Car, CHERY, EXEED LX, Climate control (CLM)

Boot software number: FBL-V1.3.1

System identification: 9AK

Vehicle manufacturer ECU hardware number: 0.3.0

Vehicle manufacturer ECU software number: 01.11.00

Vehicle manufacturer spare part number: 301000278AA

ECU serial number: --

Calibration version: --

Vehicle manufacturer logistic software part number: --

Logistics software part number: --

Clear DTC

Internal temperature (left): -3.50 °C

Ambient temperature: -3.50 °C

Evaporator temperature: -4.00 °C

Software configuration code: 55

Solar sensor element left: 365 W/m2

Blower voltage: 12.50 V

Stepper motor: 72 %

Recycling motor control: 73 %

Left air mix flap motor position: 121 %

Right air mix flap motor position: 73 %

Internal temperature (right): -3.50 °C

Solar sensor element right: 345 W/m2

Battery voltage: 12.50 V

AQS sensor PWM duty: 73 %

AQS sensor PWM period: 464.10 Hz

Inside PM2.5 sensor duty: 68 %

Inside PM2.5 sensor period: 7.20 Hz

Outside PM2.5 sensor duty: 72 %

Outside PM2.5 sensor period: 25.50 Hz

Humidity sensor: 255 %

Pressure sensor: 13333.10 hPa

Blower fan output: 72 %

Fragrance motor step: 73 %

ECV negative control: Reserved

ECV PWM duty: 73 %

ECV positive feedback current: 4641 mA

ECV negative feedback current: 8532 mA

PTC relay 1: Off

PTC relay 2: Off

PTC relay 3: Off

Ionizer: Invalid value

Fragrance generator state: Off

A/C status: Not defined

A/C compressor torque: 7.20 N·m

LIN communication: Reserved

Solar sensor element left: 850 W/m2

Solar sensor element right: 1530 W/m2

Electronic expansion valve communication error: --

Electronic expansion valve current initialization status: --

Electronic expansion valve running status: --

Electronic expansion valve faulty status: --

Electronic expansion valve temperature alarm: --

Electronic expansion valve response position: --

Electronic expansion valve voltage status: --

A/C compressor high voltage status: --

A/C compressor safety default (include interlock): --

A/C compressor speed: --

Confirmation of non-safety internal failure: --

Confirmation of a failure preventing from product break: --

DC bus current consumption (LSB): -- A

DC bus current consumption (MSB): -- A

Failure leading to a permanent stop of the product: --

High voltage network failure confirmed: --

Internal fault induce untimely working (other products failures): --

Maximum power reach: --

Sensor failure on high voltage measurement confirmed: --

Current draw of HV-PTC: -- A

Current sensor fault: --

Defect of heater legs indicator: --

External power supply failure: --

High voltage measurement: -- V

HV-PTC status signals: --

HV valid indicator: --

Medium temperature 1 (outlet by default): -- °C

Medium temperature 2 (inlet by default): -- %

LIN communication error: --

LIN response error indicator: --

Over temperature indicator: --

PCB temperature: -- °C

Short circuit detected: --

Temperature sensor faulty: --

Diagnostic configuration: --

Left outlet temperature: -- °C

Right outlet temperature: -- °C

Rear blower: -- V

Rear blower output (PWM duty): -- %

Ambient temperature (raw): -- °C

HVH DC current: -- A

HVH internal water temperature 1: -- °C

HVH internal water temperature 2: -- °C

HVH defect heater circuits: --

HVH HV voltage: -- V

HVH HV voltage valid: --

HVH current sensor fault: --

HVH internal PCB temperature: -- °C

HVH off short current: --

HVH SP external power supply fault: --

HVH SP LIN fault: --

HVH RS error: --

HVH status: --

HVH temperature limit: --

HVH temperature sensor fault: --