Car, ACURA, ILX, Robotized gearbox (i-SHIFT)

Identifier: 00 08 40 40 10

Part number: 28125-RPJ-L070

P0603: Internal control module keep alive memory (KAM) error

P0974: Unknown DTC

P0977: Unknown DTC

P0980: Unknown DTC

P0983: Unknown DTC

P0108: Unknown DTC

U0028: Unknown DTC

P0713: Unknown DTC

P2122: Unknown DTC

Clear DTC

Engine torque: -86.35 N·m

Accelerator pedal position sensor: 5.64 °

Target idle speed: 854 rpm

Clutch slip: -8635 rpm

Left front wheel speed sensor: 13398 rpm

Right front wheel speed sensor: 63487 rpm

Left rear wheel speed sensor: 30019 rpm

Right rear wheel speed sensor: 10121 rpm

System voltage: 655.35 V

Clutch temperature: 65535 °C

Engine speed: 1110 rpm

Clutch actuator temperature: -8636 °C

TCM power circuit board temperature: 853 °C

Intake air temperature sensor: 837 °C

Engine coolant temperature sensor: 69

Brake pedal switch normally open: On

Brake pedal switch normally closed: Off

Brake switch AND signal: On

Wheel speed: 13944 rpm

Transmission gear command: 1

Gear position (current): 1

HAC switch (CAN): Off

Starter operation command: Off

ABS state: Not active

Cruise control: Not active

VSA system: Equip

VSA status: Not active

Cruise control shift down request 1: Off

Cruise control shift down request 2: Off

Ignition switch (input): On

Buzzer request: Off

Clutch closed position: Open

Auto mode gauge display: On

i-SHIFT telltale: On

Creep control system: Not active

Starter enable signal: Disable

Brake pedal switch: On

Clutch open position: Open

Clutch contact position 1 learning condition: Learnt

Clutch contact position 2 learning condition: Learnt

Clutch contact position 3 learning condition: Learnt

Learnt end position gear 1: Learnt

Learnt end position gear 2: Learnt

Learnt end position gear 3: Learnt

Learnt end position gear 4: Learnt

Learnt end position gear 5: Learnt

Learnt end position gear 6: Learnt

Learnt end position gear reverse: Learnt

Learnt synchronizer position gear 1: Learnt

Learnt synchronizer position gear 2: Learnt

Learnt synchronizer position gear 3: Learnt

Learnt synchronizer position gear 4: Learnt

Learnt synchronizer position gear 5: Learnt

Learnt synchronizer position gear 6: Learnt

All outputs valid: Disable

Hardware valid: Enable

Steering wheel downshift (-) switch command: Enable

Steering wheel upshift (+) switch command: Enable

Shift valid - A/M: Valid

Shift valid D: Valid

Shift valid N: Valid

Shift valid R: Valid

Steering shiftmatic down switch: Off

Steering shiftmatic up switch: Off

Manual mode: Auto

Drive: On

Neutral: On

Reverse: Off

Shifter in middle of R and N position: Off

Shifter in middle of D and N position: Off

Gear lever position - tip minus: Off

Gear lever position - tip plus: Off

Gear lever position - drive: On

Gear lever position - A/M: Off

Gear lever position - neutral: Off

Gear lever position - reverse: Off

Long term clutch contact point learned value: 14.00 mm

Medium term clutch contact point learned value: 172.20 mm

Short term clutch contact point learned value: 93.01 mm

Target clutch position: 569.01 mm

Actual clutch position: 491.51 mm

Shift position gear 1: 23.00 mm

Shift position gear 2: 4.00 mm

Shift position gear 3: 18.92 mm

Shift position gear 4: -86.36 mm

Shift position gear 5: 46.59 mm

Shift position gear 6: -73.39 mm

Reverse gear position (shift): 300.01 mm

Select position gear 1: -0.02 mm

Select position gear 2: 221.35 mm

Select position gear 3: -4.44 mm

Select position gear 4: 9.09 mm

Select position gear 5: -8.00 mm

Select position gear 6: 12.00 mm

Reverse gear position (select): -6.00 mm

Neutral gear position (select): 5.64 mm

Learnt synchronizer position gear 1: 0.19 mm

Learnt synchronizer position gear 2: -6.91 mm

Learnt synchronizer position gear 3: -5.00 mm

Learnt synchronizer position gear 4: -6.89 mm

Learnt synchronizer position gear 5: 8.21 mm

Learnt synchronizer position gear 6: 1.11 mm

Friction coefficient 1: 699

Friction coefficient 2: 699

Friction coefficient 3: 699

General friction coefficient: 695

Gate width gear 1: 11.10 mm

Gate width gear 2: -86.35 mm

Gate width gear 3: -70.82 mm

Gate width gear 4: 265.12 mm

Gate width gear 5: 136.88 mm

Gate width gear 6: 54.79 mm

Gate width gear R: -71.45 mm

Clutch fluid filling

Clutch fluid air bleeding

Static mode learning

Dynamic mode learning

Shift motor calibration

Engage gear test

Clutch actuator full stroke operation test

Gear box self test