Car, CHERY, QQ6, JAGGI (S21FL, S21), Bosch ME7.9.7 (ECM)
Engine - Bosch ME7.9.7 (ECM) - 0
Identification
VIN no: 23456789@ABCDEFGH
Vehicle manufacturer ECU hardware number: 03605010 HA
System supplier ECU hardware number: BOS 01000261B07808
System supplier ECU software number: 005S180823
System supplier ECU software version number: 4626
Type approval number: 3689BCDH
Engine type: I480EJ
Repairshop or tester serial number: 12345678@A
Programming date: 42434445
Calibration repairshop or tester serial number :: 13878
Calibration data version: 23456789
Software calibration number (SCN): @ABCDEFGHI
Vehicle manufacturer specific data: F01R00D634
DTC
P0015: Camshaft position "B" - timing over-retarded bank 1
P1111: Unknown DTC
Controls
Clear DTC
Data stream
Number of DTC: 255
Immobilizer is in initial state: Yes
No freestart counts left: Yes
Challange response without engine author: Yes
Immobilizer failed: Yes
Security grade:
Security code programmed: Programmed
Security code correct entered: Correct
Security code lock up function active: Active
Security code status:
Cooling fan relay 1: On
Cooling fan relay 2: On
Cooling fan PWM: On
Idle speed: Reached
Terminal 15 (ignition): Yes
Power supply relay: Yes
Normal engine operating temperature: Reached
Fuel pump relay: Yes
Vehicle speed pulse: Yes
Starter relay: Yes
Power enrichment: Yes
Throttle position at idle position: Yes
Throttle wide open position: Yes
Deceleration fuel cut-off: Yes
Catalyst protection enrichment B1: On
Lambda control: On
EGR system: On
Evaporative emission (EVAP) system, canister purge valve: On
Deceleration fuel cut-off: On
O2 sensor 1, bank 1 heater: On
O2 sensor 1, bank 1 rich: Yes
O2 sensor 2, bank 1 heater: On
O2 sensor 1, bank 1 lean: Yes
Accelerator pedal position at idle position: Yes
Electrical load 1: Yes
Electrical load 2: Yes
Service vehicle soon telltale: Yes
Check engine telltale: On
Service vehicle soon (SVS) flash: Yes
Check engine telltale flash: On
Service vehicle soon (SVS) fault: Yes
Throttle position unknown or error: Yes
Electronic throttle control (ETC) motor power supply fault: Yes
A/C relay: On
Idle speed up due to A/C on: Yes
A/C request: Yes
A/C cut-off due to full load (no delay): Yes
A/C compressor relay: On
Battery voltage: 9.60 V
Engine speed: 0.0 rpm
Target idle speed without compensation: 850 rpm
Target idle speed with compensation: 850 rpm
Vehicle speed sensor: 0 km/h
Acceleration sensor: 29.4 m/s²
Engine coolant temperature sensor: 1.67 V
Engine coolant temperature sensor: 96 °C
Intake air temperature sensor: 2.67 V
Intake air temperature sensor: 45 °C
Outside air temperature: 96 °C
A/C evaporator temperature sensor: 1.33 V
Intake manifold model air mass flow filtered value: 462.6 kg/h
MAP sensor: 0.35 V
Mass air flow sensor: 2.67 V
Mass air flow sensor: 462.6 kg/h
MAP sensor: 34.7 kg/h
Accelerator pedal position sensor 1: 2.67 V
Accelerator pedal position sensor 2: 2.67 V
Throttle position sensor 1: 2.67 V
Throttle position sensor 2: 2.67 V
Target throttle position: 53.3 %
Throttle position sensor: 53.3 %
Throttle position PWM servo signal: 33.3 %
Injection time bank 1: 13.6 ms
Ignition dwell time: 13.6 ms
Ignition angle: 68.0 °
Fuel consumption: 75.0 L/h
Knock sensor 1: 682.67 V
Knock sensor 2: 597.33 V
Knock retard angle cylinder 1: 102.0 °
Knock retard angle cylinder 2: 102.0 °
Knock retard angle cylinder 3: 102.0 °
Knock retard angle cylinder 4: 102.0 °
Short term fuel trim bank 1: 1.067
O2 sensor 1, bank 1: 2.67 V
O2 sensor 2, bank 1: 2.67 V
Long term fuel trim bank 1: 102.400 %
Mixture adaptive-add: 240.9 %
Engine load: 53.1 %
Idle torque self learn: 107.0 %
Idle torque adaptation: 106.2 %
Canister purge duty cycle: 53.3 %
Relative fuel injection quantity of canister control: -1236.0 %
Canister purge ratio: 0.3 %
Evaporative emission (EVAP) system - canister load: 2380.0
Time since check engine telltale on: 18:12:15
Actuators test
Controls
Check engine telltale
Evaporative emission (EVAP) system, canister purge valve
Fuel pump relay
Cooling fan relay 1
Cooling fan relay 2
A/C relay
Service vehicle soon telltale
Ignition angle
Injectors
Idle rpm control
Utility
Controls
ECU learn reset
ECU Reset
Reset adaptation values