Bil, GWM, HAVAL JOLION, Transmission control unit 7DCT-450 (TCU)
transakse - Transmission control unit 7DCT-450 (TCU) - 0
Identifikation
Application software programming attempt counter: 1999778612
Maximum allowable program number: 1999778612
Application software programming success counter: 1999778612
Vehicle configuration 2: --
Hardware number: 38
Hardware version nummer: 55
Bilkonfiguration: 0000000000000000000000000000000000
Vehicle network configuration data: --
Active diagnostic session: Standard
Running software ID: forbeholdt
Working mode: --
ASW code label: --
ASW calibration label: --
BSW code label: --
Manufacture bootloader software version number: --
Application software identification: --
Vehicle manufacturer spare part number: H23456789@ABCDE
Vehicle manufacturer ECU software version number: --
Leverandøridentifikation: AABIS
Supplier ECU manufacture date: H23456
Serie nummer: V23456
Factory ID and production line number: V23456789@AB
Stel nr.:
Software nummer: --
Software version number: --
C-Matrix version: --
Control unit network version 2: w23456789@
Calibration software version number: --
ECU level network configuration: --
Identificere : w23456789
Node address: w23456789
Comp identifier 1: --
Navn: --
Tool version: w2345678
Comp identifier 2: --
Calibration software version number: --
Manufacture bootloader software version number: --
UIN: --
Application software fingerprint: --
Fejlkoder
Controls
Clear DTC
Levende Data
ODD shaft speed: 7200 Omdr.
EVEN shaft speed: -100 Omdr.
Odd clutch VFS solenoid current (measured): 240 mA
Even clutch VFS solenoid current (measured): 1530 mA
Parking position: forbeholdt
Shift lever position: 35 %
Pressure clutch 1: 2626 mbar
Pressure clutch 2: 2112 mbar
Indgangsomdrejningstal, gearkasse: -100 Omdr.
Line MDA solenoid current (measured): 1530 mA
Lube ACS solenoid current (measured): 1530 mA
Shift fork A position (corrected): 8.74 mm
Shift fork B position (corrected): 10.24 mm
Shift fork C position (corrected): 6.74 mm
Shift fork D position (corrected): 5.00 mm
Net engine torque: 339 N·m
Gaspedalposition: 36.5 %
Ambient temperature: 21 °C
Supply voltages: terminal 30: 4.68 V
Gear position (current): R
Target gear: --
Køretøjs hastighed : 44 km/h
Engine torque (Driver request): 148 N·m
Torque losses: 148 N·m
Clutch 1 target torque: 336 N·m
Clutch 2 target torque: 592 N
Clutch temperature: -- °C
Motor Hastighed: 0 Omdr.
Bremsetrykføler: -5636 mbar
Motor kølevæske temperatur føler: 85 °C
Ambient air pressure: 342 mbar
Venstre forhjulshastighedsføler: 9.00 m/s
Højre forhjulshastighedsføler: -19.00 m/s
Venstre baghjuls hastighedsføler: -28.00 m/s
Højre baghjulshastighedsføler: 4.5 m/s
Odd AR MDA solenoid current (measured): 1530 mA
Even AR MDA solenoid current (measured): 102 mA
ACS 1 solenoid current (measured): 1530 mA
ACS 2 solenoid current (measured): -- mA
ACS 3 solenoid current (measured): 1530 mA
ACS 4 solenoid current (measured): 1530 mA
Hpark hydraulic valve actual current (measured): 438 mA
Hpark magnet actual current (measured): 1530 mA
P sensor teach-in value: 46.28 %
P sensor teach-in status: Sluk
Clutch (odd) pressure sensor: 4369 mbar
Clutch (even) pressure sensor: 8704 mbar
Read gearbox variant selector: --
Hpark hydraulic valve current (desired): 4677 mA
Hpark magnet valve current (desired): 65535 mA
Terminal 15 (ignition): 4660 mV
Supply voltage 5V N1: 4626 mV
Supply voltage 5V N2: 4626 mV
Supply voltage 8V N1: 8481 mV
Supply voltage 8V N2: 8995 mV
Main ECU voltage supply: 9509 mV
Oil temperature: 85 °C
Engine water pump speed: 4370 Omdr.
OBD PIDs supported: --
OBD requirements for which this vehicle or engine is certified: --
Distance since check engine telltale on: 16 km
Number of warm-ups since DTC cleared: 25 Cycles
Afstand siden fejlkode slettet: 8481 km
Water pump: 46260 %
Paddle shift: 4369
Check engine telltale request from transmission control module: Sluk
EP switch On/Off solenoid command: forbeholdt
Muligheder
Controls
Rediger stel nr.
Redigere konfiguration
Switch OFF auto P function
Transmission adaptation (After-sale learn function)
OFF DEV CAN function