IMT) system, control valve control circuit low voltage test status: Malfunction

Intake manifold tuning (IMT) system, control valve control circuit command: Off

Intake manifold tuning (IMT) system, control valve control circuit open test status: Malfunction

Intake manifold tuning (IMT) system, control valve feedback signal: 0 %

Intake manifold tuning (IMT) system, control valve learn: Inactive

Intake manifold tuning (IMT) system, control valve position:

Clutch pedal position sensor: 0.00 V

Clutch pedal position sensor learned apply position: 0.00 V

Clutch pedal position learn status: Performed successfully

Clutch pedal position sensor learned release position: 0.00 V

Clutch pedal position sensor: 0 %

Service vehicle soon (SVS) indicator command: Off

MIL requested by DTC: No

MIL requested by DTC: No

Check engine telltale: Off

Traction control: --

5V reference voltage circuit 4: Ok

5V reference voltage circuit 3: Ok

5V reference voltage circuit 2: Ok

5V reference voltage circuit 1: Ok

Fuel economy actual: 0.0 L/h

Redundant odometer memory: Not present

5V reference voltage circuit 3: 0.00 V

5V reference voltage circuit 4: 0.00 V

Engine coolant thermostat heater command: 0 %

Engine coolant thermostat heater control circuit high voltage test status: Malfunction

Engine coolant thermostat heater control circuit low voltage test status: Malfunction

Engine coolant thermostat heater control circuit open test status: Malfunction

Radiator coolant temperature sensor: -40 °C

Target engine coolant temperature: -40 °C

Throttle body idle air flow compensation: 0 %

Catalyst monitor test result: No decision

Catalyst monitor not at idle test conditions met: No

Catalyst monitor test state: Inactive

Reduced engine power history: None

RCT vs. IAT sensor temperature at last ECT vs. RCT malfunction detection: Agree

ETC vs. IAT sensor temperature at last ECT vs. RCT malfunction detection: Agree

Power mode: Off

Accelerator pedal position sensor 2 - circuit status: Ok

Accelerator pedal position sensor 1 - circuit status: Ok

Driver requested axle torque: -- N·m

Current gear: Park

Accelerator pedal position sensor 1 learned released position: 0.00 V

Accelerator pedal position sensor 2 learned released position: 0.00 V

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Engine running time: 00:00:00

Control module voltage: 0.00 V

Target throttle position: 0 %

TCC/Cruise control brake pedal switch: Released

Clutch pedal: No

Engine oil level switch: Ok

Starter relay command: Off

Traction control torque request signal: -- %

Traction control torque delivered signal: -- %

Torque management ignition timing retard: 0.0 °

Target idle speed: 0 rpm

Throttle position: 0 %

Cruise control disengagement 1st history: Brake pedal applied

Cruise control disengagement 2nd history: Brake pedal applied

Cruise control disengagement 3rd history: Brake pedal applied

Cruise control disengagement 4th history: Brake pedal applied

Cruise control disengagement 5th history: Brake pedal applied

Cruise control disengagement 6th history: Brake pedal applied

Cruise control disengagement 7th history: Brake pedal applied

Cruise control disengagement 8th history: Brake pedal applied

Accelerator pedal position: 0 %

Torque delivered signal: 0 N·m

Cruise control "On"/"Off" switch: Off

Cruise control "Coast" switch: Active

Cruise control "Set/Coast" switch: Off

Cruise control "Resume/Accelerate" switch: Off

Cruise control: Inactive

Cruise control switch: Active

Traction control: --

Cruise control inhibit reason: Brake pedal applied

Driver requested axle torque: -- N·m

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Engine running time: 00:00:00

Control module voltage: 0.00 V

TCC/Cruise control brake pedal switch: Released

Clutch pedal starter inhibit switch: On

Engine oil pressure switch: Ok

Starter relay command: Off

Engine controls ignition relay command: Off

Ignition accessory signal: Off

Crank request signal: No

Generator F terminal signal: 0 %

Accelerator pedal position: 0 %

Starter relay control circuit high voltage test status: Malfunction

Starter relay control circuit low voltage test status: Malfunction

Starter relay control circuit open test status: Malfunction

Generator L - terminal command: 0 %

Engine controls ignition relay control circuit high voltage test status: Malfunction

Engine controls ignition relay control circuit low voltage test status: Malfunction

Engine controls ignition relay control circuit open test status: Malfunction

Engine controls ignition relay feedback signal: 0.00 V

Generator L-terminal circuit high voltage test status: Malfunction

Generator L-terminal circuit low voltage test status: Malfunction

Generator L - terminal command: Off

Generator L-terminal circuit open test status: Malfunction

ECM response source: Ignition switch start

ECM authentication status: Unknown

ECM challenge status: Invalid

Immobilizer security information programmed: No

Immobilizer system status: Standby

Immobilizer password learn : Inactive

Immobilizer security code accepted: No

Immobilizer security code programmed: No

Immobilizer security code lockout: Inactive

Immobilizer password learn scan tool delay: Inactive

Immobilizer auto learn counter: 0

Immobilizer automatic learn timer: 0 sec

MIL requested by DTC: No

Immobilizer valid response received time: 0 ms

Power mode: Off

Immobilizer security code lockout active timer: 0 ms

Immobilizer security code programming counter: 0 Counts

Immobilizer security code reset counter: 0 Counts

VIN programing counter: 0

Engine load: 0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim: -100 %

Long term fuel trim: -100 %

MAP sensor: -- kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Intake air temperature sensor: -40 °C

Mass air flow sensor: 0.00 g/sec

O2 sensor 1, bank 1: 0.000 V

O2 sensor 2, bank 1: 0.000 V

Engine running time: 00:00:00

EVAP purge solenoid valve command: 0 %

Remaining fuel in tank: 0 %

Warm-ups since DTC cleared: 0 Counts

Distance since DTC cleared: 0 km

Baro: 0 kPa

Calculated catalyst temperature: -40 °C

Control module voltage: 0.00 V

Air/Fuel equivalence ratio command: 0.00 lambda

Air/Fuel equivalence ratio command: 0.00

Ambient air temperature: -40 °C

Target throttle position: 0 %

A/C request: No

A/C cut-off due to A/C pressure out of range: No

A/C Off for WOT: No

TCC/Cruise control brake pedal switch: Released

Clutch pedal starter inhibit switch: On

Clutch pedal: No

Reverse position switch: Off

O2 sensor 2, bank 1 heater: Off

O2 sensor 1, bank 1 heater: Off

Engine oil pressure switch: Ok

Change engine oil indicator command: Off

Low engine oil level indicator command: Off

Low engine oil pressure indicator command: Off

Engine oil level switch: Ok

Cold start: No

Ignition accessory signal: Off

Crank request signal: No

Fuel enrichment - hot catalyst: No

Fuel enrichment - hot coolant: Inactive

Power enrichment: Inactive

Fuel control loop status: Open

Deceleration fuel cut-off: Inactive

Fuel trim learn: Disabled

Coolant temperature at engine start: -40 °C

Fuel trim memory cell: 0

Target idle speed: 0 rpm

Distance since first malfunction: 0 km

Distance since last malfunction: 0 km

Ignition cycles with malfunction since 1st malfunction: 0 Counts

Ignition cycles without malfunction since last malfunction: 0 Counts

Ignition cycles without completed test since 1st malfunction: 0 Counts

Accelerator pedal position sensors: 0 %

Throttle position: 0 %

Injection time bank 1: 0.00 ms

Total knock retard: 0 °

Accelerator pedal position: 0 %

Remaining fuel in tank: 0 L

Torque delivered signal: 0 N·m

Engine off time: 00:00:00

Camshaft position sensor: 0 rpm

Crankshaft position sensor: 0 rpm

O2 sensor 1, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit open test status: Malfunction

O2 sensor 2, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit open test status: Malfunction

5V reference voltage circuit 1: 0.00 V

5V reference voltage circuit 2: 0.00 V

Cruise control "On"/"Off" switch: Off

Cruise control "Set/Coast" switch: Off

Cruise control "Resume/Accelerate" switch: Off

Cruise control: Inactive

Knocking detected, cylinder 4: No

Knocking detected, cylinder 3: No

Knocking detected, cylinder 2: No

Knocking detected, cylinder 1: No

Exhaust camshaft position: 0 °

Intake camshaft position: 0 °

Exhaust camshaft target position: 0 °

Intake camshaft position target: 0 °

Output shaft speed sensor: 0 rpm

Start-up IAT sensor: -40 °C

Clutch pedal position sensor: 0 %

5V reference voltage circuit 3: 0.00 V

5V reference voltage circuit 4: 0.00 V

Radiator coolant temperature sensor: -40 °C

Power mode: Off

Current gear: Park

Distance this driving cycle: 0 km

Engine coolant temperature sensor: -40 °C

Vehicle speed sensor: 0 km/h

Intake air temperature sensor: -40 °C

Engine running time: 00:00:00

Remaining fuel in tank: 0 %

Baro: 0 kPa

Misfire monitor enabled this ignition cycle: No

Misfire monitor complete this ignition cycle: Yes

Fuel system monitor enabled this ignition cycle: No

Fuel system monitor complete this ignition cycle: Yes

Component monitor enabled this ignition cycle: No

Component monitor complete this ignition cycle: Yes

Catalyst monitor enabled this ignition cycle: --

O2S/HO2S monitor enabled this ignition cycle: --

EVAP monitor enabled this ignition cycle: --

HO2S heater monitor enabled this ignition cycle: --

EGR/Camshaft position monitor enabled this ignition cycle: --

Catalyst monitor complete this ignition cycle: --

O2S/HO2S monitor complete this ignition cycle: --

EVAP monitor complete this ignition cycle: --

HO2S heater monitor complete this ignition cycle: --

EGR/Camshaft position monitor complete this ignition cycle: --

Control module voltage: 0.00 V

Ambient air temperature: -40 °C

TCC/Cruise control brake pedal switch: Released

Clutch pedal: No

Cold start: No

Coolant temperature at engine start: -40 °C

Remaining fuel in tank: 0 L

Engine off time: 00:00:00

Start-up IAT sensor: -40 °C

MIL requested by DTC: No

Check engine telltale: Off

Check engine telltale request: No

Number of DTC: 0 Counts

Misfire monitor enabled: No

Misfire monitor complete: Yes

Fuel system monitor enabled: No

Fuel system monitor complete: Yes

Component monitor enabled: No

Component monitor complete: Yes

Catalyst monitor enabled: --

O2S/HO2S monitor enabled: --

EVAP monitor enabled: --

HO2S heater monitor enabled: --

EGR/Camshaft position monitor enabled: --

Catalyst monitor complete: --

O2S/HO2S monitor complete: --

EVAP monitor complete: --

HO2S heater monitor complete: --

EGR/Camshaft position monitor complete: --

Maximum engine speed when engine overspeed detected: 0 rpm

Engine speed when engine overspeed detected: 0 rpm

Vehicle speed when engine overspeed detected: 0 km/h

Accelerator pedal position when engine overspeed detected: 0 %

Engine oil temperature when engine overspeed detected: -40 °C

Current gear when engine overspeed detected: 1

MAF when engine overspeed detected: 0.00 g/sec

Odometer when engine overspeed detected: 0 km

Engine overspeed counter: 0 Counts

Engine overspeed: Not present

Total engine overspeed time: 0 ms

A/C compressor clutch relay

Intake camshaft position actuator

Exhaust camshaft position actuator

Intake camshaft position actuator solenoid valve

Exhaust camshaft position actuator solenoid valve

Cooling fan relay 1

Cooling fan relays 1, 2 and 3

Cooling fan relays 2 and 3

Engine coolant thermostat heater

Engine controls ignition relay

Engine speed

Throttle position

Evaporative emission (EVAP) system, canister purge valve

Fuel control loop status

Cylinder power balance

Fuel pump relay

Fuel trim enable

Generator L terminal

Idle ignition timing

Ignition timing retard

Check engine telltale

Intake manifold tuning (IMT) system, valve control

O2 sensor 1, bank 1 heater

O2 sensor 2, bank 1 heater

Clutch pedal position learning

Crankshaft position variation learn

Adjust idle speed

Reset oil life

Fuel trim reset

O2 sensor 1 heater resistance learned values reset

Throttle body idle air flow compensation reset