PKW, MERCEDES, SMART 450, 450.All, M160 - MEG (ME)
M160 - MEG (ME) - 0
Identifikation
Herstellungsdatum: 23 01 01
Hardwarenummer: 30.00
Softwarenummer: 02.01
Diagnoseversion: 0.20
MB Hardwarenummer: 00 70 00 31 07
Lieferant: Bosch
Identifikator: 00 14
FIN: WDC1648861A276478
Fehlercode
P2002: Geber für Kühlmitteltemperatur
Controls
Fehlercode löschen
Ist-Werte
Batteriespannung: 12.61 V
Geber für Ansauglufttemperatur: 215.00 °C
Geber für Kühlmitteltemperatur: 88.00 °C
Geber für Saugrohr-Absolutdruck (MAP): 1310.72 hPa
Mean value of anti-knock control reference level: 2.50 V
Öldruck-Schalter: EIN
Anlasser: EIN
Zündung: EIN
Coding of air conditioning 1: 0
Coding of air conditioning 2: 0
Gebläse: EIN
Motordrehzahl: 4096 UpM
Verdampfertemperatur: 14.67 °C
Lambdasonde 1, Bank 1: 0.31 V
Target O2 sensor 1, bank 1 heater: EIN
Kraftstoffpumpenrelais: AUS
Relais für Anlasser: AUS
Lüfter: AUS
Charge air fan motor: AUS
Lambda correction factor: 1.061
Selbstanpassung im Leerlaufbereich: -54.614 ms
Selbstanpassung im unteren Teillastbereich: 1.031
Selbstanpassung im oberen Teillastbereich: 1.020
Lambda-Regelung: Inaktiv
Sonde 1, Bank 1 Heizstromkreis: AUS
Tankfüllstand: Leer
Supercharger control relay: 18.75 %
Luftmassenmesser: 192.00 kg/h
Accelerator pedal position load signal: 38 %
Drosselklappenpotentiometer: 15.17 °
Lower stop teach-in process: Erfolglos
End of lower stop teach-in process: Nein
Enable lower stop teach-in process: Not approved
Teach-in status of lower stop: Inaktiv
Disable lower stop teach-in process: Ja
Lower stop learned value: Nicht gespeichert
Lower spring check: Nicht erfolgt
Lower stop memory: Data written to EEPROM
Einspritzzeit, Bank 1: 32.77 ms
Zündwinkel: -24.00 °
Injection post-start factor: 48.00
Correction factor of injection time: 48.00
Ignition angle correction for catalytic converter warm-up: 36.00 °
Post-start ignition angle: 36.00 °
Motor-Solldrehzahl: 12288 UpM
Motorlast: 36 %
Signal für Motormoment: 24 N·m
Engine braking torque: 24.00 N·m
Schubabschaltung: AUS
Leerlaufdrehzahl: Nein
Start enable transmission: Ja
Start enable clutch: Ja
Immobilizer deactivated: Ja
Motor-Betriebszustand: Catalytic converter not heated
Motor-Betriebszustand: No post-start enrichment
Motor-Betriebszustand: No full-load enrichment
Motor-Betriebszustand: End of starting procedure
CAN message 'Brake signal': Brake is not operated
Bremslichtschalter: Brake is not operated
Shift lever signal 1: 0
Shift lever signal 2: 1
Shift lever signal 3: 0
Shift lever signal 4: 1
Temperatur bei Motorstart: 40 °C
Bremse: Not operated
Kühlgebläse: AUS
Charge air fan motor: AUS
Klimaanlage: AUS
Elektrischer Sauglüfter: AUS
Tankentlüftungssteuerung: AUS
Sonde 1, Bank 1 Heizstromkreis: Inaktiv
Average knock retard angle: 12.00 °
Klopfzündwinkel, Zylinder 1: 36.00 °
Klopfzündwinkel, Zylinder 2: 12.00 °
Klopfzündwinkel, Zylinder 3: 36.00 °
Lambdasonde 2, Bank 1: 0.313 V
Lambdasonde 2, Bank 1, Durchschnittswert : 0.062
Calculated catalytic converter temperature: 76 °C
Cylinder reference value for irregular engine running: 0.00 (umdr/sec)²
Cylinder test value for irregular engine running: 480 m
Cylinder test value 1 for irregular engine running: 21.83 (umdr/sec)²
Cylinder test value 2 for irregular engine running: 21.83 (umdr/sec)²
Cylinder test value 3 for irregular engine running: 21.83 (umdr/sec)²
Raddrehzahlsensor vorn links: 6144 UpM
Raddrehzahlsensor vorne rechts: 6144 UpM
Raddrehzahlsensor hinten links: 6144 UpM
Raddrehzahlsensor hinten rechts: 6144 UpM
Speed of non-driven axle: 2328.13 km/h
Speed of driven axle: 256.00 km/h
Speed of automatic transmission: 256.00 km/h
Drehzahl Getriebeeingangswelle: 12288 UpM
Sollgang: Nullstellung
Engaged gear in transmission software: Nullstellung
Value of incremental sensor 'Transmission': 33138
Gear position sensor: 45601
Getriebetemperatur: 8.00 °C
Transmission current: 51.34 A
Specified current: 38.570 A
Turning angle sensor (raw value): 12288
Transmission current (raw value): 4096
Resulting throttle valve specified position: 50.55 °
Status Kupplung: Not set
Gear motor on/of ratio: 12288.00
Transmission state at engine intervention: 48
Gear is on neutral position: Nein
CAN message 'Brake signal': Not operated
Bremslichtschalter: Not operated
Overcurrent cutout: AUS
Start enable from clutch and transmission: Nein
Enable 'Shift request recognition': Nein
Enable 'Gear recognition': Nein
Enable 'Transmission logic': Nein
Transmission run-on: AUS
Request 'Clutch operation': Nein
Transmission blockage: Nein
Shift position request: Nein
Status Kupplung: Engine OFF with vehicle at standstill
Actual clutch position: 37507
Specified clutch position: 4096
Slipping point of clutch: 82 %
Wählhebel-Stellung: 48 %
Coupling motor: 38 %
Clutch protection class: Normalmodus
Engaged gear in clutch software: Nullstellung
Counter for clutch protection class 1: 62
Counter for clutch protection class 2: 19
Counter for clutch protection class 3: 7
Maximum friction power of clutch: 10890 W
Time in clutch protection class 3: 2 min
Average clutch drag point: 20655
Disengaged position (mechanically taught in): 797
Power loss of clutch: 0
Power loss of clutch: 0
Power loss of clutch: 0
Mileage at clutch installation (High byte): 3145728 km
Mileage at clutch installation (Low byte): 4096 km
Maximum possible clutch drag point: 35000
Program selector switch: Manuell
Fuel flow (0,217ul/250ms): 10.666
Current fuel consumption: 11 L/100km
Average fuel consumption: 16 L/100km
Stellgliedtest
Controls
Anlasser
Charge air fan motor
Wastegate bypass regulator valve
Switch on sensor heater upstream of TWC [KAT]
Drosselklappe
Wastegate bypass valve vacuum cell
Transmission adaptation
Switch on relay Transmission
Engage gear 1
Engage gear 2
Engage gear 3
Engage gear 4
Engage gear 5
Engage gear 6
Rückwärtsgang
Neutral gear
Energize transmission with specified value
Move transmission into specified position
Move clutch into 'OPENED' position
Move clutch into 'CLOSED' position
Perform clutch function test 1
Perform clutch function test 2
Perform clutch function test 3
Dienstprogramme
Controls
VIN ändern
Clutch pulsing
Teach in clutch engaged and disengaged position
Teach-in drag point of clutch
Reading adaptation values
Reset of transmission adaptation data
Reset of clutch adaptation data
Reset of clutch protection class
Reset Adaption Lambdasonde