Car, CHEVROLET, Silverado, 2017, 4.3L (LV1) - 4.3L (LV1)

4.3L (LV1) - 4.3L (LV1) - 0

Identification

Mobile equipment identifier: --

Hardware version: --

VIN no: W0LGT8EBXA1007787

Engine type: 1

Engine name: 87

Body type: Station wagon

System identification: 01

System name: --

Subscriber ID: O100057235

Programming date: 20 11 11 04

Identifier: 00 00

System code: 00

XML configuration compatibility identifier: 1

XML data file part number: 0

XML data file alpha code:

Previous subscriber ID: *10MDZ7

2nd previous subscriber ID: *10MDZ7

Manufacturer enable counter (MEC): 0

Trailer hitch: --

ECU diagnostic address: --

Manufacturer`s traceability number: --

Broadcast code: --

ROM ID: --

Boot software part number: 0

Software version: 12654173

Software module 1 identifier: 12654173

Software module 2 identifier: 55577673

Software module 3 identifier: 55577209

Software module 4 identifier: 55577673

Software module 5 identifier: 55573530

Software module 6 identifier: 55573530

Software module 9 identifier: --

Software module 7 identifier: --

Software module 8 identifier: --

Software module 10 identifier: --

End model part number: 55577619

Base model part number: 55574337

Software part number alpha code: --

Software module 1 identifier alpha code: AA

Software module 2 identifier alpha code: AA

Software module 3 identifier alpha code: AA

Software module 4 identifier alpha code: AA

Software module 5 identifier alpha code: --

Software module 6 identifier alpha code: --

Software module 7 identifier alpha code: --

Software module 8 identifier alpha code: --

Software module 9 identifier alpha code: --

Software module 10 identifier alpha code: --

End model part number alpha code: 00

Base model part number alpha code: 00

GMLAN identification data - bus 1 type: High speed CAN-bus

GMLAN identification data - GMLAN kernel 1 version: 00 00

GMLAN identification data - data dictionary 1 version: --

GMLAN identification data - bus 2 type: --

GMLAN identification data - GMLAN kernel 2 version: --

GMLAN identification data - data dictionary 2 version: --

DTC

Controls

Clear DTC

Data stream

Fuel rail pressure sensor: -- kPa

EVAP monitor complete: --

Engine load: 0.0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim bank 1: -100 %

Long term fuel trim bank 1: -100 %

Short term fuel trim bank 2: -100 %

Long term fuel trim bank 2: -100 %

Fuel pressure sensor: 0 kPa

MAP sensor: 0.0 kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Intake air temperature sensor 1: -40 °C

Intake air temperature sensor: -40 °C

Mass air flow sensor: 0.00 g/sec

Fuel rail pressure sensor 1: 0.0 MPa

Fuel rail pressure sensor: 0.0 MPa

EVAP purge solenoid valve command: 0 %

Remaining fuel in tank: 0.0 %

Warm-ups since DTC cleared: 0 Counts

Fuel tank pressure sensor: 0.00 in. H2O

Baro: 0.0 kPa

Barometric pressure sensor 1: 0 kPa

Initialized fuel alcohol content: 0.0 %

Calculated catalyst temperature bank 1: -40 °C

Calculated catalyst temperature bank 2: -40 °C

EVAP monitor enabled this ignition cycle: --

Ignition 1 signal: 0.00 V

Air/Fuel equivalence ratio command: 0.00

Air/Fuel equivalence ratio command: 0.00 lambda

Ambient air temperature: -40 °C

Target throttle position: 0 %

Fuel alcohol content: 0 %

Fuel pressure drop - cylinder 5 injector: -- kPa

Fuel pressure drop - cylinder 6 injector: -- kPa

Fuel pressure drop - cylinder 7 injector: -- kPa

Fuel pressure drop - cylinder 8 injector: -- kPa

Fuel pressure drop - cylinder 1 injector: 0 kPa

Fuel pressure drop - cylinder 2 injector: -- kPa

Fuel pressure drop - cylinder 3 injector: -- kPa

Fuel pressure drop - cylinder 4 injector: -- kPa

Electronic throttle control (ETC) system forced engine shutdown: No

Reduced engine power: Inactive

Wide open throttle: No

APP sensor 1 and 2: Agree

Electronic throttle control (ETC) motor: Enabled

Throttle position sensors 1 and 2: Agree

A/C request: No

A/C cut-off due to A/C pressure out of range: No

A/C Off for WOT: No

A/C compressor clutch relay command: Off

A/C compressor operation: Not allowed

Brake pedal position sensor fully released learn status: Incomplete

Extended travel brake pedal position signal: Released

TCC/Cruise control brake pedal switch: Released

Brake pedal position circuit signal: Released

Brake pedal position sensor signal: Released

Skip shift indicator command: Off

Clutch pedal starter inhibit switch: On

Upshift Indicator command: Off

Clutch pedal switch: Released

Reverse position switch: Off

Skip shift solenoid actuator command: Disabled

O2 sensor 2, bank 2 heater: Off

O2 sensor 2, bank 1 heater: Off

O2 sensor 1, bank 2 heater: Off

O2 sensor 1, bank 1 heater: Off

Engine oil pressure switch: Ok

Change engine oil indicator command: Off

Low engine oil pressure indicator command: Off

Engine oil level switch: Ok

Fuel volatility: Low

Cold start: No

EVAP vent solenoid valve command: Not Venting

Front axle engagement feedback switch: Disengaged

P/N switch: In gear

Engine controls ignition relay command: Off

Ignition accessory signal: Off

Fuel enrichment - hot catalyst: Inactive

Fuel enrichment - hot coolant: Inactive

Power enrichment: Inactive

Fuel control loop status: Open

Deceleration fuel cut-off: Inactive

Fuel trim learn: Disabled

Cylinder 6 deactivation solenoid valve command: Off

Cylinder 7 deactivation solenoid valve command: Off

Cylinder 1 deactivation solenoid valve command: Off

Cylinder 3 deactivation solenoid valve command: Off

Cylinder 4 deactivation solenoid valve command: Off

Cylinder Deactivation System Command: Inactive

Throttle position performance test: Ok

MAP performance test 2: Ok

MAP performance test 1: Ok

Cylinder deactivation performance test: Ok

MAF performance test: Ok

A/C high side pressure sensor: 0.00 V

Fuel tank pressure sensor: 0.00 V

Engine oil temperature calculated: -40 °C

Fuel level sensor left tank: 0.00 V

Fuel level sensor: 0.00 V

Crankshaft position active counter: 0 Counts

Crankshaft position resync counter: 0 Counts

Coolant temperature at engine start: -40 °C

Fuel trim memory cell: 0

Torque management ignition timing retard: 0.0 °

Knock retard: 0 °

Calculated air flow: 0.00 g/sec

Target idle speed: 0 rpm

Current misfire, cylinder 5: 0 Counts

Current misfire, cylinder 6: 0 Counts

Current misfire, cylinder 7: 0 Counts

Current misfire, cylinder 8: 0 Counts

Misfire historic, cylinder 5: 0 Counts

Misfire historic, cylinder 6: 0 Counts

Misfire historic, cylinder 7: 0 Counts

Misfire historic, cylinder 8: 0 Counts

Total number of misfire: 0 Counts

Misfire historic, cylinder 1: 0 Counts

Misfire historic, cylinder 2: 0 Counts

Misfire historic, cylinder 3: 0 Counts

Misfire historic, cylinder 4: 0 Counts

Current misfire, cylinder 2: 0 Counts

Current misfire, cylinder 1: 0 Counts

Current misfire, cylinder 3: 0 Counts

Current misfire, cylinder 4: 0 Counts

Cycles of misfire data: 0 Counts

Warm-ups without emission malfunctions: 0 Counts

Warm-ups without non-emission malfunctions: 0 Counts

Distance since DTC cleared: 0 km

EVAP malfunction history: None

Accelerator pedal position sensors: 0 %

Throttle position: 0 %

Accelerator pedal position sensor 1: 0 %

Accelerator pedal position sensor 2: 0 %

Throttle position sensor 1: 0 %

Throttle position sensor 2: 0 %

Throttle position sensor 2: 0.00 V

Throttle position sensor 1: 0.00 V

Accelerator pedal position sensor 2: 0.00 V

Accelerator pedal position sensor 1: 0.00 V

Injection time bank 1: 0.00 ms

Injection time bank 2: 0.00 ms

Total knock retard: 0 °

Mass air flow sensor: 0 Hz

Misfire diagnostic engine speed: 0 rpm

Misfire diagnostic engine load: 0.0 %

EVAP service bay test result: No test result

EVAP service bay test abort reason: None

EVAP service bay test status: Waiting for purge enable

Fuel tank rated capacity: 0 L

Accelerator pedal position: 0 %

Remaining fuel in tank: 0 L

Fuel level sensor right tank: 0.00 V

Catalyst monitor test counter bank 1: 0 Counts

Catalyst monitor test counter bank 2: 0 Counts

MIL control circuit high voltage test status: Malfunction

MIL control circuit low voltage test status: Malfunction

MIL control circuit open test status: Malfunction

Fuel pump relay control circuit high voltage test status: Malfunction

Fuel pump relay control circuit low voltage test status: Malfunction

Fuel pump: Off

Fuel pump relay control circuit open test status: Malfunction

A/C compressor clutch relay control circuit high voltage test status: Malfunction

A/C compressor clutch relay control circuit low voltage test status: Malfunction

A/C compressor clutch relay control circuit open test status: Malfunction

Throttle position sensor 1 fully close learn: 0.00 V

Throttle position sensor 2 fully close learn: 0.00 V

Engine off time: 00:00:00

Throttle motor PWM control signal: 0 %

Camshaft position actuator solenoid valve control circuit high voltage test status: Malfunction

Camshaft position actuator solenoid valve control circuit low voltage test status: Malfunction

Intake camshaft position actuator, bank 1: Off

Camshaft position actuator solenoid valve control circuit open test status: Malfunction

Ignition coil 1 control circuit high voltage test status: Malfunction

Ignition coil 1 control circuit low voltage test status: Malfunction

Ignition coil 1 control circuit open test status: Malfunction

Ignition coil 2 control circuit high voltage test status: Malfunction

Ignition coil 2 control circuit low voltage test status: Malfunction

Ignition coil 2 control circuit open test status: Malfunction

Ignition coil 3 control circuit high voltage test status: Malfunction

Ignition coil 3 control circuit low voltage test status: Malfunction

Ignition coil 3 control circuit open test status: Malfunction

Ignition coil 4 control circuit high voltage test status: Malfunction

Ignition coil 4 control circuit low voltage test status: Malfunction

Ignition coil 4 control circuit open test status: Malfunction

Ignition coil 5 control circuit high voltage test status: Malfunction

Ignition coil 5 control circuit low voltage test status: Malfunction

Ignition coil 5 control circuit open test status: Malfunction

Ignition coil 6 control circuit high voltage test status: Malfunction

Ignition coil 6 control circuit low voltage test status: Malfunction

Ignition coil 6 control circuit open test status: Malfunction

Ignition coil 7 control circuit high voltage: Malfunction

Ignition coil 7 control circuit low voltage: Malfunction

Ignition coil 7 control circuit open test status: Malfunction

Ignition coil 8 control circuit high voltage test status: Malfunction

Ignition coil 8 control circuit low voltage test status: Malfunction

Ignition coil 8 control circuit open test status: Malfunction

EVAP purge solenoid valve control circuit high voltage test status: Malfunction

EVAP purge solenoid valve control circuit low voltage test status: Malfunction

EVAP purge solenoid valve control circuit open test status: Malfunction

EVAP vent solenoid valve control circuit high voltage test status: Malfunction

EVAP vent solenoid valve control circuit low voltage test status: Malfunction

EVAP vent solenoid valve control circuit open test status: Malfunction

Reverse inhibit solenoid actuator control circuit high voltage test status: Malfunction

Reverse inhibit solenoid actuator control circuit low voltage test status: Malfunction

Reverse inhibit solenoid actuator command: Off

Reverse inhibit solenoid actuator control circuit open test status: Malfunction

Skip shift solenoid actuator control circuit high voltage test status: Malfunction

Skip shift solenoid actuator control circuit low voltage test status: Malfunction

Skip shift solenoid actuator control circuit open test status: Malfunction

Camshaft position sensor: 0 rpm

Crankshaft position sensor: 0 rpm

O2 sensor 1, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit open test status: Malfunction

O2 sensor 2, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit low voltage test status: Malfunction

HO2S heater control circuit open test status bank 1 sensor 2: Malfunction

O2 sensor 1, bank 2 heater control circuit high voltage test status: Malfunction

O2 sensor 1, bank 2 heater control circuit low voltage test status: Malfunction

O2 sensor 1, bank 2 heater control circuit open test status: Malfunction

O2 sensor 2, bank 2 heater control circuit high voltage test status: Malfunction

O2 sensor 2, bank 2 heater control circuit low voltage test status: Malfunction

O2 sensor 2, bank 2 heater control circuit open test status: Malfunction

5V reference voltage circuit 1: 0.00 V

5V reference voltage circuit 2: 0.00 V

Fuel pressure regulator high control circuit command: 0 %

O2 sensor 1, bank 1 heater: 0 %

O2 sensor 1, bank 2 heater: 0 %

O2 sensor 1, bank 1 heater: 0.00 mA

O2 sensor 2, bank 1 heater: 0.00 mA

O2 sensor 1, bank 2 heater: 0.00 mA

O2 sensor 2, bank 2 heater: 0.00 mA

Engine controls ignition relay control circuit high voltage test status: Malfunction

Engine controls ignition relay control circuit low voltage test status: Malfunction

Engine controls ignition relay control circuit open test status: Malfunction

Engine controls ignition relay feedback signal: 0.0 V

A/C disengagement 1st history: None

A/C disengagement 2nd history: None

A/C disengagement 3rd history: None

A/C disengagement 4th history: None

A/C disengagement 5th history: None

A/C disengagement 6th history: None

A/C disengagement 7th history: None

A/C disengagement 8th history: None

Cylinder 1 deactivation solenoid valve control circuit high voltage test status: Malfunction

Cylinder 3 deactivation solenoid valve control circuit high voltage test status: Malfunction

Cylinder 1 deactivation solenoid valve control circuit low voltage test status: Malfunction

Cylinder 3 deactivation solenoid valve control circuit low voltage test status: Malfunction

Cylinder 1 deactivation solenoid valve control circuit open test status: Malfunction

Cylinder 3 deactivation solenoid valve control circuit open test status: Malfunction

Cylinder 7 deactivation solenoid valve control circuit high voltage test status: Malfunction

Cylinder 7 deactivation solenoid valve control circuit low voltage test status: Malfunction

Cylinder 7 deactivation solenoid valve control circuit open test status: Malfunction

Cylinder 6 deactivation solenoid valve control circuit high voltage test status: Malfunction

Cylinder 6 deactivation solenoid valve control circuit low voltage test status: Malfunction

Cylinder 6 deactivation solenoid valve control circuit open test status: Malfunction

Cylinder 4 deactivation solenoid valve control circuit high voltage test status: Malfunction

Cylinder 4 deactivation solenoid valve control circuit low voltage test status: Malfunction

Cylinder 4 deactivation solenoid valve control circuit open test status: Malfunction

A/C high side pressure sensor: 0 kPa

EVAP service bay test inhibit reason: None

Engine off evap service bay test abort reason: None

Engine off evap service bay test inhibit reason: None

Engine off evap service bay test result: None

Distance to enable engine off evap service bay test: 0.0 km

Fuel trim system test state: Disabled

Short term fuel trim test average bank 1: -100 %

Short term fuel trim test average bank 2: -100 %

Long term fuel trim test average bank 1: -100 %

Long term fuel trim test average bank 2: -100 %

Long term fuel trim test average without purge bank 1: -100 %

Long term fuel trim test average without purge bank 2: -100 %

Knocking detected, cylinder 3: No

Knocking detected, cylinder 2: No

Knocking detected, cylinder 4: No

Knocking detected, cylinder 7: No

Knocking detected, cylinder 5: No

Knocking detected, cylinder 8: No

Knocking detected, cylinder 6: No

Knocking detected, cylinder 1: No

Injector disabled, cylinder 3 - misfire detected: No

Injector disabled, cylinder 2 - misfire detected: No

Injector disabled, cylinder 4 - misfire detected: No

Injector disabled, cylinder 7 - misfire detected: No

Injector disabled, cylinder 5 - misfire detected: No

Injector disabled, cylinder 8 - misfire detected: No

Injector disabled, cylinder 6 - misfire detected: No

Injector disabled, cylinder 1 - misfire detected: No

Target cooling fan control: 0 %

O2 sensor 2, bank 2 heater: 0 %

O2 sensor 2, bank 1 heater: 0 %

Camshaft position: 0 °

Camshaft position variance: 0 °

Camshaft position active counter: 0 Counts

Transmission oil temperature: -40 °C

Output shaft speed sensor: 0 rpm

Torque delivered signal: 0.00 N·m

Engine oil pressure control test counter: 0 Counts

MAP sensor: 0.00 V

Supercharger inlet pressure: 0.00 V

Intake air temperature sensor 1 at start: -40 °C

Start-up IAT sensor: -40 °C

Intake air temperature sensor 2: -40 °C

Barometric pressure sensor 1: 0.00 V

Barometric pressure sensor: 0.00 V

Supercharger bypass solenoid valve command: 0.0 %

Supercharger bypass solenoid valve control circuit high voltage test status: Malfunction

Supercharger bypass solenoid valve control circuit low voltage test status: Malfunction

Supercharger bypass solenoid valve control circuit open test status: Malfunction

Charge air cooler coolant pump relay control circuit high voltage test status: Malfunction

Charge air cooler coolant pump relay control circuit low voltage test status: Malfunction

Charge air cooler coolant pump relay command: Off

Charge air cooler coolant pump relay control circuit open test status: Malfunction

Distance with cylinder deactivated: 0 km

Distance with cylinder activated: 0 km

Cylinder deactivation cycles: 0 Counts

Cylinder deactivation inhibit - ECT: No

Cylinder deactivation inhibit - APP high: No

Cylinder deactivation inhibit - engine oil temperature: No

Cylinder deactivation inhibit - APP rate high: No

Cylinder deactivation inhibit - engine oil pressure: No

Cylinder deactivation inhibit - brake booster weak vacuum: No

Cylinder deactivation inhibit - ignition voltage: No

Cylinder deactivation inhibit - intake manifold weak vacuum: No

Cylinder deactivation inhibit - oil aeration: No

Cylinder deactivation inhibit - transmission shifting: No

Cylinder deactivation inhibit - maximum deactivation time exceeded: No

Cylinder deactivation inhibit - transmission range: No

Cylinder deactivation inhibit - minimum time on all cylinders: No

Cylinder deactivation inhibit - transmission gear: No

Cylinder deactivation inhibit - scan tool override: No

Cylinder deactivation inhibit - engine speed: No

Cylinder deactivation inhibit - acceleration request: --

Cylinder deactivation inhibit - A/C compressor clutch on: --

Cylinder deactivation inhibit - vehicle speed too low: --

Cylinder deactivation inhibit - heater performance: --

Cylinder deactivation inhibit - rpm limit: --

Cylinder deactivation inhibit - injector stable time: --

Cylinder deactivation inhibit - HO2S 2 test: --

Cylinder deactivation inhibit - deceleration fuel cut-off: --

Cylinder deactivation inhibit - fuel alcohol content too high: --

Cylinder deactivation inhibit - fuel alcohol content learn in progress: --

Cylinder deactivation inhibit - minimum time after TAC DTC: --

Cylinder deactivation inhibit - maximum throttle exceeded: --

Cylinder deactivation inhibit - catalyst temperature low: --

Cylinder deactivation inhibit - cylinder deactivation solenoid valve DTC: No

Cylinder deactivation inhibit - engine oil pressure sensor DTC: No

Cylinder deactivation inhibit - VSS DTC: No

Cylinder deactivation inhibit - tac system DTC: No

Cylinder deactivation inhibit - iat sensor DTC: No

Cylinder deactivation inhibit - brake booster pressure sensor DTC: No

Cylinder deactivation inhibit - ECT sensor DTC: No

Cylinder deactivation inhibit - map sensor DTC: No

Cylinder deactivation inhibit - catalyst overtemperature protection: No

Cylinder deactivation inhibit - engine controls ignition relay DTC: No

Cylinder deactivation inhibit - engine overtemperature protection: No

Cylinder deactivation inhibit - camshaft position sensor DTC: No

Cylinder deactivation inhibit - axle torque limiting: No

Cylinder deactivation inhibit - crankshaft position sensor DTC: No

Cylinder deactivation inhibit - torque reduction: No

Cylinder deactivation inhibit - misfire DTC: No

Cylinder deactivation inhibit - cylinder deactivation system DTC: --

Cylinder deactivation inhibit - hot coolant mode: --

Cylinder deactivation inhibit - calculated torque: --

Cylinder deactivation inhibit - piston protection: --

Cylinder deactivation disable history 1: None

Cylinder deactivation disable history 2: None

Cylinder deactivation disable history 3: None

Cylinder deactivation disable history 4: None

Cylinder deactivation disable history 5: None

Cylinder deactivation disable history 6: None

Cylinder deactivation disable history 7: None

Cylinder deactivation disable history 8: None

Clutch pedal position sensor: 0.00 V

Clutch pedal position sensor learned apply position: 0.00 V

Clutch pedal position learn status: Performed successfully

Clutch pedal position sensor learned release position: 0.00 V

Clutch pedal position sensor: 0 %

MIL requested by DTC: No

MIL command: Off

Traction control: Inactive

Drag control status: Inactive

Engine drag control status: Inactive

5V reference voltage circuit 4: Ok

5V reference voltage circuit 3: Ok

5V reference voltage circuit 2: Ok

5V reference voltage circuit 1: Ok

Fuel composition learn: Inactive

Fuel economy actual: 0.0 L/h

Redundant odometer memory: Not present

Torque request inhibit - minimum torque: No

Torque request inhibit - fuel: No

Torque request inhibit - TAC limit: No

Torque request inhibit - ignition timing: No

Torque request inhibit - ignition timing advance: No

Torque request inhibit - TAC: No

Torque request inhibit - minimum idle: No

Transfer case OSS: 0 rpm

5V reference voltage circuit 3: 0.00 V

5V reference voltage circuit 4: 0.00 V

Radiator coolant temperature sensor: -40 °C

Throttle body idle air flow compensation: 0 %

Cruise control: Disabled

Generator indicator command: Off

Catalyst monitor test result bank 1: No decision

Catalyst monitor test result bank 2: No decision

Catalyst monitor not at idle test conditions met: No

Catalyst monitor test state: Inactive

Reduced engine power history: None

Intake air temperature sensor 2: -40 °C

Power mode: Off

Cylinder 1 injector control circuit status: Ok

Cylinder 2 injector control circuit status: Ok

Cylinder 3 injector control circuit status: Ok

Cylinder 4 injector control circuit status: Ok

Cylinder 5 injector control circuit status: Ok

Cylinder 6 injector control circuit status: Ok

Cylinder 7 injector control circuit status: Ok

Cylinder 8 injector control circuit status: Ok

Fuel pressure regulator control circuit high voltage test status: Malfunction

Fuel pressure regulator control circuit low voltage test status: Malfunction

Fuel pressure regulator control circuit command: Off

Fuel pressure regulator control circuit open test status: Malfunction

Fuel pressure regulator high control circuit high voltage test status: Malfunction

Fuel pressure regulator high control circuit low voltage test status: Malfunction

Fuel pressure regulator high control circuit command: Off

Fuel pressure regulator high control circuit open test status: Malfunction

Intake manifold pressure: 0 kPa

Ignition coil supply voltage bank 2: Off

Ignition coil supply voltage bank 1: Off

Fuel composition sensor: 0 Hz

Accelerator pedal position sensor 2 - circuit status: Ok

Accelerator pedal position sensor 1 - circuit status: Ok

Brake pedal position sensor: 0.00 V

Brake pedal position sensor learned released position: 0.00 V

Brake pedal position sensor: 0 %

Fuel injector driver supply voltage: 0.0 V

Fuel economy mode: Inactive

Calculated barometric pressure: 0 kPa

Intake air humidity sensor: 0 Hz

Ambient humidity: 0 %

Intake air humidity sensor: 0 %

Specific humidity: 0.00 %

O2 sensor 1, bank 1: 0.00 V

O2 sensor 2, bank 1: 0.00 V

O2 sensor 1, bank 2: 0.00 V

O2 sensor 2, bank 2: 0.00 V

Crankshaft position signal output circuit high voltage test status: Malfunction

Crankshaft position signal output circuit low voltage test status: Malfunction

Crankshaft position signal output circuit open test status: Malfunction

Camshaft position signal output circuit high voltage test status: Malfunction

Camshaft position signal output circuit low voltage test status: Malfunction

Camshaft position signal output circuit open test status: Malfunction

Engine oil absolute pressure sensor: 0 kPa

Engine oil pressure: 0.00 kPa

Fuel pump command: 0 %

Target fuel pressure: 0 kPa

Short term fuel pump trim: 0.00

Long term fuel pump trim: 0.00

Fuel pressure sensor: 0.0 V

Active grille air shutter position command: 0 %

Active grille air shutter position: 0 %

Fuel rail pressure sensor initial learn: Incomplete

Fuel rail pressure sensor learn: Inactive

Fuel rail pressure sensor learned value: 0 kPa

Driver requested axle torque: -22534 N·m

Fuel rail temperature sensor 1: -40 °C

Fuel rail temperature sensor 2: -40 °C

Barometric pressure sensor 2: 0.00 V

Barometric pressure sensor 2: 0 kPa

Camshaft position sensor: 0 °

Intake camshaft position target: 0 °

Accelerator pedal position sensor 1 learned applied position: 0 %

Accelerator pedal position sensor 2 learned applied position: 0 %

A/T output speed: 0 rpm

Target fuel rail pressure: 0.0 MPa

Fuel rail pressure sensor 1: 0.00 V

Current gear: In progress

Accelerator pedal position sensor 1 learned released position: 0.00 V

Accelerator pedal position sensor 2 learned released position: 0.00 V

Engine oil pressure control solenoid valve control circuit high voltage test status: Malfunction

Engine oil pressure control solenoid valve control circuit low voltage test status: Malfunction

Engine oil pressure control solenoid valve command: Off

Engine oil pressure control solenoid valve control circuit open test status: Malfunction

Fuel rail pressure sensor 2: 0.00 V

Fuel rail pressure sensor 2: 0.0 MPa

Gate select position sensor learned position: 0 %

Gear shift position sensor learned position: 0 %

Gear shift position: Unknown

Gear position sensor learn status: Complete

Gear position sensor learn abort reason: None

Distance since excessive clutch slip detected: 0 km

Fuel rail pressure sensor 1: 0 Counts

Fuel rail pressure sensor 2: 0 Counts

Ignition on/start circuit source bypass relay control circuit high voltage test status: Malfunction

Ignition on/start circuit source bypass relay control circuit low voltage test status: Malfunction

Ignition on/start circuit source bypass relay control circuit open test status: Malfunction

Ignition on/start circuit source bypass relay control circuit open test status: Malfunction

Cruise control, PTO and traction control data

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Ignition 1 signal: 0.00 V

Target throttle position: 0 %

Brake pedal position sensor fully released learn status: Incomplete

Extended travel brake pedal position signal: Released

TCC/Cruise control brake pedal switch: Released

Brake pedal position circuit signal: Released

Brake pedal position sensor signal: Released

Engine oil level switch: Ok

Starter relay command: Off

Torque management ignition timing retard: 0.0 °

Target idle speed: 0 rpm

Throttle position: 0 %

Cruise control disengagement 1st history: Brake pedal applied

Cruise control disengagement 2nd history: Brake pedal applied

Cruise control disengagement 3rd history: Brake pedal applied

Cruise control disengagement 4th history: Brake pedal applied

Cruise control disengagement 5th history: Brake pedal applied

Cruise control disengagement 6th history: Brake pedal applied

Cruise control disengagement 7th history: Brake pedal applied

Cruise control disengagement 8th history: Brake pedal applied

Accelerator pedal position: 0 %

Cruise control "On"/"Off" switch: Off

Cruise control "Set/Coast" switch: Off

Cruise control "Cancel" switch: Inactive

Cruise control "Resume/Accelerate" switch: Off

Cruise control switch: Active

Torque delivered signal: 0.00 N·m

Traction control: Inactive

Drag control status: Inactive

Cruise control inhibit reason: Brake pedal applied

Cruise control: Disabled

Brake pedal position sensor: 0.00 V

Brake pedal position sensor learned released position: 0.00 V

Brake pedal position sensor: 0 %

Driver requested axle torque: -22534 N·m

Electrical and immobilizer data

Engine coolant temperature sensor: -40 °C

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

TCC/Cruise control brake pedal switch: Released

Brake pedal position circuit signal: Released

Brake pedal position sensor signal: Released

Engine oil pressure switch: Ok

Starter relay command: Off

P/N switch: In gear

Engine controls ignition relay command: Off

Ignition accessory signal: Off

Remote vehicle start request signal: Off

Crank request signal: No

Generator F terminal signal: 0.0 %

Accelerator pedal position: 0 %

Starter relay control circuit high voltage test status: Malfunction

Starter relay control circuit low voltage test status: Malfunction

Starter relay control circuit open test status: Malfunction

Generator L - terminal command: 0.0 %

Engine controls ignition relay control circuit high voltage test status: Malfunction

Engine controls ignition relay control circuit low voltage test status: Malfunction

Engine controls ignition relay control circuit open test status: Malfunction

Engine controls ignition relay feedback signal: 0.0 V

Generator L-terminal circuit high voltage test status: Malfunction

Generator L-terminal circuit low voltage test status: Malfunction

Generator L - terminal command: Off

Generator L-terminal circuit open test status: Malfunction

Remote vehicle start disable history 1: None

Remote vehicle start disable history 2: None

Remote vehicle start disable history 3: None

Remote vehicle start disable history 4: None

Remote vehicle start disable history 5: None

Remote vehicle start disable history 6: None

Remote vehicle start disable history 7: None

Remote vehicle start disable history 8: None

ECM response source: Ignition switch start

ECM authentication status: Unknown

ECM challenge status: Invalid

Immobilizer security information programmed: No

Immobilizer system status: Standby

Immobilizer password learn : Inactive

Immobilizer security code accepted: No

Immobilizer security code function: Not present

Immobilizer security code programmed: No

Immobilizer security code lockout: No

Immobilizer password learn scan tool delay: Inactive

Immobilizer auto learn counter: 0

Immobilizer automatic learn timer: 0 sec

MIL requested by DTC: No

Electric power management inhibit reason: None

Immobilizer valid response received time: 0 ms

Generator indicator command: Off

Power mode: Off

Engine oil absolute pressure sensor: 0 kPa

Engine oil pressure: 0.00 kPa

Ignition on/start circuit source bypass relay control circuit high voltage test status: Malfunction

Ignition on/start circuit source bypass relay control circuit low voltage test status: Malfunction

Ignition on/start circuit source bypass relay control circuit open test status: Malfunction

Immobilizer security code lockout active timer: 0 ms

Immobilizer security code programming counter: 0 Counts

Immobilizer security code reset counter: 0 Counts

VIN programing counter: 0

Calibration history

Number of calibration history events stored: 0

Calibration history buffer: Unlocked

Calibration part number history 1: --

Calibration verification number history 1: --

Calibration part number history 2: --

Calibration verification number history 2: --

Calibration part number history 3: --

Calibration verification number history 3: --

Calibration part number history 4: --

Calibration verification number history 4: --

Calibration part number history 5: --

Calibration verification number history 5: --

Calibration part number history 6: --

Calibration verification number history 6: --

Calibration part number history 7: --

Calibration verification number history 7: --

Calibration part number history 8: --

Calibration verification number history 8: --

Calibration part number history 9: --

Calibration verification number history 9: --

Calibration part number history 10: --

Calibration verification number history 10: --

VIN no: --

Inspection / Maintenance data

Engine coolant temperature sensor: -40 °C

Vehicle speed sensor: 0 km/h

Intake air temperature sensor: -40 °C

Remaining fuel in tank: 0.0 %

Baro: 0.0 kPa

Catalyst monitor enabled this ignition cycle: --

O2S/HO2S monitor enabled this ignition cycle: --

EVAP monitor enabled this ignition cycle: --

HO2S heater monitor enabled this ignition cycle: --

EGR/Camshaft position monitor enabled this ignition cycle: --

Catalyst monitor complete this ignition cycle: --

O2S/HO2S monitor complete this ignition cycle: --

EVAP monitor complete this ignition cycle: --

HO2S heater monitor complete this ignition cycle: --

EGR/Camshaft position monitor complete this ignition cycle: --

Ignition 1 signal: 0.00 V

Ambient air temperature: -40 °C

Fuel alcohol content: 0 %

Brake pedal position circuit signal: Released

Brake pedal position sensor signal: Released

Cold start: No

Coolant temperature at engine start: -40 °C

Remaining fuel in tank: 0 L

Engine off time: 00:00:00

Start-up IAT sensor: -40 °C

MIL requested by DTC: No

MIL command: Off

Fuel composition learn: Inactive

Calculated barometric pressure: 0 kPa

Inspection/Maintenance drive cycle complete: No

Inspection/Maintenance drive cycle vehicle speed time complete: No

Inspection/Maintenance drive cycle propulsion system active time complete: No

Inspection/Maintenance drive cycle idle time complete: No

Inspection / Maintenance system status data

Number of DTC: 0

Check engine telltale request: No

Misfire monitor enabled: No

Misfire monitor complete: Yes

Fuel system monitor enabled: No

Fuel system monitor complete: Yes

Component monitor enabled: No

Component monitor complete: Yes

Catalyst monitor enabled: --

Catalyst monitor enabled: --

O2S/HO2S monitor enabled: --

EVAP monitor enabled: --

HO2S heater monitor enabled: --

Secondary air injection system monitor enabled: --

EGR/Camshaft position monitor enabled: --

Catalyst monitor complete: --

Catalyst monitor complete: --

O2S/HO2S monitor complete: --

EVAP monitor complete: --

HO2S heater monitor complete: --

Secondary air injection system monitor complete: --

EGR/Camshaft position monitor complete: --

Check engine telltale request: No

Component monitor enabled: No

Component monitor complete: Yes

Catalyst monitor enabled: --

EVAP monitor enabled: --

Catalyst monitor complete: --

EVAP monitor complete: --

Engine load: 0.0 %

Engine coolant temperature sensor: -40 °C

Short term fuel trim bank 1: -100 %

Long term fuel trim bank 1: -100 %

Short term fuel trim bank 2: -100 %

Long term fuel trim bank 2: -100 %

Fuel pressure sensor: 0 kPa

MAP sensor: 0.0 kPa

Engine speed: 0 rpm

Vehicle speed sensor: 0 km/h

Ignition timing: -64.0 °

Intake air temperature sensor 1: -40 °C

Mass air flow sensor: 0.00 g/sec

Fuel rail pressure sensor 1: 0.0 MPa

Fuel rail pressure sensor: 0.0 MPa

EVAP purge solenoid valve command: 0 %

Remaining fuel in tank: 0.0 %

Warm-ups since DTC cleared: 0 Counts

Fuel tank pressure sensor: 0.00 in. H2O

Baro: 0.0 kPa

Barometric pressure sensor 1: 0 kPa

Calculated catalyst temperature bank 1: -40 °C

Calculated catalyst temperature bank 2: -40 °C

Component monitor enabled this ignition cycle: No

Component monitor complete this ignition cycle: Yes

Catalyst monitor enabled this ignition cycle: --

EVAP monitor enabled this ignition cycle: --

Catalyst monitor complete this ignition cycle: --

EVAP monitor complete this ignition cycle: --

Ignition 1 signal: 0.00 V

Air/Fuel equivalence ratio command: 0.00

Ambient air temperature: -40 °C

Target throttle position: 0 %

Fuel alcohol content: 0 %

Electronic throttle control (ETC) system forced engine shutdown: No

Reduced engine power: Inactive

Wide open throttle: No

APP sensor 1 and 2: Agree

Electronic throttle control (ETC) motor: Enabled

Throttle position sensors 1 and 2: Agree

A/C request: No

A/C cut-off due to A/C pressure out of range: No

A/C Off for WOT: No

A/C compressor clutch relay command: Off

Brake pedal position sensor fully released learn status: Incomplete

Extended travel brake pedal switch: Released

Extended travel brake pedal position signal: Released

TCC/Cruise control brake pedal switch: Released

Brake pedal position circuit signal: Released

Brake pedal position sensor signal: Released

Skip shift indicator command: Off

Clutch pedal starter inhibit switch: On

Clutch pedal switch: Released

Skip shift solenoid actuator command: Disabled

O2 sensor 2, bank 2 heater: Off

O2 sensor 2, bank 1 heater: Off

O2 sensor 1, bank 2 heater: Off

O2 sensor 1, bank 1 heater: Off

Engine oil pressure switch: Ok

Change engine oil indicator command: Off

Engine oil level switch: Ok

Fuel volatility: Low

Cold start: No

EVAP vent solenoid valve command: Not Venting

Starter relay command: Off

P/N switch: In gear

Engine controls ignition relay command: Off

Ignition accessory signal: Off

Remote vehicle start request signal: Off

Crank request signal: No

Power enrichment: Inactive

Fuel control loop status: Open

Deceleration fuel cut-off: Inactive

Fuel trim learn: Disabled

Cylinder 6 deactivation solenoid valve command: Off

Cylinder 7 deactivation solenoid valve command: Off

Cylinder 3 deactivation solenoid valve command: Off

Cylinder 1 deactivation solenoid valve command: Off

Cylinder 4 deactivation solenoid valve command: Off

Cylinder Deactivation System Command: Inactive

Throttle position performance test: Ok

MAP performance test 2: Ok

MAP performance test 1: Ok

Cylinder deactivation performance test: Ok

A/C high side pressure sensor: 0.00 V

Generator F terminal signal: 0.0 %

Fuel tank pressure sensor: 0.00 V

Fuel level sensor left tank: 0.00 V

Fuel level sensor: 0.00 V

Traction control torque request signal: 0.0 %

Engine oil pressure sensor: 0.00 V

Crankshaft position active counter: 0 Counts

Crankshaft position resync counter: 0 Counts

Coolant temperature at engine start: -40 °C

Traction control torque delivered signal: 0 %

Fuel trim memory cell: 0

Torque management ignition timing retard: 0.0 °

Knock retard: 0 °

Calculated air flow: 0.00 g/sec

Target idle speed: 0 rpm

Current misfire, cylinder 5: 0 Counts

Current misfire, cylinder 6: 0 Counts

Current misfire, cylinder 7: 0 Counts

Current misfire, cylinder 8: 0 Counts

Misfire historic, cylinder 5: 0 Counts

Misfire historic, cylinder 6: 0 Counts

Misfire historic, cylinder 7: 0 Counts

Misfire historic, cylinder 8: 0 Counts

Total number of misfire: 0 Counts

Misfire historic, cylinder 1: 0 Counts

Misfire historic, cylinder 2: 0 Counts

Misfire historic, cylinder 3: 0 Counts

Misfire historic, cylinder 4: 0 Counts

Current misfire, cylinder 2: 0 Counts

Current misfire, cylinder 1: 0 Counts

Current misfire, cylinder 3: 0 Counts

Current misfire, cylinder 4: 0 Counts

Cycles of misfire data: 0 Counts

Distance since DTC cleared: 0 km

Distance since first malfunction: 0 km

Distance since last malfunction: 0 km

Ignition cycles with malfunction since 1st malfunction: 0 Counts

Ignition cycles without malfunction since last malfunction: 0 Counts

Ignition cycles without completed test since 1st malfunction: 0 Counts

EVAP malfunction history: None

Accelerator pedal position sensors: 0 %

Throttle position: 0 %

Accelerator pedal position sensor 1: 0 %

Accelerator pedal position sensor 2: 0 %

Throttle position sensor 1: 0 %

Throttle position sensor 2: 0 %

Throttle position sensor 2: 0.00 V

Throttle position sensor 1: 0.00 V

Accelerator pedal position sensor 2: 0.00 V

Accelerator pedal position sensor 1: 0.00 V

Injection time bank 1: 0.00 ms

Injection time bank 2: 0.00 ms

Total knock retard: 0 °

Mass air flow sensor: 0 Hz

Crankshaft position variation learn crank pulse to cylinder count: No

Crankshaft position variation learn required engine speed: No

Misfire diagnostic engine speed: 0 rpm

Misfire diagnostic engine load: 0.0 %

EVAP service bay test result: No test result

EVAP service bay test abort reason: None

EVAP service bay test status: Waiting for purge enable

Cruise control disengagement 1st history: Brake pedal applied

Cruise control disengagement 2nd history: Brake pedal applied

Cruise control disengagement 3rd history: Brake pedal applied

Cruise control disengagement 4th history: Brake pedal applied

Cruise control disengagement 5th history: Brake pedal applied

Cruise control disengagement 6th history: Brake pedal applied

Cruise control disengagement 7th history: Brake pedal applied

Cruise control disengagement 8th history: Brake pedal applied

Accelerator pedal position: 0 %

Remaining fuel in tank: 0 L

Fuel level sensor right tank: 0.00 V

Catalyst monitor test counter bank 1: 0 Counts

Catalyst monitor test counter bank 2: 0 Counts

MIL control circuit high voltage test status: Malfunction

MIL control circuit low voltage test status: Malfunction

MIL control circuit open test status: Malfunction

Starter relay control circuit high voltage test status: Malfunction

Starter relay control circuit low voltage test status: Malfunction

Starter relay control circuit open test status: Malfunction

Fuel pump relay control circuit high voltage test status: Malfunction

Fuel pump relay control circuit low voltage test status: Malfunction

Fuel pump: Off

Fuel pump relay control circuit open test status: Malfunction

A/C compressor clutch relay control circuit high voltage test status: Malfunction

A/C compressor clutch relay control circuit low voltage test status: Malfunction

A/C compressor clutch relay control circuit open test status: Malfunction

Throttle position sensor 1 fully close learn: 0.00 V

Throttle position sensor 2 fully close learn: 0.00 V

Engine off time: 00:00:00

Throttle motor PWM control signal: 0 %

Generator L - terminal command: 0.0 %

Ignition coil 1 control circuit high voltage test status: Malfunction

Ignition coil 1 control circuit low voltage test status: Malfunction

Ignition coil 1 control circuit open test status: Malfunction

Ignition coil 2 control circuit high voltage test status: Malfunction

Ignition coil 2 control circuit low voltage test status: Malfunction

Ignition coil 2 control circuit open test status: Malfunction

Ignition coil 3 control circuit high voltage test status: Malfunction

Ignition coil 3 control circuit low voltage test status: Malfunction

Ignition coil 3 control circuit open test status: Malfunction

Ignition coil 4 control circuit high voltage test status: Malfunction

Ignition coil 4 control circuit low voltage test status: Malfunction

Ignition coil 4 control circuit open test status: Malfunction

Ignition coil 5 control circuit high voltage test status: Malfunction

Ignition coil 5 control circuit low voltage test status: Malfunction

Ignition coil 5 control circuit open test status: Malfunction

Ignition coil 6 control circuit high voltage test status: Malfunction

Ignition coil 6 control circuit low voltage test status: Malfunction

Ignition coil 6 control circuit open test status: Malfunction

Ignition coil 7 control circuit high voltage: Malfunction

Ignition coil 7 control circuit low voltage: Malfunction

Ignition coil 7 control circuit open test status: Malfunction

Ignition coil 8 control circuit high voltage test status: Malfunction

Ignition coil 8 control circuit low voltage test status: Malfunction

Ignition coil 8 control circuit open test status: Malfunction

Cylinder 1 injector control circuit high voltage test status: Malfunction

Cylinder 1 injector control circuit low voltage test status: Malfunction

Cylinder 1 injector control circuit open test status: Malfunction

Cylinder 2 injector control circuit high voltage test status: Malfunction

Cylinder 2 injector control circuit low voltage test status: Malfunction

Cylinder 2 injector control circuit open test status: Malfunction

Cylinder 3 injector control circuit high voltage test status: Malfunction

Cylinder 3 injector control circuit low voltage test status: Malfunction

Cylinder 3 injector control circuit open test status: Malfunction

Cylinder 4 injector control circuit high voltage test status: Malfunction

Cylinder 4 injector control circuit low voltage test status: Malfunction

Cylinder 4 injector control circuit open test status: Malfunction

Cylinder 5 injector control circuit high voltage test status: Malfunction

Cylinder 5 injector control circuit low voltage test status: Malfunction

Cylinder 5 injector control circuit open test status: Malfunction

Cylinder 6 injector control circuit high voltage test status: Malfunction

Cylinder 6 injector control circuit low voltage test status: Malfunction

Cylinder 6 injector control circuit open test status: Malfunction

EVAP purge solenoid valve control circuit high voltage test status: Malfunction

EVAP purge solenoid valve control circuit low voltage test status: Malfunction

EVAP purge solenoid valve control circuit open test status: Malfunction

EVAP vent solenoid valve control circuit high voltage test status: Malfunction

EVAP vent solenoid valve control circuit low voltage test status: Malfunction

EVAP vent solenoid valve control circuit open test status: Malfunction

Reverse inhibit solenoid actuator control circuit high voltage test status: Malfunction

Reverse inhibit solenoid actuator control circuit low voltage test status: Malfunction

Reverse inhibit solenoid actuator command: Off

Reverse inhibit solenoid actuator control circuit open test status: Malfunction

Skip shift solenoid actuator control circuit high voltage test status: Malfunction

Skip shift solenoid actuator control circuit low voltage test status: Malfunction

Skip shift solenoid actuator control circuit open test status: Malfunction

Camshaft position sensor: 0 rpm

Crankshaft position sensor: 0 rpm

O2 sensor 1, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit low voltage test status: Malfunction

O2 sensor 1, bank 1 heater control circuit open test status: Malfunction

O2 sensor 2, bank 1 heater control circuit high voltage test status: Malfunction

O2 sensor 2, bank 1 heater control circuit low voltage test status: Malfunction

HO2S heater control circuit open test status bank 1 sensor 2: Malfunction

O2 sensor 1, bank 2 heater control circuit high voltage test status: Malfunction

O2 sensor 1, bank 2 heater control circuit low voltage test status: Malfunction

O2 sensor 1, bank 2 heater control circuit open test status: Malfunction

O2 sensor 2, bank 2 heater control circuit high voltage test status: Malfunction

O2 sensor 2, bank 2 heater control circuit low voltage test status: Malfunction

O2 sensor 2, bank 2 heater control circuit open test status: Malfunction

5V reference voltage circuit 1: 0.00 V

5V reference voltage circuit 2: 0.00 V

Fuel pressure regulator high control circuit command: 0 %

Fuel pressure regulator 1 high control circuit command: 0 %

O2 sensor 1, bank 1 heater: 0 %

O2 sensor 1, bank 2 heater: 0 %

O2 sensor 1, bank 1 heater: 0.00 mA

O2 sensor 2, bank 1 heater: 0.00 mA

O2 sensor 1, bank 2 heater: 0.00 mA

O2 sensor 2, bank 2 heater: 0.00 mA

Engine controls ignition relay control circuit high voltage test status: Malfunction

Engine controls ignition relay control circuit low voltage test status: Malfunction

Engine controls ignition relay control circuit open test status: Malfunction

Engine controls ignition relay feedback signal: 0.0 V

Generator L-terminal circuit high voltage test status: Malfunction

Generator L-terminal circuit low voltage test status: Malfunction

Generator L - terminal command: Off

Generator L-terminal circuit open test status: Malfunction

Cruise control "On"/"Off" switch: Off

Cruise control "Set/Coast" switch: Off

Cruise control "Cancel" switch: Inactive

Cruise control "Resume/Accelerate" switch: Off

Cruise control switch: Active

A/C disengagement 1st history: None

A/C disengagement 2nd history: None

A/C disengagement 3rd history: None

A/C disengagement 4th history: None

A/C disengagement 5th history: None

A/C disengagement 6th history: None

A/C disengagement 7th history: None

A/C disengagement 8th history: None

Cylinder 1 deactivation solenoid valve control circuit high voltage test status: Malfunction

Cylinder 3 deactivation solenoid valve control circuit high voltage test status: Malfunction

Cylinder 3 deactivation solenoid valve control circuit low voltage test status: Malfunction

Cylinder 1 deactivation solenoid valve control circuit low voltage test status: Malfunction

Cylinder 3 deactivation solenoid valve control circuit open test status: Malfunction

Cylinder 1 deactivation solenoid valve control circuit open test status: Malfunction

Cylinder 7 deactivation solenoid valve control circuit high voltage test status: Malfunction

Cylinder 7 deactivation solenoid valve control circuit low voltage test status: Malfunction

Cylinder 7 deactivation solenoid valve control circuit open test status: Malfunction

Cylinder 6 deactivation solenoid valve control circuit high voltage test status: Malfunction

Cylinder 6 deactivation solenoid valve control circuit low voltage test status: Malfunction

Cylinder 6 deactivation solenoid valve control circuit open test status: Malfunction

Cylinder 4 deactivation solenoid valve control circuit high voltage test status: Malfunction

Cylinder 4 deactivation solenoid valve control circuit low voltage test status: Malfunction

Cylinder 4 deactivation solenoid valve control circuit open test status: Malfunction

Engine oil temperature sensor: -40 °C

Remote vehicle start disable history 1: None

Remote vehicle start disable history 2: None

Remote vehicle start disable history 3: None

Remote vehicle start disable history 4: None

Remote vehicle start disable history 5: None

Remote vehicle start disable history 6: None

Remote vehicle start disable history 7: None

Remote vehicle start disable history 8: None

Immobilizer security information programmed: No

Immobilizer system status: Standby

Immobilizer password learn : Inactive

Immobilizer security code accepted: No

Immobilizer security code function: Not present

Immobilizer security code programmed: No

Immobilizer security code lockout: No

Immobilizer password learn scan tool delay: Inactive

Immobilizer auto learn counter: 0

Immobilizer automatic learn timer: 0 sec

A/C high side pressure sensor: 0 kPa

EVAP service bay test inhibit reason: None

Engine off evap service bay test abort reason: None

Engine off evap service bay test inhibit reason: None

Engine off evap service bay test result: None

Distance to enable engine off evap service bay test: 0.0 km

Fuel trim system test state: Disabled

Short term fuel trim test average bank 1: -100 %

Short term fuel trim test average bank 2: -100 %

Long term fuel trim test average bank 1: -100 %

Long term fuel trim test average bank 2: -100 %

Long term fuel trim test average without purge bank 1: -100 %

Long term fuel trim test average without purge bank 2: -100 %

Knocking detected, cylinder 3: No

Knocking detected, cylinder 2: No

Knocking detected, cylinder 4: No

Knocking detected, cylinder 7: No

Knocking detected, cylinder 5: No

Knocking detected, cylinder 8: No

Knocking detected, cylinder 6: No

Knocking detected, cylinder 1: No

Injector disabled, cylinder 3 - misfire detected: No

Injector disabled, cylinder 2 - misfire detected: No

Injector disabled, cylinder 4 - misfire detected: No

Injector disabled, cylinder 7 - misfire detected: No

Injector disabled, cylinder 5 - misfire detected: No

Injector disabled, cylinder 8 - misfire detected: No

Injector disabled, cylinder 6 - misfire detected: No

Injector disabled, cylinder 1 - misfire detected: No

Cooling fan speed: 0 rpm

Target cooling fan control: 0 %

O2 sensor 2, bank 2 heater: 0 %

O2 sensor 2, bank 1 heater: 0 %

Camshaft position: 0 °

Camshaft position variance: 0

Camshaft position active counter: 0 Counts

Transmission oil temperature: -40 °C

Output shaft speed sensor: 0 rpm

Torque delivered signal: 0.00 N·m

Engine oil pressure control test counter: 0 Counts

14V power module setpoint: 0 %

14V power module setpoint: 0.00 V

MAP sensor: 0.00 V

Supercharger inlet pressure: 0.00 V

Start-up IAT sensor: -40 °C

Intake air temperature sensor 1 at start: -40 °C

Intake air temperature sensor 2: -40 °C

Barometric pressure sensor 1: 0.00 V

Barometric pressure sensor: 0.00 V

Supercharger bypass solenoid valve command: 0.0 %

Supercharger bypass solenoid valve control circuit high voltage test status: Malfunction

Supercharger bypass solenoid valve control circuit low voltage test status: Malfunction

Supercharger bypass solenoid valve control circuit open test status: Malfunction

Charge air cooler coolant pump relay control circuit high voltage test status: Malfunction

Charge air cooler coolant pump relay control circuit low voltage test status: Malfunction

Charge air cooler coolant pump relay command: Off

Charge air cooler coolant pump relay control circuit open test status: Malfunction

Distance with cylinder deactivated: 0 km

Distance with cylinder activated: 0 km

Cylinder deactivation cycles: 0 Counts

Cylinder deactivation inhibit - ECT: No

Cylinder deactivation inhibit - APP high: No

Cylinder deactivation inhibit - engine oil temperature: No

Cylinder deactivation inhibit - APP rate high: No

Cylinder deactivation inhibit - engine oil pressure: No

Cylinder deactivation inhibit - brake booster weak vacuum: No

Cylinder deactivation inhibit - ignition voltage: No

Cylinder deactivation inhibit - intake manifold weak vacuum: No

Cylinder deactivation inhibit - oil aeration: No

Cylinder deactivation inhibit - transmission shifting: No

Cylinder deactivation inhibit - maximum deactivation time exceeded: No

Cylinder deactivation inhibit - transmission range: No

Cylinder deactivation inhibit - minimum time on all cylinders: No

Cylinder deactivation inhibit - transmission gear: No

Cylinder deactivation inhibit - scan tool override: No

Cylinder deactivation inhibit - engine speed: No

Cylinder deactivation inhibit - acceleration request: --

Cylinder deactivation inhibit - A/C compressor clutch on: --

Cylinder deactivation inhibit - vehicle speed too low: --

Cylinder deactivation inhibit - heater performance: --

Cylinder deactivation inhibit - rpm limit: --

Cylinder deactivation inhibit - 4WD low engaged: --

Cylinder deactivation inhibit - injector stable time: --

Cylinder deactivation inhibit - HO2S 2 test: --

Cylinder deactivation inhibit - deceleration fuel cut-off: --

Cylinder deactivation inhibit - fuel alcohol content too high: --

Cylinder deactivation inhibit - fuel alcohol content learn in progress: --

Cylinder deactivation inhibit - minimum time after TAC DTC: --

Cylinder deactivation inhibit - maximum throttle exceeded: --

Cylinder deactivation inhibit - catalyst temperature low: --

Cylinder deactivation inhibit - cylinder deactivation solenoid valve DTC: No

Cylinder deactivation inhibit - engine oil pressure sensor DTC: No

Cylinder deactivation inhibit - VSS DTC: No

Cylinder deactivation inhibit - tac system DTC: No

Cylinder deactivation inhibit - iat sensor DTC: No

Cylinder deactivation inhibit - brake booster pressure sensor DTC: No

Cylinder deactivation inhibit - ECT sensor DTC: No

Cylinder deactivation inhibit - map sensor DTC: No

Cylinder deactivation inhibit - catalyst overtemperature protection: No

Cylinder deactivation inhibit - engine controls ignition relay DTC: No

Cylinder deactivation inhibit - engine overtemperature protection: No

Cylinder deactivation inhibit - camshaft position sensor DTC: No

Cylinder deactivation inhibit - axle torque limiting: No

Cylinder deactivation inhibit - crankshaft position sensor DTC: No

Cylinder deactivation inhibit - torque reduction: No

Cylinder deactivation inhibit - misfire DTC: No

Cylinder deactivation inhibit - cylinder deactivation system DTC: --

Cylinder deactivation inhibit - 4WD low state invalid: --

Cylinder deactivation inhibit - hot coolant mode: --

Cylinder deactivation inhibit - calculated torque: --

Cylinder deactivation inhibit - piston protection: --

Cylinder deactivation disable history 1: None

Cylinder deactivation disable history 2: None

Cylinder deactivation disable history 3: None

Cylinder deactivation disable history 4: None

Cylinder deactivation disable history 5: None

Cylinder deactivation disable history 6: None

Cylinder deactivation disable history 7: None

Cylinder deactivation disable history 8: None

Clutch pedal position sensor: 0.00 V

Clutch pedal position sensor learned apply position: 0.00 V

Clutch pedal position learn status: Performed successfully

Clutch pedal position sensor learned release position: 0.00 V

Clutch pedal position sensor: 0 %

MIL requested by DTC: No

MIL command: Off

Check engine telltale: Off

Traction control: Inactive

5V reference voltage circuit 4: Ok

5V reference voltage circuit 3: Ok

5V reference voltage circuit 2: Ok

5V reference voltage circuit 1: Ok

Fuel composition learn: Inactive

Torque request inhibit - minimum torque: No

Torque request inhibit - fuel: No

Torque request inhibit - TAC limit: No

Torque request inhibit - ignition timing: No

Torque request inhibit - ignition timing advance: No

Torque request inhibit - TAC: No

Torque request inhibit - minimum idle: No

Transfer case OSS: 0 rpm

5V reference voltage circuit 3: 0.00 V

5V reference voltage circuit 4: 0.00 V

Radiator coolant temperature sensor: -40 °C

Target engine coolant temperature: -40 °C

Immobilizer valid response received time: 0 ms

Cruise control inhibit reason: Brake pedal applied

Throttle body idle air flow compensation: 0 %

Cruise control: Disabled

Generator indicator command: Off

Catalyst monitor test result bank 1: No decision

Catalyst monitor test result bank 2: No decision

Catalyst monitor not at idle test conditions met: No

Catalyst monitor test state: Inactive

Reduced engine power history: None

Power mode: Off

Cylinder 1 injector control circuit status: Ok

Cylinder 2 injector control circuit status: Ok

Cylinder 3 injector control circuit status: Ok

Cylinder 4 injector control circuit status: Ok

Cylinder 5 injector control circuit status: Ok

Cylinder 6 injector control circuit status: Ok

Cylinder 7 injector control circuit status: Ok

Cylinder 8 injector control circuit status: Ok

Fuel pressure regulator 1 control circuit high voltage test status: Malfunction

Fuel pressure regulator control circuit high voltage test status: Malfunction

Fuel pressure regulator 1 control circuit low voltage test status: Malfunction

Fuel pressure regulator control circuit low voltage test status: Malfunction

Fuel pressure regulator control circuit command: Off

Fuel pressure regulator 1 command: Off

Fuel pressure regulator 1 control circuit open test status: Malfunction

Fuel pressure regulator control circuit open test status: Malfunction

Fuel pressure regulator high control circuit high voltage test status: Malfunction

Fuel pressure regulator 1 high control circuit high voltage test status: Malfunction

Fuel pressure regulator high control circuit low voltage test status: Malfunction

Fuel pressure regulator 1 high control circuit low voltage test status: Malfunction

Fuel pressure regulator 1 high control circuit command: Off

Fuel pressure regulator high control circuit command: Off

Fuel pressure regulator high control circuit open test status: Malfunction

Fuel rail pressure regulator command: 0 °

Intake manifold pressure: 0 kPa

Ignition coil supply voltage bank 2: Off

Ignition coil supply voltage bank 1: Off

Fuel composition sensor: 0 Hz

Accelerator pedal position sensor 2 - circuit status: Ok

Accelerator pedal position sensor 1 - circuit status: Ok

Brake pedal position sensor: 0.00 V

Brake pedal position sensor learned released position: 0.00 V

Brake pedal position sensor: 0 %

Fuel injector driver supply voltage: 0.0 V

Calculated barometric pressure: 0 kPa

Intake air temperature sensor 2: 0 Hz

Ambient humidity: 0 %

Intake air humidity sensor: 0 %

Specific humidity: 0.00 %

O2 sensor 1, bank 1: 0.00 V

O2 sensor 2, bank 1: 0.00 V

O2 sensor 1, bank 2: 0.00 V

O2 sensor 2, bank 2: 0.00 V

MAF sensor supply voltage control circuit high voltage test status: Malfunction

MAF sensor supply voltage control circuit low voltage test status: Malfunction

MAF sensor supply voltage command: Off

MAF sensor supply voltage control circuit open test status: Malfunction

Crankshaft position signal output circuit high voltage test status: Malfunction

Crankshaft position signal output circuit low voltage test status: Malfunction

Crankshaft position signal output circuit open test status: Malfunction

Camshaft position signal output circuit high voltage test status: Malfunction

Camshaft position signal output circuit low voltage test status: Malfunction

Camshaft position signal output circuit open test status: Malfunction

Engine oil absolute pressure sensor: 0 kPa

Engine oil pressure: 0.00 kPa

Engine speed during misfire history 1: 0 rpm

Engine load during misfire history 1: -- %

Engine speed during misfire history 2: 0 rpm

Engine load during misfire history 2: -- %

Engine speed during misfire history 3: 0 rpm

Engine load during misfire history 3: -- %

Engine speed during misfire history 4: 0 rpm

Engine load during misfire history 4: -- %

Engine speed during misfire history 5: 0 rpm

Engine load during misfire history 5: -- %

Target fuel pressure: 0 kPa

Fuel pressure sensor: 0.0 V

Active grille air shutter position command: 0 %

Active grille air shutter position: 0 %

Driver requested axle torque: -22534 N·m

Fuel rail temperature sensor 1: -40 °C

Fuel rail temperature sensor 2: -40 °C

Barometric pressure sensor 2: 0.00 V

Barometric pressure sensor 2: 0 kPa

Accelerator pedal position sensor 1 learned applied position: 0 %

Accelerator pedal position sensor 2 learned applied position: 0 %

A/T output speed: 0 rpm

Target fuel rail pressure: 0.0 MPa

Fuel rail pressure sensor 1: 0.00 V

Fuel rail pressure sensor: 0.00 V

Current gear: In progress

Engine overspeed: Not present

Total engine overspeed time: 0 ms

Accelerator pedal position sensor 1 learned released position: 0.00 V

Accelerator pedal position sensor 2 learned released position: 0.00 V

Engine oil pressure control solenoid valve control circuit high voltage test status: Malfunction

Engine oil pressure control solenoid valve control circuit low voltage test status: Malfunction

Engine oil pressure control solenoid valve command: Off

Engine oil pressure control solenoid valve control circuit open test status: Malfunction

Fuel rail pressure sensor 2: 0.00 V

Fuel rail pressure sensor 2: 0.0 MPa

Gate select position sensor learned position: 0 %

Gear shift position sensor learned position: 0 %

Gear shift position: Unknown

Gear position sensor learn status: Complete

Gear position sensor learn abort reason: None

Distance since excessive clutch slip detected: 0 km

Fuel rail pressure sensor 1: 0 Counts

Fuel rail pressure sensor 2: 0 Counts

Ignition on/start circuit source bypass relay control circuit high voltage test status: Malfunction

Ignition on/start circuit source bypass relay control circuit low voltage test status: Malfunction

Ignition on/start circuit source bypass relay control circuit open test status: Malfunction

Immobilizer security code lockout active timer: 0 ms

Immobilizer security code programming counter: 0 Counts

Immobilizer security code reset counter: 0 Counts

Engine overspeed event data

Maximum engine speed when engine overspeed detected: 0 rpm

Engine speed when engine overspeed detected: 0.0 rpm

Vehicle speed when engine overspeed detected: 0 km/h

Accelerator pedal position when engine overspeed detected: 0.0 %

Engine oil temperature when engine overspeed detected: -40 °C

MAF when engine overspeed detected: 0.00 g/sec

Odometer when engine overspeed detected: 0 km

Engine overspeed counter: 0 Counts

Engine overspeed: Not present

Total engine overspeed time: 0 ms

Engine oil level warning event data

Oil level warning counter highway: 0

Oil level warning counter country road: 0

Oil level warning counter city: 0

Distance since last oil level warning: 0 km

Distance since last oil pressure warning: 0 km

Actuators test

Controls

A/C compressor clutch relay

Active grille air shutter

Active grille air shutter 1

Active grille air shutter 2

Camshaft position actuator

Camshaft position actuator

Charge air cooler coolant pump

Compression test

Compression test

Cooling fan

Cooling fan

Cylinder deactivation system

Cylinder 1

Cylinder 3

Cylinder 4

Cylinder 6

Cylinder 7

Engine controls ignition relay

Engine oil pressure control solenoid valve

Engine speed

Throttle position

Throttle position

Throttle position

Throttle position

Evaporative emission (EVAP) system, canister purge valve

Evaporative emission (EVAP) system, canister vent valve

EVAP purge/seal

Fuel control loop status

Cylinder power balance

Cylinder power balance

Depressurize fuel system

Fuel injector balance

Fuel injector balance

Fuel pressure regulator

Fuel pump enable

Fuel rail pressure

Fuel pump enable

Ignition on/start switch circuit

Fuel pump trim reset

Fuel composition reset

Generator L terminal

Idle ignition timing

Ignition timing retard

Check engine telltale

O2 sensor 1, bank 1 heater

O2 sensor 2, bank 1 heater

O2 sensor 1, bank 2 heater

O2 sensor 2, bank 2 heater

O2 sensor 1, bank 1 heater

O2 sensor 2, bank 1 heater

O2 sensor 1, bank 2 heater

O2 sensor 2, bank 2 heater

Secondary air injection system pump relay

Secondary air injection solenoid valve

Secondary air injection system

EVAP service bay test

Skip shift solenoid actuator

Starter relay

Turbocharger bypass solenoid valve