Car, KIA, General, VENGA (YN), 2018, G 1.6 DOHC, G 1.6 DOHC - Engine Control (ENGINE)
G 1.6 DOHC - Engine Control (ENGINE) - 0
Identification
Software version bootloader: 17980021
Software version number: 0000000000
VIN no: --
Calibration ID: GACD-HS66QSC1C00
Supplier ECU software number: ECKT03H7
DTC
Controls
Clear DTC
Data stream
Immobilizer built-in: On
SMART key built-in: On
SMARTRA2 built-in: Off
SMARTRA3 built-in: Off
MAF sensor built-in: Off
Fuel level sensor built-in: Off
Generator PWM built-in: On
Fuel tank pressure sensor built-in: Off
A/C pressure sensor built-in: On
Low pressure fuel pump relay (Normally closed): On
Linear O2 sensor built-in: Off
MAP sensor built-in: On
ESP built-in: On
Adapted cruise control built-in: Off
CDA built-in: Off
Leak test type - Under pressure system: Off
VVL built-in: Off
Battery sensor built-in: On
Check engine telltale: On
Fuel cut-off condition: Off
Ignition switch: On
Fuel pump: Off
Anti-jerk function is active: Off
Power supply relay: On
Torque control request for gear shifting: Off
Variant coding: A/T
WSS signal from ABS: On
Open lock-up clutch: Off
Driving status: Off
Leaded fuel pack: Off
Shift lever position-D(AT Only): Off
Brake pedal switch: Off
Brake lamp switch: Off
Engine operating status - full load: Off
Engine operating status - idle: Off
Engine operating status - part load: Off
Limitation of positive torque gradient active load shockdamping: Off
Condition idle controller active: Off
ETC learning is finished successfully: On
Start over run relay activation: Off
Condition start: Off
Electronic throttle control (ETC) built in: On
Synchronization successed: Off
Fan high: Off
A/C on condition: Off
Fan low: Off
A/C request to ECU (A/C Switch): Off
A/C compressor on: Off
Fan PWM output built-in: Off
Non-AMS system built in: Off
Sensorless AMS system built in: Off
AMS system built-in: On
Canister purge phase: Off
Knocking detected: Off
Knock control: Off
Knock control adaptation is active: Off
Evaporative emission (EVAP) system, canister purge valve: Off
Variable camshaft pack: On
Camshaft control: Off
Intake camshaft position actuator, bank 1: Off
Exhaust camshaft position actuator, bank 1: Off
O2 sensor 1, bank 1 loop control: Off
Lambda control: Off
Permit open-Loop operation by workshop tester: Off
O2 sensor 1, bank 1 heater: Off
O2 sensor 2, bank 1 heater: Off
Power steering pressure switch built-in: Off
Power steering switch: Off
Comprehensive ignition monitoring (Diesel): Off
Cruise control main telltale: Off
Cruise control set telltale: Off
Cruise control "Cancel" switch: On
Cruise control "Resume" switch: Off
VIS 1 operation status: Off
ISG system built-in(ISG): Off
EGR built-in: Off
LPI system built in: Off
Bi-Fuel system built in: Off
Flex fuel system built in (FFV): Off
GDI system built in: Off
FPCM control by EMS ECU: Off
FPCM control by external FPCM ECU: Off
Battery voltage: 11.85 V
Ignition voltage: 11.78 V
Engine speed: 0 rpm
Target idle speed: 1130 rpm
MAP sensor: 3.94 V
MAP sensor: 964.5 hPa
Throttle position sensor 1: 0.771 V
Throttle position sensor: 6.3 %
Engine coolant temperature sensor: 0.90 V
Engine coolant temperature sensor: 10.5 °C
Intake air temperature: 1.70 V
Intake air temperature: 9.8 °C
Engine oil temperature: 10.5 °C
O2 sensor 1, bank 1: 0.45 V
O2 sensor 2, bank 1: 0.45 V
Vehicle speed: 0.0 km/h
Relative air charge: 100.0 %
Evaporative emission (EVAP) system, canister purge valve: 0.0 %
Injection time cylinder 1: 0.00 ms
Injection time cylinder 2: 0.00 ms
Injection time cylinder 3: 0.00 ms
Injection time cylinder 4: 0.00 ms
Altitude correction: 1.0
Barometric pressure sensor: 1005 hPa
Current calculated load value: 0.000 %
Throttle position sensor set point: 1.6 %
Electronic throttle control (ETC) motor duty cycle and direction: -61.868 %
Throttle position adaptation for idle (sensor 1): 0.521 V
Throttle position adaptation for idle (sensor 2): 4.484 V
Throttle position sensor 1: 6.641 %
Throttle position sensor 2: 6.470 %
Throttle position sensor 1: 0.775 V
Throttle position sensor 2: 4.232 V
A/C pressure: 8462 hPa
Filtered electrical raw load on the generator: 12.650 %
Gear engaged in AT vehicle: P,N,R
Torque decrease request from TCU: 3276.7 N·m
Torque increase request from TCU: -3276.8 N·m
Accelerator pedal position sensor 1: 737.8 mV
Accelerator pedal position sensor 2: 361.6 mV
Accelerator pedal position sensor: 0.000 %
Compensated battery voltage: 12.490 V
Battery voltage raw value: 12.488 V
Battery current: -19.2 A
Battery current raw value: 2.12 V
Battery temperature: 58.3 °C
Battery temperature raw value: 1.11 V
State of charge of battery: 50.488 %
Target indicated torque: 0.0 N·m
Indicated actual torque: 0.000 %
Engine torque losses: 11.0 N·m
Air mass adaptation: -1.772 %
Power steering pressure: 69500 hPa
Power steering pressure sensor: 3.07 V
Idle CO adjustment: 0.000 %
Adaptation in idle speed bank 1: 1.688 %
Adaptation in part load bank 1: 0.978
Ignition angle cylinder 1: 0.000 °
Ignition angle cylinder 2: 0.000 °
Ignition angle cylinder 3: 0.000 °
Ignition angle cylinder 4: 0.000 °
Exhaust gas temperature: 155 °C
O2 sensor 1, bank 1 correction: 1.000 %
Target lambda value: 1.000 %
Upper limit for cycle duration of lambda sensor up. Cat.: 2.740 sec
Filtered cycle duration O2 sensor signal up. Catalyst: 1.600 sec
O2 sensor 2, bank 1 correction: -- sec
O2 sensor 2, bank 2 correction: -- sec
Integrator value of O2 sensor downstream catalyst: --
Threshold time for monitoring of catalyst: -- sec
Mean amplitude of sensor signal behind catalyst-Bank 1: --
Mean amplitude of sensor signal behind catalyst-Bank 2: --
Threshold value of catalyst defect: --
Total number of catalyst efficiency monitoring with error results: --
O2 sensor 1, bank 1 heater duty cycle (LSF): -- %
O2 sensor 1, bank 1 heater duty cycle (LSU): -- %
O2 sensor 2, bank 1 heater duty cycle (LSF): -- %
O2 sensor 1, bank 2 heater duty cycle (LSF): -- %
O2 sensor 1, bank 2 heater duty cycle (LSU): -- %
O2 sensor 2, bank 2 heater duty cycle (LSF): -- %
O2 sensor heating period-Upstream catalyst-bank 1(LSF): -- sec
O2 sensor heating period-Upstream catalyst-bank 2(LSF): -- sec
O2 sensor heating period-Downstream catalyst-bank 1(LSF): -- sec
O2 sensor heating period-Downstream catalyst-bank 2(LSF): -- sec
Upper limit for TV correction: -- sec
Lower limit for TV correction: -- sec
O2 sensor heating period-Upstream catalyst-bank1(LSU): -- sec
O2 sensor heating period-Upstream catalyst-bank2(LSU): -- sec
Knock retard angle cylinder 1: 0.000 °
Knock retard angle cylinder 2: 0.000 °
Knock retard angle cylinder 3: 0.000 °
Knock retard angle cylinder 4: 0.000 °
Knock adaption cylinder 1: 0.000 °
Knock adaption cylinder 2: 0.000 °
Knock adaption cylinder 3: 0.000 °
Knock adaption cylinder 4: 0.000 °
Intake camshaft bank 1 actual position: 25.163 °
Intake camshaft bank 1 target position: 25.163 °
Intake camshaft bank 1 position duty cycle: 0.000 %
Exhaust camshaft bank 1 actual position: -16.965 °
Exhaust camshaft bank 1 target position: -16.965 °
Exhaust camshaft bank 1 position duty cycle: 0.000 %
Angle of inlet-camshaft edges relative to crankshaft: 0.0 °
Angle of outlet-camshaft edges relative to crankshaft: 0.0 °
Misfire cycle delay reason: NO_DELAY
Current misfire, cylinder 1: 1 Count
Current misfire, cylinder 2: 16 Count
Current misfire, cylinder 3: 14 Count
Current misfire, cylinder 4: 29 Count
Misfire impairing exhaust emission, cylinder 1: 0 Count
Misfire impairing exhaust emission, cylinder 2: 0 Count
Misfire impairing exhaust emission, cylinder 3: 0 Count
Misfire impairing exhaust emission, cylinder 4: 0 Count
Misfire for catalyst damage, cylinder 1: 0 Count
Misfire for catalyst damage, cylinder 2: 0 Count
Misfire for catalyst damage, cylinder 3: 0 Count
Misfire for catalyst damage, cylinder 4: 0 Count
Total counter of emission relevant misfiring of all cylinders: 0 Count
Total counter of catalyst damaging misfiring of all cylinders: 0 Count
Coolant temperature at engine start: 84.8 °C
Water temperature model: 50.2 °C
Lowpass filtered battery voltage: 12.465 V
Continuous operation time after engine start: 0.0 sec
Operating time: 38994 min
Distance traveled when MIL ON: 0 km
Number of warm-ups since stored confirmed DTC cleared: 255
Number of DTC: 0
Ignition angle cylinder 1: 0.0 °
Ignition angle cylinder 2: 0.0 °
Ignition angle cylinder 3: 0.0 °
Ignition angle cylinder 4: 0.0 °
Air mass adaptation: 1.1 %
A/C pressure sensor: 0.981 V
A/C pressure: 4548.9 hPa
Coolant temperature at engine start: 10.5 °C
Water temperature model: 10.5 °C
Altitude correction: 1.0
Barometric pressure sensor: 995 hPa
Effective injection time: 0.0 ms
Throttle position sensor set point: -- %
Throttle position sensor 1: -- %
Throttle position sensor 2: -- %
Throttle position sensor Angle2-Voltage(5V base): -- V
Electronic throttle control (ETC) motor duty cycle and direction: -- %
Accelerator pedal position sensor: -- mV
Accelerator pedal position: -- %
Engaged gear (AT Vehicle): --
Indicated actual torque: -- %
Target indicated torque: -- %
Torque request from TCU: -- %
Accelerator pedal position sensor-1 Voltage(5V base): -- V
Accelerator pedal position sensor-2 Voltage(5V base): -- V
Throttle position adaptation for idle: -- V
Throttle position sensor Angle1-Voltage(5V base): -- V
Throttle position sensor-1(3.3V base): -- V
Throttle position sensor-2(3.3V base): -- V
Accelerator pedal position sensor-1 Voltage(3.3V Base): -- V
Accelerator pedal position sensor-2 Voltage(3.3V Base): -- V
Fuel tank pressure sensor: -- V
Adaptation in idle speed bank 1: -- %
Adaptation in part load bank 1: -- %
Multiplicative correction of the mixture adaptation due to ethanol: --
Relative fuel injection quantity of canister control: -- %
O2 sensor 1, bank 1 correction: -- %
Target lambda value: --
O2 sensor 2, bank 1 correction: -- sec
Filtered cycle duration O2 sensor signal up. Catalyst: -- sec
O2 sensor 2, bank 1 heater off duration: -- sec
O2 sensor 1, bank 1 heater off duration: -- sec
Target EGR duty cycle: -- %
Fuel level sensor: -- V
LPG gas fuel pressure: -- kPa
Knock retard angle cylinder 1: -- °
Knock retard angle cylinder 2: -- °
Knock retard angle cylinder 3: -- °
Knock retard angle cylinder 4: -- °
Knock adaption cylinder 1: -- °
Knock adaption cylinder 2: -- °
Knock adaption cylinder 3: -- °
Knock adaption cylinder 4: -- °
Intake camshaft bank 1 target position: -- °
Intake camshaft bank 1 actual position: -- °
Intake camshaft bank 1 position duty cycle: -- %
Exhaust camshaft bank 1 target position: -- °
Exhaust camshaft bank 1 actual position: -- °
Exhaust camshaft bank 1 position duty cycle: -- %
Current misfire, cylinder 1: 0 Count
Current misfire, cylinder 2: 0 Count
Current misfire, cylinder 3: 0 Count
Current misfire, cylinder 4: 0 Count
Misfire impairing exhaust emission, cylinder 1: 0 Count
Misfire impairing exhaust emission, cylinder 2: 0 Count
Misfire impairing exhaust emission, cylinder 3: 0 Count
Misfire impairing exhaust emission, cylinder 4: 0 Count
Misfire for catalyst damage, cylinder 1: 0 Count
Misfire for catalyst damage, cylinder 2: 0 Count
Misfire for catalyst damage, cylinder 3: 0 Count
Misfire for catalyst damage, cylinder 4: 0 Count
Total counter of emission relevant misfiring of all cylinders: 0 Count
Total counter of catalyst damaging misfiring of all cylinders: 0 Count
Target generator voltage duty cycle (C-terminal): 59.8 %
Duty cycle from generator PWM signal (FR-terminal): 12.6 %
Integrated battery current for battery refresh mode: 0.0 Ah
SOC low counter for battery refresh mode: 0
Driver start counter for battery refresh mode: 0
Operating timer of battery refresh mode: 0 sec
LPG fuel tank level: -- V
LPG fuel tank level: -- L
LPG fuel tank temperature: -- V
LPG fuel tank temperature: -- °C
LPG fuel rail temperature: -- V
LPG fuel rail temperature: -- °C
LPG pressure in the fuel rail mean value: -- V
LPG pressure in the fuel rail mean value: -- hPa
Pump speed of the LPG electrical fuel pump as PWM signal: -- %
Target fuel flow rate: -- g/sec
Current fuel pump step: --
Percentage of butane in the LPG: -- %
Effective LPG injection time: -- ms
Actual LPG fuel ratio in bi-fuel system: -- %
Actuators test
Controls
Check engine telltale
Immobilizer telltale
Cruise Control Main Lamp(Option)
ISG Lamp
Gasoline Lamp (Bi-Fuel)
Cruise Control SET Lamp(Option)
Over speed indicator(Option)
Oil Change Warning Lamp
FPCM pressure control
A/C compressor relay
Fuel pump relay (1st stage)
Fuel pump control (1st stage)
Fuel pump relay (2nd stage)
Fuel pump control (2nd stage)
High pressure fuel pump control
High pressure fuel pump control 2
Fuel Pump Relay for LPG
Fuel Pump Relay Control for LPG
Cooling fan low speed
Cooling fan high speed
Fan PWM
LPG Fuel Pump PWM
LPG Cut Valve for Fuel Rail
LPG Cut Valve for Fuel Tank
CVVT intake
CVVT exhaust
Intake camshaft oil control valve B1
Exhaust camshaft oil control valve B1
Intake camshaft oil control valve B2
Exhaust camshaft oil control valve B2
Additive Correction for O2 Sensor Heaters B1S1
Additive Correction for O2 Sensor Heaters B2S1
Additive Correction for O2 Sensor Heaters B1S2
Additive Correction for O2 Sensor Heaters B2S2
Additive Correction for all O2 Sensor Heaters
ISA idle speed actuator additive correction
CDA Control Solenoid Valve - IN, B1
CDA Control Solenoid Valve - EX, B1
CDA Control Solenoid Valve - IN, B2
CDA Control Solenoid Valve - EX, B2
VVL Control Solenoid Valve - IN, B1
VVL Control Solenoid Valve - EX, B1
VVL Control Solenoid Valve - IN, B2
VVL Control Solenoid Valve - EX, B2
Turbo waste gate (WGT) valve
Turbo dump (ReCirculation) valve (RCV)
LPG injector disable cylinder 1
LPG injector disable cylinder 2
LPG injector disable cylinder 3
LPG injector disable cylinder 4
Bi-fuel system fuel change (GSL to LPG)
Bi-fuel system fuel change (LPG to GSL)
Injector 1
Injector 2
Injector 3
Injector 4
Injector 5
Injector 6
Injector 7
Injector 8
Ignition coil 1
Ignition coil 2
Ignition coil 3
Ignition coil 4
Ignition coil 5
Ignition coil 6
Ignition coil 7
Ignition coil 8
Utility
Controls
Resetting adaptive values
Edit VIN
ISG test (Option)