Car, MERCEDES, Sprinter 907, 907.155, Transmission control (VGS)

Diagnostic version: 00 09 A5

Boot software number: 0.0.0

Hardware version: 0.0.0

Software version: --

Software version 1: --

Software version 2: --

Supplier: --

Hardware part number:

Software part number (customer): --

Software part number (code): --

Software part number (data): --

Serial number: --

VIN no:

VIN stored:

U140A00: Right front wheel speed sensor - signal is implausible

Clear DTC

Ignition cycle counter: 0

General denominator (IUMPR): 0

Torque converter slip speed: 354.0 rpm

Speed difference (target): 0.00 rpm

Target pressure Kueb: 0.00 mbar

Torque converter lock-up clutch status: Slipping

Position of selection range valve: Initialization value

Transmission mode: Sport

Calculated gear: Neutral position

Parking position: P

Target gear: Gear change abort

Engine torque: 2066.0 N·m

Converted moment: 0.0 N·m

Output speed: 5411.00 rpm

Function mode: No

Steering wheel shift button 'MINUS': Actuated

Steering wheel shift button 'PLUS': Not actuated

Oil pressure sensor of wet clutch: Off

Start enable: Not active

Offroad: Not active

Kickdown: Not active

Emergency operation mode: No

Current error codes: No

Internal transmission speed: 0.00 rpm

Transmission output speed: 0.00 rpm

Turbine speed: 0.00 rpm

Engine speed: 0.00 rpm

Left front wheel speed sensor: 0.00 rpm

Right front wheel speed sensor: 0.00 rpm

Left rear wheel speed sensor: 0.00 rpm

Right rear wheel speed sensor: 0.00 rpm

Rear speed: 0.00 km/h

Front speed: 0.00 km/h

Accelerator pedal position sensor: 0

STEIGUNG: 0

Front speed: 0.00 km/h

Target pressure K1: 0.00 mbar

Target pressure B1: 0.00 mbar

Target pressure B3: 0.00 mbar

Target pressure K3: 0.00 mbar

Target pressure K2: 0.00 mbar

Target pressure B2/BR: 0.00 mbar

Target working pressure: 0.00 mbar

Target pressure KÜB/NAK: 0.00 mbar

Switching valve PnP (target): 0

Switching valve R-D (target): 0

Engine cooling water temperature: 0

Speed: 0.00 rpm

Phase current: 0.00 A

Counter for supported valves: 0

Status Ventil 0 (KUEB): Defective

Current value Ventil 0 (KUEB): 0.00 mA

Status Ventil 1 (B08): Defective

Current value Ventil 1 (B08): 0.00 mA

Status Ventil 2 (K81): Defective

Current value Ventil 2 (K81): 0.00 mA

Status Ventil 3 (K38): Defective

Current value Ventil 3 (K38): 0.00 mA

Status Ventil 4 (B05): Defective

Current value Ventil 4 (B05): 0.00 mA

Status Ventil 5 (K27): Defective

Current value Ventil 5 (K27): 0.00 mA

Status Ventil 6 (B06): Defective

Current Ventil 6 (B06): 0.00 mA

Status Ventil 7 (AD): Defective

Current Ventil 7 (AD): 0.00 mA

Status PnP: Defective

Current value PnP: 0.00 mA

Status lift magnet: Defective

Current lift magnet: 0.00 mA

Battery voltage: 0.00 mV

AUX supply voltage: 0.00 mV

CPU supply voltage: 0.00 mV

1V Sensor supply voltage: 0.00 mV

2V Sensor supply voltage: 0.00 mV

3V Sensor supply voltage: 0.00 mV

4V Sensor supply voltage: 0.00 mV

Park lock sensor PWM raw signal value: 0.00 %

Park lock sensor position: 0.00 mm

Clutch sensor PWM raw signal value: 0.00 %

Clutch position sensor: 0.00 mm

Status K38 sensor: Defective

Working pressure sensor: 0.00 mbar

Status NAK sensor: Defective

Pressure sensor NAK value: 0.00 mbar

Chip temperature sensor: 0.0 °C

Chip temperature sensor 2: 0.0 °C

Operating mode:

Resetting the adaptation values of shift operations

Resetting of adaptation data (Torque converter lockup clutch)

Resetting of learned values of park pawl

Adaptation procedure for torque converter lockup clutch

Teach-in of position sensor of park pawl

Valve flushing

Switch off incline recognition for dynamometer mode

Edit configuration

Edit configuration 2

Edit configuration 3

Edit configuration 4