Car, HOLDEN, Captiva, 2017, 2.4L (LE9) - 2.4L (LE9)

VIN no: W0LGT8EBXA1007787

Software module 1 identifier: 12654173

Software module 2 identifier: 55577673

Software module 3 - identifier: 55577209

Software module 4 - identifier: 55577673

Software module 5 - identifier: 55573530

Software module 6 - identifier: 55573530

Software module 7 - identifier: 55573530

Software module 8 - identifier: 55573530

Software module 10 - identifier: --

End model part number: 55577619

Base model part number: 55574337

Clear DTC

Engine load: 0.0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim: -100 %

Long term fuel trim: -100 %

Fuel pressure sensor: 0 kPa

MAP sensor: 0.0 kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Intake air temperature sensor: -40 °C

Mass air flow sensor: 0.00 g/sec

O2 sensor 1, bank 1: 0.000 V

O2 sensor 2, bank 1: 0.000 V

EVAP purge solenoid valve - command: 0 %

Remaining fuel in tank: 0.0 %

Warm-ups since DTC cleared: 0 Counts

Distance since DTC cleared: 0 km

Barometric pressure sensor: 0.0 kPa

Calculated catalyst temperature: -40 °C

Control module voltage: 0.00 V

Air/Fuel equivalence ratio command: 0.00

Air/Fuel equivalence ratio command: 0.00 lambda

Ambient air temperature: -40 °C

Throttle position - target: 0 %

Fuel alcohol content: 0 %

Electronic throttle control (ETC) system - forced engine shutdown: No

Reduced engine power: Inactive

Wide open throttle: No

APP sensor 1 and 2: Agree

Electronic throttle control (ETC) - motor: Enabled

Throttle position sensors 1 and 2: Agree

Cooling fan relays 2 and 3 - command: Off

Cooling fan relay 1 - command: Off

A/C request: No

A/C cut-off due to A/C pressure out of range: No

A/C off for WOT: No

A/C high side pressure switch: Inactive

A/C compressor clutch relay - command: Off

Brake pedal position sensor - fully released learn status: Incomplete

Extended travel brake pedal position signal: Inactive

TCC/cruise control brake pedal switch: Released

Brake pedal position circuit signal: Closed

Brake pedal position sensor - signal: Released

Clutch pedal starter inhibit switch: On

Upshift indicator command: Off

Clutch pedal switch: Released

Reverse position switch: Off

O2 sensor 2, bank 1 - heater: Off

O2 sensor 1, bank 1 - heater: Off

Engine oil pressure switch: Ok

Low engine oil level indicator command: Off

Low engine oil pressure indicator - command: Off

Fuel volatility: Low

Cold start: No

EVAP vent solenoid valve - command: Not Venting

P/N switch: Inactive

Engine controls ignition relay - command: Off

Ignition accessory signal: Off

Fuel enrichment - hot catalyst: No

Fuel enrichment - hot coolant: Inactive

Power enrichment: Inactive

Fuel pump relay - command: Off

Fuel control loop status: Open

Deceleration fuel cut-off: Inactive

Fuel trim learn: Disabled

Throttle position - performance test: Ok

MAP - performance test 2: Ok

MAP - performance test 1: Ok

MAF performance test: Ok

A/C high side pressure sensor: 0.00 V

Engine oil - temperature calculated: -40 °C

Fuel level sensor: 0.00 V

Traction control torque request signal: 0.0 %

Crankshaft position - active counter: 0 Counts

Crankshaft position - resync counter: 0 Counts

Coolant temperature at engine start: -40 °C

Traction control torque delivered signal: 0 %

Fuel trim memory cell: 0

Torque management ignition timing retard: 0.0 °

Knock retard: 0 °

Calculated air flow: 0.00 g/sec

Target idle speed: 0 rpm

Total number of misfire: 0 Counts

Misfire historic, cylinder 1: 0 Counts

Misfire historic, cylinder 2: 0 Counts

Misfire, cylinder 3 - historic: 0 Counts

Misfire historic, cylinder 4: 0 Counts

Current misfire, cylinder 2: 0 Counts

Current misfire, cylinder 1: 0 Counts

Current misfire, cylinder 3: 0 Counts

Current misfire, cylinder 4: 0 Counts

Cycles of misfire data: 0 Counts

Warm-ups without emission malfunctions: 0 Counts

Warm-ups without non-emission malfunctions: 0 Counts

Accelerator pedal - position sensors: 0 %

Throttle - position: 0 %

Accelerator pedal position sensor 1: 0 %

Accelerator pedal position sensor 2: 0 %

Throttle position sensor 1: 0 %

Throttle position sensor 2: 0 %

Throttle position sensor 2: 0.00 V

Throttle position sensor 1: 0.00 V

Accelerator pedal position sensor 2: 0.00 V

Accelerator pedal position sensor 1: 0.00 V

Injection time, bank 1: 0.00 ms

Total knock retard: 0 °

Mass air flow sensor: 0 Hz

Misfire diagnostic engine speed: 0 rpm

Misfire diagnostic engine load: 0 %

Fuel tank - rated capacity: 0 L

Accelerator pedal - position: 0 %

Remaining fuel in tank: 0 L

Catalyst monitor - test counter: 0 Counts

MIL - control circuit high voltage test status: Malfunction

MIL - control circuit low voltage test status: Malfunction

MIL - control circuit open test status: Malfunction

Fuel pump relay - control circuit high voltage test status: Malfunction

Fuel pump relay - control circuit low voltage test status: Malfunction

Fuel pump relay - control circuit open test status: Malfunction

A/C compressor clutch relay - control circuit high voltage test status: Malfunction

A/C compressor clutch relay - control circuit low voltage test status: Malfunction

A/C compressor clutch relay - control circuit open test status: Malfunction

Cooling fan motor - command: 0 %

Throttle position sensor 1 - fully close learn: 0.00 V

Throttle position sensor 2 - fully close learn: 0.00 V

Engine off time: 00:00:00

Throttle motor - PWM control signal: 0 %

Intake camshaft position actuator solenoid valve - control circuit high voltage test status: Malfunction

Intake camshaft position actuator solenoid valve - control circuit low voltage test status: Malfunction

Intake camshaft position actuator solenoid valve - control circuit open test status: Malfunction

Exhaust camshaft position actuator solenoid valve - control circuit high voltage test status: Malfunction

Exhaust camshaft position actuator solenoid valve - control circuit low voltage test status: Malfunction

Exhaust camshaft position actuator solenoid valve - control circuit open test status: Malfunction

Ignition coil 1 - control circuit high voltage test status: Malfunction

Ignition coil 1 - control circuit low voltage test status: Malfunction

Ignition coil 1 - control circuit open test status: Malfunction

Ignition coil 2 - control circuit high voltage test status: Malfunction

Ignition coil 2 - control circuit low voltage test status: Malfunction

Ignition coil 2 - control circuit open test status: Malfunction

Ignition coil 3 - control circuit high voltage test status: Malfunction

Ignition coil 3 - control circuit low voltage test status: Malfunction

Ignition coil 3 - control circuit open test status: Malfunction

Ignition coil 4 - control circuit high voltage test status: Malfunction

Ignition coil 4 - control circuit low voltage test status: Malfunction

Ignition coil 4 - control circuit open test status: Malfunction

Cylinder 1 injector - control circuit high voltage test status: Malfunction

Cylinder 1 injector - control circuit low voltage test status: Malfunction

Cylinder 1 injector - control circuit open test status: Malfunction

Cylinder 2 injector - control circuit high voltage test status: Malfunction

Cylinder 2 injector - control circuit low voltage test status: Malfunction

Cylinder 2 injector - control circuit open test status: Malfunction

Cylinder 3 injector - control circuit high voltage test status: Malfunction

Cylinder 3 injector - control circuit low voltage test status: Malfunction

Cylinder 3 injector - control circuit open test status: Malfunction

Cylinder 4 injector - control circuit high voltage test status: Malfunction

Cylinder 4 injector - control circuit low voltage test status: Malfunction

Cylinder 4 injector - control circuit open test status: Malfunction

EVAP purge solenoid valve - control circuit high voltage test status: Malfunction

EVAP purge solenoid valve - control circuit low voltage test status: Malfunction

EVAP purge solenoid valve - control circuit open test status: Malfunction

EVAP vent solenoid valve - control circuit high voltage test status: Malfunction

EVAP vent solenoid valve - control circuit low voltage test status: Malfunction

EVAP vent solenoid valve - control circuit open test status: Malfunction

Cooling fan relay 1 - control circuit high voltage test status: Malfunction

Cooling fan relay 1 - control circuit low voltage test status: Malfunction

Cooling fan relay 1 - control circuit open test status: Malfunction

Cooling fan relays 2 and 3 - control circuit high voltage test status: Malfunction

Cooling fan relays 2 and 3 - control circuit low voltage test status: Malfunction

Cooling fan relays 2 and 3 - control circuit open test status: Malfunction

Camshaft position sensor: 0 rpm

Crankshaft position sensor: 0 rpm

O2 sensor 1, bank 1 - heater control circuit high voltage test status: Malfunction

O2 sensor 1, bank 1 - heater control circuit low voltage test status: Malfunction

O2 sensor 1, bank 1 - heater control circuit open test status: Malfunction

O2 sensor 2, bank 1 - heater control circuit high voltage test status: Malfunction

O2 sensor 2, bank 1 - heater control circuit low voltage test status: Malfunction

O2 sensor 2, bank 1 - heater control circuit open test status: Malfunction

5V reference voltage circuit 1: 0.00 V

5V reference voltage circuit 2: 0.00 V

O2 sensor 1, bank 1 - heater: 0 %

O2 sensor 1, bank 1 - heater: 0.0 A

O2 sensor 2, bank 1 - heater: 0.0 A

Engine controls ignition relay - control circuit high voltage test status: Malfunction

Engine controls ignition relay - control circuit low voltage test status: Malfunction

Engine controls ignition relay - control circuit open test status: Malfunction

Engine controls ignition relay - feedback signal: 0.0 V

Cruise control: Inactive

A/C disengagement 1st history: None

A/C disengagement 2nd history: None

A/C disengagement 3rd history: None

A/C disengagement 4th history: None

A/C disengagement 5th history: None

A/C disengagement 6th history: None

A/C disengagement 7th history: None

A/C disengagement 8th history: None

Fuel level sensor - reference command: 0.0 %

A/C high side pressure sensor: 0 kPa

Fuel trim system test state: Disabled

Short term fuel trim test average: -100 %

Long term fuel trim test average: -100 %

Long term fuel trim test average without purge: -100 %

Knocking detected, cylinder 2: No

Knocking detected, cylinder 4: No

Knocking detected, cylinder 3: No

Knocking detected, cylinder 1: No

Injector, cylinder 4 - disabled, misfire detected: No

Injector, cylinder 3 - disabled, misfire detected: No

Injector disabled, cylinder 2 - misfire detected: No

Injector disabled, cylinder 1 - misfire detected: No

Exhaust camshaft position - command: 0 %

Intake camshaft position - command: 0 %

O2 sensor 2, bank 1 - heater: 0 %

Exhaust camshaft - position: 0 °

Intake camshaft - position: 0 °

Exhaust camshaft - target position: 0 °

Intake camshaft position - target: 0 °

Exhaust camshaft - position variance: 0 °

Intake camshaft position - variance: 0 °

Exhaust camshaft position active counter: 0 Counts

Intake camshaft position - active counter: 0 Counts

Transmission oil temperature: -40 °C

Output shaft speed sensor: 0 rpm

Torque delivered signal: 0.00 N·m

MAP sensor: 0.00 V

Intake manifold pressure: 0 kPa

Start-up IAT sensor: -40 °C

Clutch pedal position sensor: 0.00 V

Clutch pedal position sensor - learned apply position: 0.00 V

Clutch pedal - position learn status: Performed successfully

Clutch pedal position sensor - learned release position: 0.00 V

Clutch pedal position sensor: 0 %

Service vehicle soon (SVS) indicator - command: Off

MIL - requested by DTC: No

Check engine telltale: Off

Drop-throttle detected while traction control active: No

Traction control: Inactive

Drop-throttle - status: Inactive

Drag control - status: Inactive

5V reference voltage circuit 2: Ok

5V reference voltage circuit 1: Ok

Fuel composition learn: Inactive

Redundant odometer memory: Not present

Transmission OSS signal - replicated: 0 rpm

Torque request inhibit - minimum torque: No

Torque request inhibit - fuel: No

Torque request inhibit - TAC limit: No

Torque request inhibit - ignition timing: No

Torque request inhibit - ignition timing advance: No

Torque request inhibit - TAC: No

Torque request inhibit - minimum idle: No

Throttle body - idle air flow compensation: 0 %

Catalyst monitor - test result: No decision

Catalyst monitor - not at idle test conditions met: No

Catalyst monitor - test state: Inactive

Reduced engine power history: None

Recommended maximum fuel alcohol content: 0.0 %

Fuel composition sensor: 0 Hz

Brake pedal position sensor: 0.00 V

Brake pedal position sensor - learned released position: 0.00 V

Brake pedal position sensor: 0 %

Fuel economy mode switch: Circuit low voltage

Fuel economy mode: Inactive

Fuel economy mode request: Off

Fuel economy mode switch: 0.0 V

Accelerator pedal position sensor 1 - learned applied position: 0 %

Accelerator pedal position sensor 2 - learned applied position: 0 %

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Control module voltage: 0.00 V

Throttle position - target: 0 %

Extended travel brake pedal position signal: Inactive

TCC/cruise control brake pedal switch: Released

Brake pedal position circuit signal: Closed

Brake pedal position sensor - signal: Released

Clutch pedal switch: Released

Starter relay - command: Off

Traction control torque request signal: 0.0 %

Traction control torque delivered signal: 0 %

Torque management ignition timing retard: 0.0 °

Target idle speed: 0 rpm

Throttle - position: 0 %

Cruise control - disengagement 1st history: Brake pedal applied

Cruise control - disengagement 2nd history: Brake pedal applied

Cruise control - disengagement 3rd history: Brake pedal applied

Cruise control - disengagement 4th history: Brake pedal applied

Cruise control - disengagement 5th history: Brake pedal applied

Cruise control - disengagement 6th history: Brake pedal applied

Cruise control - disengagement 7th history: Brake pedal applied

Cruise control - disengagement 8th history: Brake pedal applied

Accelerator pedal - position: 0 %

Cruise control 'On'/'Off' switch: Off

Cruise control 'Set/Coast' switch: Off

Cruise control 'Cancel' switch: Inactive

Cruise control 'Resume/Accelerate' switch: Off

Cruise control: Inactive

Torque delivered signal: 0.00 N·m

Drop-throttle detected while traction control active: No

Traction control: Inactive

Drop-throttle - status: Inactive

Drag control - status: Inactive

Transmission OSS signal - replicated: 0 rpm

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Control module voltage: 0.00 V

TCC/cruise control brake pedal switch: Released

Brake pedal position circuit signal: Closed

Brake pedal position sensor - signal: Released

Clutch pedal starter inhibit switch: On

Engine oil pressure switch: Ok

Starter relay - command: Off

P/N switch: Inactive

Engine controls ignition relay - command: Off

Ignition accessory signal: Off

Crank request signal: No

Generator F terminal signal: 0.0 %

Immobilizer - fuel enable: No

ECM in immobilizer fail enable mode: No

Immobilizer - fuel disable: Inactive

Immobilizer - fuel disable until ignition off: No

Immobilizer automatic learn timer: Inactive

Accelerator pedal - position: 0 %

Starter relay - control circuit high voltage test status: Malfunction

Starter relay - control circuit low voltage test status: Malfunction

Starter relay - control circuit open test status: Malfunction

Generator L-terminal - command: 0.0 %

Engine controls ignition relay - control circuit high voltage test status: Malfunction

Engine controls ignition relay - control circuit low voltage test status: Malfunction

Engine controls ignition relay - control circuit open test status: Malfunction

Engine controls ignition relay - feedback signal: 0.0 V

Generator L-terminal circuit - high voltage test status: Malfunction

Generator L-terminal circuit - low voltage test status: Malfunction

Generator L-terminal circuit - open test status: Malfunction

Remote vehicle start disable history 1: None

Remote vehicle start disable history 2: None

Remote vehicle start disable history 3: None

Remote vehicle start disable history 4: None

Remote vehicle start disable history 5: None

Remote vehicle start disable history 6: None

Remote vehicle start disable history 7: None

Remote vehicle start disable history 8: None

ECM response source: Ignition switch start

ECM authentication status: Unknown

ECM challenge status: Invalid

Immobilizer - security information programmed: No

Immobilizer system - status: Standby

Immobilizer - password learn: Disabled

Immobilizer - security code accepted: No

Immobilizer - security code function: Not present

Immobilizer - security code programmed: No

Immobilizer - security code lockout: Inactive

Immobilizer - password learn scan tool delay: Inactive

Immobilizer auto learn counter: 0 Counts

MIL - requested by DTC: No

Electric power management - inhibit reason: None

Recommended maximum fuel alcohol content exceeded: No

Recommended maximum fuel alcohol content when recommended maximum fuel alcohol content exceeded: 0.0 %

Fuel alcohol content when recommended maximum fuel alcohol content exceeded: 0.0 %

Ambient air temperature when recommended maximum fuel alcohol content exceeded: -40 °C

Ignition cycles since recommended maximum fuel alcohol content exceeded: 0 Counts

Distance since recommended maximum fuel alcohol content exceeded: 0 km

Fuel consumed since recommended maximum fuel alcohol content exceeded: 0 L

Refueling events since recommended maximum fuel alcohol content exceeded: 0 Counts

Engine load: 0.0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim: -100 %

Long term fuel trim: -100 %

MAP sensor: 0.0 kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Intake air temperature sensor: -40 °C

Mass air flow sensor: 0.00 g/sec

O2 sensor 1, bank 1: 0.000 V

O2 sensor 2, bank 1: 0.000 V

EVAP purge solenoid valve - command: 0 %

Remaining fuel in tank: 0.0 %

Warm-ups since DTC cleared: 0 Counts

Distance since DTC cleared: 0 km

Fuel tank pressure sensor: 0 Pa

Barometric pressure sensor: 0.0 kPa

Calculated catalyst temperature: -40 °C

Control module voltage: 0.00 V

Air/Fuel equivalence ratio command: 0.00

Air/Fuel equivalence ratio command: 0.00 lambda

Ambient air temperature: -40 °C

Throttle position - target: 0 %

Fuel alcohol content: 0 %

A/C request: No

A/C cut-off due to A/C pressure out of range: No

A/C off for WOT: No

A/C compressor clutch relay - command: Off

Extended travel brake pedal position signal: Inactive

Brake pedal position circuit signal: Closed

Brake pedal position sensor - signal: Released

Clutch pedal starter inhibit switch: On

Clutch pedal switch: Released

O2 sensor 2, bank 1 - heater: Off

O2 sensor 1, bank 1 - heater: Off

Engine oil pressure switch: Ok

Engine oil level switch: Ok

Cold start: No

EVAP vent solenoid valve - command: Not Venting

Starter relay - command: Off

P/N switch: Inactive

Engine controls ignition relay - command: Off

Ignition accessory signal: Off

Crank request signal: No

Fuel enrichment - hot catalyst: No

Fuel enrichment - hot coolant: Inactive

Power enrichment: Inactive

Fuel pump relay - command: Off

Fuel control loop status: Open

Deceleration fuel cut-off: Inactive

Fuel trim learn: Disabled

Generator F terminal signal: 0.0 %

Fuel level sensor: 0.00 V

Coolant temperature at engine start: -40 °C

Fuel trim memory cell: 0

Target idle speed: 0 rpm

Distance since first malfunction: 0 km

Distance since last malfunction: 0 km

Ignition cycles with malfunction since 1st malfunction: 0 Counts

Ignition cycles without malfunction since last malfunction: 0 Counts

Ignition cycles without completed test since 1st malfunction: 0 Counts

Accelerator pedal - position sensors: 0 %

Throttle - position: 0 %

Accelerator pedal position sensor 1: 0 %

Accelerator pedal position sensor 2: 0 %

Throttle position sensor 2: 0.00 V

Throttle position sensor 1: 0.00 V

Accelerator pedal position sensor 2: 0.00 V

Accelerator pedal position sensor 1: 0.00 V

Injection time, bank 1: 0.00 ms

Total knock retard: 0 °

Mass air flow sensor: 0 Hz

Accelerator pedal - position: 0 %

Fuel pump relay - control circuit high voltage test status: Malfunction

Fuel pump relay - control circuit low voltage test status: Malfunction

Fuel pump relay - control circuit open test status: Malfunction

Throttle position sensor 1 - fully close learn: 0.00 V

Throttle position sensor 2 - fully close learn: 0.00 V

Engine off time: 00:00:00

Throttle motor - PWM control signal: 0 %

Generator L-terminal - command: 0.0 %

Cylinder 1 injector - control circuit high voltage test status: Malfunction

Cylinder 1 injector - control circuit low voltage test status: Malfunction

Cylinder 1 injector - control circuit open test status: Malfunction

Cylinder 2 injector - control circuit high voltage test status: Malfunction

Cylinder 2 injector - control circuit low voltage test status: Malfunction

Cylinder 2 injector - control circuit open test status: Malfunction

Cylinder 3 injector - control circuit high voltage test status: Malfunction

Cylinder 3 injector - control circuit low voltage test status: Malfunction

Cylinder 3 injector - control circuit open test status: Malfunction

Cylinder 4 injector - control circuit high voltage test status: Malfunction

Cylinder 4 injector - control circuit low voltage test status: Malfunction

Cylinder 4 injector - control circuit open test status: Malfunction

Crankshaft position sensor: 0 rpm

O2 sensor 1, bank 1 - heater control circuit high voltage test status: Malfunction

O2 sensor 1, bank 1 - heater control circuit low voltage test status: Malfunction

O2 sensor 1, bank 1 - heater control circuit open test status: Malfunction

O2 sensor 2, bank 1 - heater control circuit high voltage test status: Malfunction

O2 sensor 2, bank 1 - heater control circuit low voltage test status: Malfunction

O2 sensor 2, bank 1 - heater control circuit open test status: Malfunction

5V reference voltage circuit 1: 0.00 V

5V reference voltage circuit 2: 0.00 V

O2 sensor 1, bank 1 - heater: 0 %

O2 sensor 1, bank 1 - heater: 0.0 A

O2 sensor 2, bank 1 - heater: 0.0 A

Engine controls ignition relay - feedback signal: 0.0 V

Cruise control 'On'/'Off' switch: Off

Cruise control 'Set/Coast' switch: Off

Cruise control 'Cancel' switch: Inactive

Cruise control 'Resume/Accelerate' switch: Off

Cruise control: Inactive

Knocking detected, cylinder 2: No

Knocking detected, cylinder 4: No

Knocking detected, cylinder 3: No

Knocking detected, cylinder 1: No

O2 sensor 2, bank 1 - heater: 0 %

Exhaust camshaft - position: 0 °

Intake camshaft - position: 0 °

Exhaust camshaft - target position: 0 °

Intake camshaft position - target: 0 °

Transmission oil temperature: -40 °C

Output shaft speed sensor: 0 rpm

Torque delivered signal: 0.00 N·m

MAP sensor: 0.00 V

Start-up IAT sensor: -40 °C

Clutch pedal position sensor: 0 %

Traction control: Inactive

Recommended maximum fuel alcohol content: 0.0 %

Brake pedal position sensor: 0.00 V

Transmission OSS signal - replicated: Off

Engine coolant temperature sensor: -40 °C

Vehicle speed sensor: 0 km/h

Intake air temperature sensor: -40 °C

Remaining fuel in tank: 0.0 %

Barometric pressure sensor: 0.0 kPa

Catalyst monitor - enabled this ignition cycle: --

O2S/HO2S monitor enabled this ignition cycle: --

EGR/Camshaft position monitor enabled this ignition cycle: --

Catalyst monitor - complete this ignition cycle: --

O2S/HO2S monitor complete this ignition cycle: --

HO2S heater monitor complete this ignition cycle: --

EGR/Camshaft position monitor complete this ignition cycle: --

Control module voltage: 0.00 V

Ambient air temperature: -40 °C

Fuel alcohol content: 0 %

TCC/cruise control brake pedal switch: Released

Brake pedal position circuit signal: Closed

Brake pedal position sensor - signal: Released

Clutch pedal switch: Released

Cold start: No

Coolant temperature at engine start: -40 °C

Remaining fuel in tank: 0 L

Engine off time: 00:00:00

Start-up IAT sensor: -40 °C

MIL - requested by DTC: No

Check engine telltale: Off

Fuel composition learn: Inactive

Check engine telltale - request: No

Misfire monitor enabled: No

Misfire monitor complete: Yes

Fuel system monitor - enabled: No

Fuel system monitor - complete: Yes

Component monitor - enabled: No

Component monitor - complete: Yes

Catalyst monitor - enabled: --

Catalyst monitor - enabled: --

O2S/HO2S monitor enabled: --

EVAP monitor - enabled: --

HO2S heater monitor enabled: --

Secondary air injection system - monitor enabled: --

EGR/Camshaft position monitor enabled: --

Catalyst monitor - complete: --

Catalyst monitor - complete: --

O2S/HO2S monitor complete: --

EVAP monitor - complete: --

HO2S heater monitor complete: --

Secondary air injection system - monitor complete: --

EGR/Camshaft position monitor - complete: --

Number of DTC: 0 Counts

Calibration history buffer: Unlocked

Engine calibration part number history 1: --

Calibration verification number - history 1: --

Engine calibration part number history 1 counter: --

Engine calibration part number history 2: --

Calibration verification number - history 2: --

Engine calibration part number history 2 counter: --

Engine calibration - part number history 3: --

Calibration verification number - history 3: --

Engine calibration - part number history 3 counter: --

Engine calibration - part number history 4: --

Calibration verification number - history 4: --

Engine calibration - part number history 4 counter: --

Engine calibration - part number history 5: --

Calibration verification number - history 5: --

Engine calibration - part number history 5 counter: --

Engine calibration - part number history 6: --

Calibration verification number - history 6: --

Engine calibration - part number history 6 counter: --

Engine calibration - part number history 7: --

Calibration verification number - history 7: --

Engine calibration - part number history 7 counter: --

Engine calibration - part number history 8: --

Calibration verification number - history 8: --

Engine calibration - part number history 8 counter: --

Engine calibration - part number history 9: --

Calibration verification number - history 9: --

Engine calibration - part number history 9 counter: --

Engine calibration part number history 10: --

Calibration verification number - history 10: --

Engine calibration part number history 10 counter: --

VIN no: --

A/C compressor clutch relay

Exhaust camshaft position actuator

Intake camshaft position actuator

Exhaust camshaft position actuator solenoid valve

Intake camshaft position actuator solenoid valve

Cooling fan

Cooling fan relays 1, 2 and 3

Cooling fan relays 2 and 3

Cooling fan

Engine controls ignition relay

Engine speed

Throttle position

Throttle position

Evaporative emission (EVAP) system, canister purge valve

Evaporative emission (EVAP) system, canister vent valve

EVAP purge/seal

Fuel control loop status

Cylinder power balance

Fuel pump relay

Fuel pump enable

Fuel injector balance

Generator L terminal

Idle ignition timing

Ignition timing retard

Check engine telltale

O2 sensor 1, bank 1 heater

O2 sensor 2, bank 1 heater

Starter relay

Starter relay