Car, CHEVROLET, Silverado, 2019, Transfer case module

Clear DTC

Engine speed: 0 rpm

Vehicle speed: 0 km/h

Warm-ups since DTC cleared: 0 Counts

Control module voltage: 0.0 V

Brake pedal position sensor signal: Invalid

Front axle engagement feedback switch: Disengaged

Distance since first malfunction: 0 km

Distance since last malfunction: 0 km

Ignition cycles with malfunction since 1st malfunction: 0 Counts

Ignition cycles without malfunction since last malfunction: 0 Counts

Ignition cycles without completed test since 1st malfunction: 0 Counts

Transmission oil temperature: -40 °C

A/T output speed: 0 rpm

Power mode: Off

Ignition 1 signal: Off

Ignition accessory signal: Off

Transfer case clutch torque: 0 N·m

Requested transfer case clutch torque: 0 N·m

Range actuator brake control circuit high side voltage: 0.00 V

Transfer case range position sensor: 0 %

Transfer case range position sensor: 0 Hz

Sensor reference voltage 1: 0.00 V

Sensor reference voltage 2: 0.00 V

Sensor reference voltage 3: 0.00 V

Transfer case range selection switch state: Inactive

Transfer case range selection switch: 0.00 V

Range actuator position: Invalid

Range actuator direction: Invalid

Range actuator position sensor: 0.0 °

Range actuator position sensor: 0.00 V

Range actuator position sensor direction signal: 0.00 V

Range actuator direction command: Stationary

Range actuator command: 0 %

Range actuator control circuit high voltage test status: Malfunction

Range actuator control circuit low voltage test status: Malfunction

Range actuator control circuit open test status: Malfunction

Range actuator lock control circuit high voltage test status: Malfunction

Range actuator lock control circuit low voltage test status: Malfunction

Range actuator lock command: Locked

Range actuator lock control circuit open test status: Malfunction

Transfer case range position sensor: 0.0 °

Transfer case neutral range indicator control circuit high voltage test status: Malfunction

Transfer case neutral range indicator control circuit low voltage test status: Malfunction

Transfer case neutral range indicator command: Off

Transfer case neutral range indicator control circuit open test status: Malfunction

4WD low range indicator control circuit high voltage test status: Malfunction

4WD low range indicator control circuit low voltage test status: Malfunction

4WD low range indicator command: Off

4WD low range indicator control circuit open test status: Malfunction

2WD high range indicator control circuit high voltage test status: Malfunction

2WD high range indicator control circuit low voltage test status: Malfunction

2WD high range indicator command: Off

2WD high range indicator control circuit open test status: Malfunction

4WD high range indicator control circuit high voltage test status: Malfunction

4WD high range indicator control circuit low voltage test status: Malfunction

4WD high range indicator command: Off

4WD high range indicator control circuit open test status: Malfunction

4WD automatic range indicator control circuit high voltage test status: Malfunction

4WD automatic range indicator control circuit low voltage test status: Malfunction

4WD automatic range indicator command: Off

4WD automatic range indicator control circuit open test status: Malfunction

Vehicle stability control request: 0 %

Transfer case commanded position: Neutral

Range actuator position sensor low reference command: Off

Front axle engagement actuator control circuit high voltage test status: Malfunction

Front axle engagement actuator control circuit low voltage test status: Malfunction

Front axle engagement actuator command: Disengaged

Front axle engagement actuator control circuit open test status: Malfunction

Non-driven wheel speed: 0 km/h

Variation between transfer case range position sensor and range actuator position sensor: 0.0 °

Variation allowed between transfer case range position sensor and range actuator position sensor: 0.0 °

Range actuator current: 0.0 A

Range actuator position sensor supply voltage command: Off

Calculated transfer case clutch temperature: -40.0 °C

Steering wheel angle: 0 °

Transfer case output shafts slip speed: 0 rpm

Current transmission gear ratio: Invalid

Left front wheel speed sensor: 0 km/h

Right front wheel speed sensor: 0 km/h

Right rear wheel speed sensor: 0 km/h

Left rear wheel speed sensor: 0 km/h

Display dimming: 0 %

Range actuator brake control circuit low side voltage: 0.00 V

Transfer case clutch identifier: --

Transfer case clutch low control: -- °

Transfer case clutch high control: -- °

4WD crawl mode: --

Hardware version: --

VIN no: W0LGT8EBXA1007787

Identifier: 00 00

Software version: --

Calibration part number: --

End model part number: --

Base model part number: --

Engine speed: 0 rpm

Vehicle speed: 0 km/h

Warm-ups since DTC cleared: 0 Counts

Control module voltage: 0.0 V

Brake pedal position sensor signal: Invalid

Distance since first malfunction: 0 km

Distance since last malfunction: 0 km

Ignition cycles with malfunction since 1st malfunction: 0 Counts

Ignition cycles without malfunction since last malfunction: 0 Counts

Ignition cycles without completed test since 1st malfunction: 0 Counts

Transmission oil temperature: -40 °C

A/T output speed: 0 rpm

Power mode: Off

Ignition 1 signal: Off

Ignition accessory signal: Off

Axle torque: -22534 N·m

Transfer case clutch engagement: 0 %

Transfer case clutch torque: 0 N·m

Requested transfer case clutch torque: 0 N·m

Transfer case range position sensor: 0 %

Transfer case range position sensor: 0 Hz

Sensor reference voltage 1: 0.00 V

Sensor reference voltage 2: 0.00 V

Sensor reference voltage 3: 0.00 V

Transfer case range selection switch state: Inactive

Transfer case range selection switch: 0.00 V

Range actuator position: Invalid

Range actuator direction: Invalid

Range actuator position sensor: 0.0 °

Range actuator position sensor: 0.00 V

Range actuator position sensor direction signal: 0.00 V

Range actuator direction command: Stationary

Range actuator command: 0 %

Range actuator lock command: Locked

Transfer case range position sensor: 0.0 °

Transfer case range: Invalid

Vehicle stability control request: 0 %

Transfer case commanded position: Neutral

Non-driven wheel speed: 0 km/h

Distance this driving cycle: 0 km

Range actuator current: 0.0 A

Range actuator learn status: Not learned

Calculated transfer case clutch temperature: -40.0 °C

Steering wheel angle: 0 °

Transfer case output shafts slip speed: 0 rpm

Current transmission gear ratio: Invalid

Left front wheel speed sensor: 0 km/h

Right front wheel speed sensor: 0 km/h

Right rear wheel speed sensor: 0 km/h

Left rear wheel speed sensor: 0 km/h

Display dimming: 0 %

Range actuator position: Invalid

Transfer case range: Invalid

Range actuator learn status: Not learned

Range actuator position: Invalid

Range actuator position sensor: 0.0 °

Transfer case range position sensor: 0.0 °

Transfer case range: Invalid

Variation between transfer case range position sensor and range actuator position sensor: 0.0 °

Variation allowed between transfer case range position sensor and range actuator position sensor: 0.0 °

Range actuator learn status: Not learned

Transfer case clutch low value: -- °

Transfer case clutch high value: -- °

Transfer case range: Invalid

Transfer case commanded position: Neutral

Range actuator learn status: Not learned

Transfer case clutch identifier: --

2WD high range indicator

4WD automatic range indicator

4WD high range indicator

4WD low range indicator

Transfer case neutral range indicator

Transfer case clutch engagement

Transfer case range

Transfer case clutch high control

Transfer case clutch low control